Sony Projector MP-CL1 User Manual
Here you can view all the pages of manual Sony Projector MP-CL1 User Manual. The Sony manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
![Page 21
To revert to the default values
Select [Initialize] ().
MP-CL1 3-MP0-107-01](http://img.usermanuals.tech/thumb/72/100156/w300_projector_manual_8999_d-20.png "Page 21
To revert to the default values
Select [Initialize] ().
MP-CL1 3-MP0-107-01")
To revert to the default values Select [Initialize] (). MP-CL1 3-MP0-107-01
Page 22
![Page 22
Biphase alignment
Adjust the synchronization timing of the input signals if the projected image is
flickering or blurred. If the three white vertical lines at the center of the [Biphase
alignment] screen look blurred, you need to perform the following procedures.
1 Select [ Setup] - [ Biphase alignment].
The [Biphase alignment] screen appears. To select
an item on the screen, slide the Jog Lever to + or
−, and then press the lever with the desired item
highlighted.
Init ializ e
SaveToF actor y
2...](http://img.usermanuals.tech/thumb/72/100156/w300_projector_manual_8999_d-21.png "Page 22
Biphase alignment
Adjust the synchronization timing of the input signals if the projected image is
flickering or blurred. If the three white vertical lines at the center of the [Biphase
alignment] screen look blurred, you need to perform the following procedures.
1 Select [ Setup] - [ Biphase alignment].
The [Biphase alignment] screen appears. To select
an item on the screen, slide the Jog Lever to + or
−, and then press the lever with the desired item
highlighted.
Init ializ e
SaveToF actor y
2...")
Biphase alignment Adjust the synchronization timing of the input signals if the projected image is flickering or blurred. If the three white vertical lines at the center of the [Biphase alignment] screen look blurred, you need to perform the following procedures. 1 Select [ Setup] - [ Biphase alignment]. The [Biphase alignment] screen appears. To select an item on the screen, slide the Jog Lever to + or −, and then press the lever with the desired item highlighted. Init ializ e SaveToF actor y 2...
Page 23
![Page 23
5 Select [Close] ().
The [Biphase alignment] screen closes.
To revert to the most recently saved value
Select [Cancel] ().
To revert to the default values
Select [Initialize] ().
MP-CL1 3-MP0-107-01](http://img.usermanuals.tech/thumb/72/100156/w300_projector_manual_8999_d-22.png "Page 23
5 Select [Close] ().
The [Biphase alignment] screen closes.
To revert to the most recently saved value
Select [Cancel] ().
To revert to the default values
Select [Initialize] ().
MP-CL1 3-MP0-107-01")
5 Select [Close] (). The [Biphase alignment] screen closes. To revert to the most recently saved value Select [Cancel] (). To revert to the default values Select [Initialize] (). MP-CL1 3-MP0-107-01
Page 24
![Page 24
Troubleshooting
Operation
This product does not charge.
• The USB OUT jack can only be used to supply power to other devices, and it
cannot be used to charge this product. Be sure to use the Micro USB jack to
charge this product.
The fan is noisy.
• This is not a malfunction. When the ambient temperature is high, the fan noise
becomes louder.
No images are projected.
• Check that the input source is selected correctly in the [
Input change] menu.
• Check that the cable, connector and/or...](http://img.usermanuals.tech/thumb/72/100156/w300_projector_manual_8999_d-23.png "Page 24
Troubleshooting
Operation
This product does not charge.
• The USB OUT jack can only be used to supply power to other devices, and it
cannot be used to charge this product. Be sure to use the Micro USB jack to
charge this product.
The fan is noisy.
• This is not a malfunction. When the ambient temperature is high, the fan noise
becomes louder.
No images are projected.
• Check that the input source is selected correctly in the [
Input change] menu.
• Check that the cable, connector and/or...")
Troubleshooting Operation This product does not charge. • The USB OUT jack can only be used to supply power to other devices, and it cannot be used to charge this product. Be sure to use the Micro USB jack to charge this product. The fan is noisy. • This is not a malfunction. When the ambient temperature is high, the fan noise becomes louder. No images are projected. • Check that the input source is selected correctly in the [ Input change] menu. • Check that the cable, connector and/or...
Page 25
![Page 25
The lamp blinks in red while charging another device via the USB OUT
jack.
• The battery of this product is almost depleted.
• The USB cable (supplied) may not be connected correctly. Disconnect it and
reconnect.
• The specifications of the connected device may not meet the requirements.
Check the charging specifications of the device.
Picture
The image is flickering or blurred.
• The synchronization timing of the input signals may need to be adjusted. Select
[
Setup] - [ Biphase alignment]...](http://img.usermanuals.tech/thumb/72/100156/w300_projector_manual_8999_d-24.png "Page 25
The lamp blinks in red while charging another device via the USB OUT
jack.
• The battery of this product is almost depleted.
• The USB cable (supplied) may not be connected correctly. Disconnect it and
reconnect.
• The specifications of the connected device may not meet the requirements.
Check the charging specifications of the device.
Picture
The image is flickering or blurred.
• The synchronization timing of the input signals may need to be adjusted. Select
[
Setup] - [ Biphase alignment]...")
The lamp blinks in red while charging another device via the USB OUT jack. • The battery of this product is almost depleted. • The USB cable (supplied) may not be connected correctly. Disconnect it and reconnect. • The specifications of the connected device may not meet the requirements. Check the charging specifications of the device. Picture The image is flickering or blurred. • The synchronization timing of the input signals may need to be adjusted. Select [ Setup] - [ Biphase alignment]...
Page 26
![Page 26
The projected image is unclear.
• Go to the [
Optical alignment] and/or [ Biphase alignment] menu and
perform adjustment.
The image is too dark.
• Adjust [
Contrast] and [ Saturation] in the [ Picture setting] menu.
The color does not look appropriate.
• Adjust [
Hue] and [ Saturation] in the [ Picture setting] menu.
Connection
The image is not projected smoothly via screen mirroring.
• Check that the Wi-Fi antenna parts of this product and the connected device
are not covered by your hands,...](http://img.usermanuals.tech/thumb/72/100156/w300_projector_manual_8999_d-25.png "Page 26
The projected image is unclear.
• Go to the [
Optical alignment] and/or [ Biphase alignment] menu and
perform adjustment.
The image is too dark.
• Adjust [
Contrast] and [ Saturation] in the [ Picture setting] menu.
The color does not look appropriate.
• Adjust [
Hue] and [ Saturation] in the [ Picture setting] menu.
Connection
The image is not projected smoothly via screen mirroring.
• Check that the Wi-Fi antenna parts of this product and the connected device
are not covered by your hands,...")
The projected image is unclear. • Go to the [ Optical alignment] and/or [ Biphase alignment] menu and perform adjustment. The image is too dark. • Adjust [ Contrast] and [ Saturation] in the [ Picture setting] menu. The color does not look appropriate. • Adjust [ Hue] and [ Saturation] in the [ Picture setting] menu. Connection The image is not projected smoothly via screen mirroring. • Check that the Wi-Fi antenna parts of this product and the connected device are not covered by your hands,...
Page 27
• The Wi-Fi function of the device capable of screen mirroring may need to be turned off when using the screen mirroring function. Refer to the manual of your device for details. If the problem still persists after performing the suggested remedies, contact your nearest Sony dealer. MP-CL1 3-MP0-107-01
Page 28
Important information Notes on use • The USB OUT jack of this product is for output only. Do not connect this product to a USB jack of a computer or other device. Doing so may cause malfunction. • If the lens is not clean, wipe it with a soft cloth such as eyeglass cleaner cloth. • Do not use or store this product in a humid or dusty place. • Remove cables from this product after use or while not in use. • Check the connections of this product periodically to make sure dust does not...