Sony Tav L1 Operating Instructions

							11 GB
xAuto input select button F
While the input is except DVD, if you press Z on the 
system or H, the input will be changed to DVD 
automatically.
This system has various types of menus:
 TV: TV MENU
 DVD: DVD MENU
DVD TOP MENU
DVD DISPLAY
 FM: FM MENU
 These menus are available when either input is 
selected.
 TV/DVD/FM: AMP MENU
xCURSOR MODE buttons B
When one of these buttons lights up, you can operate 
its menu (
						

							
12 GB
1/  – Input select/Text hold
 In TV mode (page 25): Selects the input source  from equipment connected to the system.
 In Text mode (page 21): Holds the current page.
 In TV/DVD/FM mode (page 10): Switches the  input source.
 – Lift up/down (page 71)
" /1  – On/standby (page 20)
Switches off the system temporarily. The  1 
(standby) indicator on the system (front of the lift 
unit) lights up. Press again to switch on the system 
from the standby mode.  – Sleep timer (page 42)
3 Number buttons
 In TV mode: Selects channels. For channel 
numbers 10 and above, enter the second digit 
within two seconds.
 In Text mode: Enters the three digit page number  to select the page.
 In DVD mode: Selects the item, title, chapter,  etc. Enters the password and area code.
 In FM mode: Selects the preset number.  The number 5 button has a tactile dot.*
9   – Next/Previous +/– (page 30)
X  – Pause (page 30)
H  – Play (page 30)
The 
H  button has a tactile dot.*
,   – Replay, Advance, Step 
(page 30)
m /,  M/  – Scan, Slow +/– (page 33)
x  – Stop (page 30)
qd AMP MENU (page 70)
qg ANGLE (page 34) 
AUDIO (page 31)
The AUDIO button has a tactile dot.*
PICTURE NAVI (page 33) 
REPEAT (page 58)
SA-CD/CD (page 32)
SUBTITLE (page 34)
TIME/TEXT (page 54) 
qk O RETURN (page 32)
ql DVD TOP MENU (page 49)
w; CLEAR (page 53)
ws DVD (direct input select) (page 10)
2 FM (CURSOR MODE) (page 11)
5 FM (direct input select) (page 10)
qa m /,  M/  – Tuning (page 36) 
qs PROG +/– (page 35)
The PROG + button has a tactile dot.*
qd FM MENU (page 36)
* Use the tactile dot as a reference when operating the system. 
Common operations
To control the TV
To control the DVD
To control the FM tuner
 
						

							13 GB
Overview of the system/
lift unit buttons and 
indicators
Touch panel buttons (2 – 9): Touch any of these 
buttons once, to activate the panel (buttons light up), then 
touch the desired button.
1Disc slot
2Z – Eject
Eject a disc.
3H – Play
Play a disc.
4x – Stop
Stop a disc.52 +/– – Volume
Increases (+)/decreases (–) volume.
6PROG +/–
 In TV mode: Select next (+)/previous (–) 
channel.
 In FM mode: Select next (+)/previous (–) preset 
station.
7FM
Change input select to FM directly.
8TV
Change input select to TV directly.
9 – Input select
Select the input select of connected equipment.
Each time you press the button, the input select 
changes as below.
A-TV t D-TV t AV1 t AV2 t DVD t 
AV4 t PC t HDMI t A-TV t D-TV 
t........
0 UP/DOWN – Lift unit up/down
Move the lift unit up/down.
qa1 – Standby
Switch system on/off. While the system is on, if 
you press "/1 on the remote, the system enters 
standby mode. 
qs` – Power indicator
Lights green when system is on.
qd1 – Standby indicator
Lights red when system is in standby mode.
qf – Picture Off (page 41)/Timer indicator 
(page 42)
 Lights up in amber when the “Sleep Timer” is 
set or when a digital event is programmed.
 Lights up in green when “Picture Off” is set.
 Lights up in red when digital REC starts.
qgFront panel display (page 69)
qhSound Field indicator
qj – Remote control sensor
qkLift unit
2CH STEREO AUTOFRONT
SURROUND
TV TVUP/DOWN UP/DOWN
FM FM PROG
PROG
qsqdqf 1qg
qk
qjqh
0qa84265379
 
						

							
14 GB
1: Checking the 
accessories
Remote RM-ANU005 (1)
Size AA batteries (R6 type) (2)
AC power cord (mains lead) (1)
Screws (2)
FM wire antenna (aerial) (1)
Frame grille (1)
Quick Start Guide (1)
2: Inserting batteries 
into the remote
Notes
 Observe the correct polarity when inserting batteries.
 Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of the battery. 
Please consult your local authority.
 Do not use different types of batteries together or mix old  and new batteries.
 Handle the remote with care. Do not drop or step on it, or 
spill liquid of any kind onto it.
 Do not place the remote in a location near a heat source, or  in a place subject to direct sunlight, or in a damp room.
Getting Started
 
						

							
Getting Started
15 GB
3: Connecting a TV aerial/VCR/DVD player
1Remove the covers.
When all connections have been made, replace the 
covers.
2Connect your aerial to the   socket on 
the rear of the system.
If connecting to an aerial only
Go to step 4.
3Connect your VCR/DVD player.
1Connect the   socket on the rear of the 
system to the input socket on your VCR with 
the RF lead.
2 Connect the scart socket on your VCR/DVD 
player to the  / 1 or 2 scart socket on 
the rear of the system with a scart lead.
4Connect the supplied AC power cord 
(mains lead) to the AC IN socket on the 
rear of the system.
Note
Do not connect the AC power cord (mains lead) to your 
mains socket until all connections are complete.
To prevent the system from toppling over
Notes
 Be sure to take measures to prevent the system from 
toppling over. If you fail to do so, the system may topple 
over and cause injury. Anchor the system to a wall, pillar, 
etc., to prevent it from toppling over.
 Any wall alternations (drilling, etc.) are your own  responsibility.
Prepare a commercially available strong rope or chain 
and wall anchor bracket beforehand.
1Remove the two small screws, and then 
attach the two large screws to the screw 
holes on the rear of the system.
(SmartLink)12 5 PC
IN
OUT
Rear of the system AC power cord 
(mains lead) 
(supplied)
Coaxial cable 
(not supplied) Scart lead (not supplied)
VCR
RF lead (not supplied)
Scart lead (not supplied) DVD player
1
2
Continued
 
						

							16 GB
2Secure the wall anchor bracket to a wall 
or pillar.
3Thread the rope or chain through both 
holes of the screws, and then tighten the 
other end of the rope or chain to the wall 
anchor bracket.
4: Connecting the FM 
wire antenna (aerial)
Connect the supplied FM wire antenna (aerial) for 
listening to the FM radio. Thread the wire antenna 
(aerial) through the slit of the cover, and then replace 
the cover. 
Notes
 Be sure to fully extend the FM wire antenna (aerial).
 After connecting the FM wire antenna (aerial), keep it as 
horizontal as possible.
A commercially 
available wall 
screw A commercially available 
strong rope or chainDVD
DIGITAL OUTFM ANTENNA
OPTICALFM 75
COAXIAL
FM wire antenna (aerial)
 
						

							Getting Started
17 GB
Tip
If you have poor FM reception, use an “L” type 75-ohms 
coaxial cable (not supplied) to connect the system to an 
outdoor FM antenna (aerial) as shown below. If you use a 75-
ohms coaxial cable other than “L” type, you may not be able 
to replace the covers properly. 5: Switching on the 
system
Install this system so that the power cord can be 
unplugged from the wall socket immediately in the 
event of trouble.
1Connect the system to your mains socket 
(220-240V AC, 50Hz).
2Press 1 on the system (top of the lift 
unit).
When you switch on the system for the first time, 
a message confirming the system start auto-tuning 
appears on the screen, then go to “6: Auto-tuning 
the TV” (page 18).
When the system is in standby mode (the 1 
(standby) indicator on the system is red), press 
+/1 on the remote to switch on the system.
Notes
 Depending on the Lift Mode setting or selected input, 
the lift unit will move down when turning on the 
system.
 To recall from standby mode by pressing 1 on the 
system, press 1 to turn off the system, and then press 
and hold 1 again until ` (power indicator) lights up in 
green.
To save the power in standby mode
Press "/1 on the remote while the system turns on. To 
cancel standby mode, press "/1 once.
DVD
DIGITAL OUTFM ANTENNA
OPTICALFM 75
COAXIAL
Outdoor FM antenna 
(aerial)
“L” type 75-ohms coaxial 
cable (not supplied)
1AC power cord 
(mains lead)
Continued
 
						

							18 GB
6: Auto-tuning the TV
After switching on the system, a message confirming 
the system start auto-tuning appears on the screen.
You must tune the system to receive channels (TV 
broadcasts). Do the following to search and store all 
available channels.
1Press   (OK) to select [Yes].
The system starts searching for all available 
digital channels, followed by all available 
analogue channels. This may take some time, 
please be patient and do not press any buttons on 
the system or remote.
Once all available digital and analogue channels 
have been stored, the system returns to normal 
operation, displaying the digital channel stored on 
channel number 1. If no digital channels are 
found, the analogue channel stored on channel 
number 1 is displayed.
When a message appears for you to confirm the 
aerial connections
No digital or analogue channels are found. Check 
all the aerial connections and press   (OK) to 
start auto-tuning again.
2The Programme Sorting menu appears 
on the screen.
Note
If some digital channel is found, this step will not 
appear.
3To change the order in which the 
channels are stored on the system. See 
page 44.
4Press TV MENU to exit.
The system has now tuned in all the available 
channels.
Hint
To stop Digital Auto Tuning, select [Cancel]. Digital 
Auto Tuning is cancelled, and Analogue Auto Tuning 
starts.
 (OK)
TV MENU
Do  you  want  to  start
automatic  tuning ?
Ye sNo
m
Number  of  Services  found14
Searching.         40%
Cancel:
Digital auto-tune display
m
Auto  Tuning
Programmes found:
5
Searching...
Analogue auto-tune display
 
						

							Getting Started
19 GB
7: Selecting the DVD 
language (Quick Setup)
You can set the display language.
1Press DVD (direct input select) to switch 
the input to DVD.
[Press [ENTER] to run QUICK SETUP.] appears 
at the bottom of the screen. This message does not 
appear if the disc is loaded or Quick Setup is 
already done.
2Press   (ENTER) without inserting a 
disc.
The Setup Display for selecting the language used 
in the on-screen display appears.
3Press M/m to select a language.
The system displays the on-screen display, the 
menu and subtitles in the selected language.
Note
The selectable language is different depending on the 
area.
4Press  (ENTER).
Quick Setup is finished. All connections and setup 
operations are complete.
To quit the Quick Setup
Press DVD DISPLAY in any step.
To recall the Quick Setup display
1Press DVD DISPLAY. (If a disc is playing, press x to 
stop playback, then press DVD DISPLAY.)
The Control Menu appears.
2Press M/m to select   [SETUP], then press 
 (ENTER).
The options for [SETUP] appear.
3Press M/m to select [QUICK], then press   
(ENTER).
The Quick Setup display appears.M/m/ (ENTER)
DVD
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ITALIANOESPAÑOLNEDERLANDS
DANSK
SVENSKA FRANÇAISENGLISH
ENGLISH
DEUTSCH
1 2 ( 
2 7 )
QUICK
RESET
DVD VIDEO           :      : 1 8 ( 
3 4 )
CUSTOMQUICK
 
						

							20 GB
Watching TV
1Press 1 on the system to switch on the 
system.
When the system is in standby mode (the 1 
(standby) indicator on the system is red), press 
"/1 on the remote to switch on the system.
2Press DIGITAL to switch to digital mode 
or ANALOG to switch to analogue mode.
The channels available vary depending on the 
mode.
3Press the number buttons or PROG
 +/– to select a TV channel.
To select channel numbers 10 and above using the 
number buttons, enter the second and third digits 
within two seconds.
To select a digital channel using the Digital 
Electronic Programme Guide (EPG), see page 22.
In digital mode
An information banner appears briefly. The 
following icons may be indicated on the banner. 
Additional operations
Watching TV
1
1
"/1
Number 
buttons
DIGITAL
ANALOG
PROG +/–
: Interactive service is available (MHEG Digital 
Text)
: Interactive service (MHEG Digital Text) is 
currently disabled
: Radio service
: Scrambled/Subscription service
: Multiple audio languages available
: Subtitles available
: Subtitles available for the hearing impaired
: Recommended minimum age for current 
programme (from 4 to 18 years)
: Parental Lock
: Current programme is being recorded
To D o  t h i s
Turn off the system 
temporarily 
(Standby mode)Press "/1 on the remote.
Turn off the system 
completelyPress 1 on the system.
Adjust the volume Press 2 + (increase) 
/– (decrease).