Sony Projector Vpl Fw300l User Manual

ƒ”
GO11 

Table of Contents13 
Table of Contents
Precautions ........................................................... 14
Overview ............................................................... 15
Attaching a Lens  .................................................. 16
Attaching a Lens ............................................... 16
Replacing the Lens  ........................................... 17
Installing the HD-SDI/SDI Input Adaptor ........ 17
Installation Diagram...

Precautions 14
Precautions
On safety
• Check that the operating voltage of your unit is 
identical with the voltage of your local power supply. 
If voltage adaptation is required, consult with 
qualified Sony personnel.
 Should any liquid or solid object fall into the cabinet, 
unplug the unit and have it checked by qualified Sony 
personnel before operating it further.
 Unplug the unit from the wall outlet if it is not to be 
used for several days.
 To disconnect the cord, pull it out by the plug. Never...

Overview15 
On cleaning the lens
The lens surface is especially treated to reduce reflection 
of light.
As incorrect maintenance may impair the performance 
of the projector, take care with respect to the following:
 Avoid touching the lens. To remove dust on the lens, 
use a soft dry cloth. Do not use a damp cloth, detergent 
solution, or thinner.
 Wipe the lens gently with a soft cloth such as a 
cleaning cloth or glass cleaning cloth.
 Stubborn stains may be removed with a soft cloth such 
as a...

Attaching a Lens 16
Attaching a Lens
The projector comes from the factory with no lens 
attached. You can attach the following types of optional 
lenses to the projector:
 VPLL-Z4019 Standard Zoom Lens
 VPLL-4008 Fixed Short Focus Lens (for rear 
projection, optical axis angle 0 degrees))
 VPLL-Z4015 Short Focus Zoom Lens
 VPLL-Z4025 Middle Focus Zoom Lens
 VPLL-Z4045 Long Focus Zoom Lens
Attaching a Lens
Follow the steps below to attach a lens:
For details on the lens, also refer to the operating...

Installing the HD-SDI/SDI Input Adaptor17 
6Replace the lens cover.
Align the two tabs with the slots, place the lens 
cover over the lens, then tighten the two screws at 
the bottom.
Note
Move the lens fixing lever completely downward. 
Otherwise you cannot lock the lens.
Replacing the Lens
The procedure for replacing the lens is the same as that 
for “Attaching a Lens.” Perform steps 1 to 3 to unlock 
the lens fixing lever, and withdraw the lens straight 
forward. Then perform steps 4 to 6 to attach...

Installation Diagram 18
Note on BKM-FW16 HD-SDI/SDI Input 
Adaptor
When a 2K × 1K (2048 × 1080) signal is input, 
information of a vertical line at both ends is not 
displayed. The signal being displayed is not native. 2K 
× 1K equivalent.
Specifications of 2K × 1K signal
Installation Diagram
This section gives projector installation examples 
according to the installation location, lens and display 
size.
For the installation diagrams and dimension tables, see 
pages 66 to 82.
Floor Installation (A and...

Installation Diagram19 
Ceiling Installation (C and D on 
page 70)
This section gives examples for installing the projector 
on the ceiling. 
When installing the projector on the ceiling, use the 
optional PSS-630 Projector Suspension Support.
For ceiling installation, consult with qualified Sony 
personnel only.
Note on the dust cover
When installing the projector on the ceiling, be sure to 
attach the supplied dust cover to the projector.
Fix the dust cover to the ceiling bracket mounting holes 
of the...

Table des matières20
Table des matières
Précautions ........................................................... 21
Aperçu .................................................................. 22
Montage d’un objectif  ......................................... 23
Montage d’un objectif  ...................................... 23
Remplacement de l’objectif  ............................. 24
Installation de l’adaptateur d’entrée 
HD-SDI/SDI ......................................................... 24
Schéma...