Sony Projector Qualia 004 User Manual

2021
Control panel 
Identification of parts (continued)
687
243
5
1
Location of the control panel
The control panel is located on the rear of the projector as shown below. 
1 ?/1 (on/standby) button
Tur ns the projector on when the projector is 
in the standby mode.
To tur n off the projector, press the ?/1 
button twice or press and hold the ?/1 
button for about one second according to 
the indications on the screen. 
For details on steps for tur ning off the power, 
see “To tur n off the power” on...

2223
1 PICTURE MUTING button
Tur ns off the picture. Press 
again to restore the picture.
2 INPUT buttons 
Select the input signal.
VIDEO:
For the video signal of 
equipment connected to the 
projector’s VIDEO jack.
S VIDEO:
For the video signal of 
equipment connected to the 
projector’s S VIDEO jack.
A:
For the video signal of 
equipment connected to the 
projector’s INPUT A 
connectors.
B:
For the video signal of 
equipment connected to the 
projector’s INPUT B 
connectors.
DVI:
For the video signal...

2425
Inserting batteries 
1 Tur n the screw counterclockwise using a coin, etc. to open the lid.
2 Insert the four size AAA (R03) batteries (supplied), taking care to match the 
polarities as shown below.
Identification of parts (continued)
3 Replace the lid, then tur n the screw clockwise to lock the lid.
Be sure to insert the batteries from the # side first.
Tur n clockwise.
Notes on batteries
• Make sure that the battery polarity (orientation) is correct when inserting batteries.
• Do not mix an old...

2627
Projecting images
1 Press the ?/1 button on the remote or on the control panel to tur n the projector 
on.
2 Tur n on any equipment connected to the projector. 
3 Press the INPUT button to select the input source. 
INPUT-AComponent equipment connected to the INPUT A connector on the projector
INPUT-BEquipment connected to the INPUT B connector on the projector
DVIVideo equipment connected to DVI-D connector on projector
HDMIVideo equipment connected to HDMI connector on the projector
VIDEOVideo...

2829
Selecting the screen projection mode
You can enjoy various screen projection 
modes according to the video signal 
received. For details on the available video 
signals, see page 42. 
For details on operating the menu screen, 
see “Using the menu” on page 30.
1 Press the MENU button.
The menu display appears.
2 Press the M or m button to select the 
INPUT SETTING menu, then press the , 
or ENTER button.
3 Press the M or m button to select “W ide 
Mode,” then press the , or ENTER 
button....

3031
3 Use the M or m button to select an item, then press the , or ENTER button. 
The settings appear in a pop-up window 
or are displayed in the next level.
In a pop-up window
�������
������������������������������������������������
����������������
��������������
���������������������������
MenusSettings
In the next level
��������������������������������������������������������������������������������������������������������������������������������������������������������������������
��������������...

3233
PICTURE SETTING menu
PICTURE MODE
You can select the picture mode that best 
suits the type of program or your 
room’s conditions.
Dynamic:
Select this for enhanced picture contrast and 
sharpness.
Standard:
Recommended for normal viewing conditions 
in your home. Select this if you encounter 
roughness when viewing the picture with 
“Dynamic.”
Cinema:
Select this for a soft, film-like picture.
User1, User2, User3:
Adjust the quality of the picture to suit your 
taste. The settings will be stored in...

3435
PICTURE SETTING menu
(continued)
Color Temp
Adjusts the color temperature.
High:
Select to make the whites bluish.
Middle:
Select to set the color temperature between 
“High” and “Low.”
Low:
Select to make the whites reddish.
Custom1, Custom2, Custom3:
Adjust the color temperature to suit your 
taste. The settings will be stored in a 
pre-selected memory area of the projector.
I/P Mode
Smooths out video images that look rougher 
as the size increases.
DRC Progressive:
Select to convert an interlace...

3637
INPUT SETTING menu
ADJUST SIGNAL
The INPUT SETTING menu is used to adjust 
the input signal.
Items that cannot be adjusted for a particular 
input signal do not appear in the menu.
Example: When a computer signal is input.
Dot Phase
Adjusts the dot phase of the panel and the 
computer signal input from the INPUT B 
connector.
Adjust the picture to the point where it looks 
clearest.
H Size 
Adjusts the horizontal size of the picture 
input from the INPUT A/B connector. 
The higher the setting, the...

3839
INPUT SETTING menu (continued)
You can also select the desired screen 
projection mode manually. Each time you 
press the WIDE MODE button on the remote, 
the “W ide Mode” setting changes cyclically 
as follows: “Full,” “Normal,” “W ide Zoom,” 
“Zoom,” “Subtitle.”
Screen projection mode when “Auto Wide 1” or “Auto Wide 2” is set
(depending on the type of picture)
Type of pictureScreen projection mode
Auto Wide 1Auto Wide 2
Normal TV broadcastThe image is displayed according to the screen projection...