Sony Projector Qualia 004 User Manual

6061
Installing the projector (continued)
Ceiling installation
When installing the projector on the ceiling, 
use the PSS-100 projector suspension 
support.
For set up of your QUALIA 004, please 
consult with an authorized Sony custom 
installer.
You can calculate the throwing distance 
between the screen and the lens (TD) using 
the chart or formula on page 63.
TD:Distance between the screen and the center of the lensV:Height of the screen
Center of the screen
Center of the lens
PSS-100 projector...

6263
�������
������������������
���������
������
����������
������
����������
����������������
Center of the supporting shaft Projector mount bracket 
Center of the screen
Center of the lens
Attaching the PSS-100 projector suspension 
support 
For set up of your QUALIA 004, please 
consult with an authorized Sony custom 
installer.
Installing the projector (continued)
�������������
���������������������������������
Center of the lens
Front side of the projector
Top view
Side viewFront view
Distance...

6465
������������������������������������������������
�������������������
Connections
Component equipment such as an AV amplifier, VCR, tuner, etc.
AV amplifier,VCR, tuner, etc.VCR, etc.
Connector panel (Left side)
Computer
Notes on connections
When making connections, be sure to do the following:
• Tur n off all equipment before making any connections.
• Use the proper cables for each connection.
• Insert the cable plugs properly; plugs that are not fully inserted often generate noise. When pulling out...

6667
�����������
��������������������������������
Connections (continued)
Connector panel (Right side)1 HDMI connector   
Connect to the HDMI output of your 
component with an HDMI connector.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
2 DVI-D connector
Connect to the DVI-D output of your 
component with a DVI-D connector. 
3 TRIGGER jack (monaural minijack)
Connect to send the ON or OFF condition of 
the projector to exter...

6869
Operating the projector 
from a computer 
Accessing the projector from a 
computer
You can check the present status of the 
projector on a computer display and control 
the projector from a computer. Also, the 
projector enables the sending of mail that 
contains messages on the time for 
replacement of the projector lamp, error 
occurrences, etc., to mail addresses that 
have been specified.
Confirm that the projector and computer are 
connected to the router/hub with the LAN 
cables, then tur n on...

7071
Operating the projector 
from a computer (continued)
Setting the date and time
Click “Date and T ime.”
This setting is required for the Regular 
Report function.
Time Zone
Select the region in which you are using the 
projector.
Date/Time
Set the date and time.
Time Server
Enter the address of the time server when 
the time is set by a time server.
Network settings
Click “Network.”
Internet Protocol (TCP/IP)
Normally, set “Obtain an IP address 
automatically (DHCP).” If you select “Specify 
an IP...

7273
Operating the projector 
from a computer (continued)
Address field
Address
Enter the e-mail addresses where you want 
the e-mail messages to be sent in each text 
box. The projector allows you to send e-mail 
to 4 different addresses. You can enter up to 
64 characters for each address.
Report Timing
Regular:
Select this check box to arrange the 
sending of the Regular Report.
Maintenance:
Select this check box to arrange the 
sending of an e-mail message that 
informs you of the number of hours the...

7475
Maintenance
Replacing the lamp/air filter
When the lamp begins to dim, replace it 
promptly with a new one. Contact QUALIA 
Customer Service to replace the lamp.
The message “Please replace the 
Lamp/Filter.” is displayed when the remaining 
life of the lamp and the air filter reaches 
about 50 to 15 hours, and then again near 
the end. The lamp automatically tur ns off 
about one minute after it reaches the end of 
its life. 
The lamp and the air filter should be replaced 
when a war ning message...

7677
Maintenance
Troubleshooting
If the projector appears to be operating 
erratically, follow the procedures outlined 
below.
1 Try to diagnose and correct the problem 
using the troubleshooting guide on page 
76 to  81.
2 If the problem still persists, contact QUALIA 
Customer Service.
 QUALIA Customer Service
Toll-free number:
1-877-782-5423
Power
SymptomCause/Remedy
The power does not turn on.
• If any message appears on the information panel display, contact QUALIA Customer Service.
• Make sure that...

7879
Maintenance
Troubleshooting (continued)
Remote
SymptomCause/Remedy
The remote does not work.
• There are no batteries in the remote. Install batteries (see page 24).
• The remote batteries are used up. Replace all of them with new ones, taking care to match the polarities (see page 24).
• The remote control cable is not connected to the CONTROL S IN connector (projector) or CONTROL S OUT (remote). Connect the remote control cable to both the projector and remote, or disconnect the cable.
• The...