Sony Projector Vpl Hs1 User Manual

31 GB Projecting a Selected Picture When the Power Is Turned On — Startup
Using a “Memory 
Stick”
3Press M, m, < or , to select 
the picture you want to use as 
the startup picture, and press 
ENTER.
The Index menu appears.
4Press M or m to select “Str. 
up,” and press ENTER.
5Press M or m to select “Entry,” 
and press ENTER.
The startup mark is displayed in the Index menu.
You can register one picture used for the startup 
picture, per one “Memory Stick.”
Setting the Startup Picture
1Select MS by...

GB 32Deleting a Still Picture
Using a “Memory 
Stick”
4Press M or m to select the item 
used for startup picture, and 
press ENTER.
Original: Select to use the original picture 
stored in the projector. This is the factory 
setting.
Custom: Select to use the picture registered in 
the index screen and stored in the “Memory 
Stick.” (1 page 30)
Off: Select when you do not set the startup.
Notes
When you want to clear the startup screen while displaying it, 
press M/m/

33 GB Initializing a “Memory Stick”
Using a “Memory 
Stick”
Initializing a 
“Memory Stick” 
When a “Memory Stick” cannot be used, initialize it 
by the projector.
All the data stored in a “Memory Stick” is cleared 
when the “Memory Stick” is initialized.
1Select MS by pressing the 
INPUT button to display the 
MS home. (1
11 1 page 24)
2Press M or m to select  
MEMORY STICK , and press 
ENTER.
3Press ENTER again.
4Press M or m to select 
“Execute,” and press ENTER.
5Press M to start initializing.
To...

GB 34Troubleshooting
Others
Others
This section describes how to solve the problems, how to 
replace a lamp and air filter, etc.
Troubleshooting
Symptom Cause and Remedy
The power is not turned on.The power has been turned off and on with the [/ 1 (on/standby) switch at a 
short interval.
cWait for about one minute before turning on the power (1 page 15).
The lamp cover is detached.
cClose the lamp cover securely (1 page 38).
The air filter cover is detached.
cClose the air filter cover securely (1...

35 GB Troubleshooting
Others
The picture flickers.DOT PHASE in the INPUT SETTING   menu has not been adjusted 
properly.
cAdjust DOT PHASE in the INPUT SETTING   menu properly (1 page 
19).
On-screen display does not appear.STATUS in the SET SETTING   menu is set to OFF.
cSet STATUS in the SET SETTING   menu to ON (1 page 20).
No sound.Cable is disconnected or the connections are wrong.
cCheck that the proper connections have been made (1 pages 8 and 9).
VOLUME setting is not correct.
cAdjust VOLUME...

GB 36Troubleshooting
Others
Indicators
The LAMP/COVER or TEMP/FAN indicator on the control panel lights up or flashes if there is any trouble with 
your projector.
Warning Messages
Use the list below to check the meaning of the messages displayed on the screen.Indicator Meaning and Remedy
LAMP/COVER flashes.The lamp cover or the air filter cover is detached.
cAttach the cover securely (1 pages 38 and 39).
LAMP/COVER lights 
up.The lamp has reached the end of its life.
cReplace the lamp (1 page 38)....

37 GB Troubleshooting
Others
Caution Messages
Use the list below to check the meaning of the messages displayed on the screen.
Caution displays while you are using the “Memory Stick”
When the following display appears on the screen, you cannot use this “Memory Stick.” Use another one.
Message Meaning and Remedy
NO INPUTNo input signal
cCheck connections (1 page 8).
Not applicable!You have pressed the wrong button.
cPress the appropriate button.
File errorIn the sub menu for selecting the contents when...

GB 38Replacing the Lamp
Others
Replacing the 
Lamp
The lamp used for the light source has a certain life. 
When the lamp dims, the color balance of the picture 
becomes strange, or “Please replace the LAMP.” 
appears on the screen, the lamp is exhausted. Replace 
the lamp with a new one (not supplied).
Use LMP-H120 Projector Lamp as the replacement lamp.
When replacing the lamp after using the 
projector
Turn off the projector, then unplug the power cord. 
Wait for at least an hour for the lamp to cool....

39 GB Replacing the Air Filter
Others
Notes
Do not put your hands into the lamp replacement spot, or not 
fall any liquid or object into it to avoid electrical shock or fire.
Be sure to use the LMP-H120  Projector Lamp for replacement. 
If you use lamps other than LMP-H120, the projector may 
cause a malfunction.
Be sure to turn off the projector and unplug the power cord 
before replacing the lamp.
Disposal of used projector lamp
As the materials used in this lamp are similar to those 
of a...

GB 40Specifications
Others
Specifications
System
Projection system
3 LCD panels, 1 lens, projection 
system
LCD panel 0.7-inch TFT LCD panel, 
1,440,000 pixels (480,000 
pixels × 3)
Lens 1.3 times zoom lens (manual) 
Lamp 120 W UHP type
Projection picture size
Range: 40 to 150 inches (measured 
diagonally)
Color system NTSC
3.58/PAL/SECAM/NTSC4.43/
PAL-M/PAL-N system, 
switched automatically/
manually
Acceptable video signals
15k, DTV (480i/480p/1080i/720p)
Acceptable computer signals
fH: 19 to 72 kHz...