Sony Tav L1 Operating Instructions

11 GB
xAuto input select button F
While the input is except DVD, if you press Z on the 
system or H, the input will be changed to DVD 
automatically.
This system has various types of menus:
 TV: TV MENU
 DVD: DVD MENU
DVD TOP MENU
DVD DISPLAY
 FM: FM MENU
 These menus are available when either input is 
selected.
 TV/DVD/FM: AMP MENU
xCURSOR MODE buttons B
When one of these buttons lights up, you can operate 
its menu (

12 GB
1/  – Input select/Text hold
 In TV mode (page 25): Selects the input source  from equipment connected to the system.
 In Text mode (page 21): Holds the current page.
 In TV/DVD/FM mode (page 10): Switches the  input source.
 – Lift up/down (page 71)
" /1  – On/standby (page 20)
Switches off the system temporarily. The  1 
(standby) indicator on the system (front of the lift 
unit) lights up. Press again to switch on the system 
from the standby mode.  – Sleep timer (page 42)
3 Number...

13 GB
Overview of the system/
lift unit buttons and 
indicators
Touch panel buttons (2 – 9): Touch any of these 
buttons once, to activate the panel (buttons light up), then 
touch the desired button.
1Disc slot
2Z – Eject
Eject a disc.
3H – Play
Play a disc.
4x – Stop
Stop a disc.52 +/– – Volume
Increases (+)/decreases (–) volume.
6PROG +/–
 In TV mode: Select next (+)/previous (–) 
channel.
 In FM mode: Select next (+)/previous (–) preset 
station.
7FM
Change input select to FM directly.
8TV
Change...

14 GB
1: Checking the 
accessories
Remote RM-ANU005 (1)
Size AA batteries (R6 type) (2)
AC power cord (mains lead) (1)
Screws (2)
FM wire antenna (aerial) (1)
Frame grille (1)
Quick Start Guide (1)
2: Inserting batteries 
into the remote
Notes
 Observe the correct polarity when inserting batteries.
 Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of the battery. 
Please consult your local authority.
 Do not use different types of batteries together or...

Getting Started
15 GB
3: Connecting a TV aerial/VCR/DVD player
1Remove the covers.
When all connections have been made, replace the 
covers.
2Connect your aerial to the   socket on 
the rear of the system.
If connecting to an aerial only
Go to step 4.
3Connect your VCR/DVD player.
1Connect the   socket on the rear of the 
system to the input socket on your VCR with 
the RF lead.
2 Connect the scart socket on your VCR/DVD 
player to the  / 1 or 2 scart socket on 
the rear of the system with a scart...

16 GB
2Secure the wall anchor bracket to a wall 
or pillar.
3Thread the rope or chain through both 
holes of the screws, and then tighten the 
other end of the rope or chain to the wall 
anchor bracket.
4: Connecting the FM 
wire antenna (aerial)
Connect the supplied FM wire antenna (aerial) for 
listening to the FM radio. Thread the wire antenna 
(aerial) through the slit of the cover, and then replace 
the cover. 
Notes
 Be sure to fully extend the FM wire antenna (aerial).
 After connecting the FM...

Getting Started
17 GB
Tip
If you have poor FM reception, use an “L” type 75-ohms 
coaxial cable (not supplied) to connect the system to an 
outdoor FM antenna (aerial) as shown below. If you use a 75-
ohms coaxial cable other than “L” type, you may not be able 
to replace the covers properly. 5: Switching on the 
system
Install this system so that the power cord can be 
unplugged from the wall socket immediately in the 
event of trouble.
1Connect the system to your mains socket 
(220-240V AC, 50Hz)....

18 GB
6: Auto-tuning the TV
After switching on the system, a message confirming 
the system start auto-tuning appears on the screen.
You must tune the system to receive channels (TV 
broadcasts). Do the following to search and store all 
available channels.
1Press   (OK) to select [Yes].
The system starts searching for all available 
digital channels, followed by all available 
analogue channels. This may take some time, 
please be patient and do not press any buttons on 
the system or remote.
Once all...

Getting Started
19 GB
7: Selecting the DVD 
language (Quick Setup)
You can set the display language.
1Press DVD (direct input select) to switch 
the input to DVD.
[Press [ENTER] to run QUICK SETUP.] appears 
at the bottom of the screen. This message does not 
appear if the disc is loaded or Quick Setup is 
already done.
2Press   (ENTER) without inserting a 
disc.
The Setup Display for selecting the language used 
in the on-screen display appears.
3Press M/m to select a language.
The system displays the...

20 GB
Watching TV
1Press 1 on the system to switch on the 
system.
When the system is in standby mode (the 1 
(standby) indicator on the system is red), press 
"/1 on the remote to switch on the system.
2Press DIGITAL to switch to digital mode 
or ANALOG to switch to analogue mode.
The channels available vary depending on the 
mode.
3Press the number buttons or PROG
 +/– to select a TV channel.
To select channel numbers 10 and above using the 
number buttons, enter the second and third digits 
within...