Sony Projector MP-CL1 User Manual

							To revert to the default values
Select [Initialize] ().
MP-CL1 3-MP0-107-01  
						

							Biphase alignment
Adjust the synchronization timing of the input signals if the projected image is 
flickering or blurred. If the three white vertical lines at the center of the [Biphase 
alignment] screen look blurred, you need to perform the following procedures.
1 Select [ Setup] - [ Biphase alignment].
The [Biphase alignment] screen appears. To select 
an item on the screen, slide the Jog Lever to + or 
−, and then press the lever with the desired item 
highlighted.
Init ializ e
SaveToF actor y
2 Select [Adjust] ().
3 Slide the jog lever to + or − so the three lines () look clear without blur. 
Press the jog lever when you have finished adjusting.
4  Select [Save] () to save the new value.
MP-CL1 3-MP0-107-01  
						

							5 Select [Close] ().
The [Biphase alignment] screen closes.
To revert to the most recently saved value
Select [Cancel] ().
To revert to the default values
Select [Initialize] ().
MP-CL1 3-MP0-107-01  
						

							Troubleshooting
Operation
This product does not charge. 
• The USB OUT jack can only be used to supply power to other devices, and it 
cannot be used to charge this product. Be sure to use the Micro USB jack to 
charge this product.
The fan is noisy.  
• This is not a malfunction. When the ambient temperature is high, the fan noise 
becomes louder.
No images are projected.  
• Check that the input source is selected correctly in the [
 Input change] menu.
 
• Check that the cable, connector and/or adaptor are connected correctly for 
wired connection.
 
• Some image formats may not be available depending on the connected device 
or the connection method.
There is no sound.  
• Check the volume level of this product and the connected device.
MP-CL1 3-MP0-107-01  
						

							The  lamp blinks in red while charging another device via the USB OUT 
jack.
 
• The battery of this product is almost depleted.
 
• The USB cable (supplied) may not be connected correctly. Disconnect it and 
reconnect.
 
• The specifications of the connected device may not meet the requirements. 
Check the charging specifications of the device.
Picture
The image is flickering or blurred.
 
• The synchronization timing of the input signals may need to be adjusted. Select 
[
 Setup] - [ Biphase alignment] in the menu and adjust the timing.
The image is a trapezoidal shape.  
• Move this product to adjust the projection angle.
 
• Correct the distortion electronically in the [
 Keystone] menu.
The image is reversed.  
• Select [
 Flip (left-right)] in the menu to flip back the image.
MP-CL1 3-MP0-107-01  
						

							The projected image is unclear. 
• Go to the [
 Optical alignment] and/or [ Biphase alignment] menu and 
perform adjustment.
The image is too dark.  
• Adjust [
 Contrast] and [ Saturation] in the [ Picture setting] menu.
The color does not look appropriate.  
• Adjust [
 Hue] and [ Saturation] in the [ Picture setting] menu.
Connection
The image is not projected smoothly via screen mirroring.
 
• Check that the Wi-Fi antenna parts of this product and the connected device 
are not covered by your hands, etc.
 
• Remove obstacles between this product and the connected device, and place 
them closer to each other.
A connection via screen mirroring cannot be established.  
• Check that the Wi-Fi antenna parts of this product and the connected device 
are not covered by your hands, etc.
MP-CL1 3-MP0-107-01  
						

							 
• The Wi-Fi function of the device capable of screen mirroring may need to be 
turned off when using the screen mirroring function. Refer to the manual of 
your device for details.
If the problem still persists after performing the suggested remedies, contact 
your nearest Sony dealer.
MP-CL1 3-MP0-107-01  
						

							Important information
Notes on use
 
• The USB OUT jack of this product is for output only. Do not connect this product 
to a USB jack of a computer or other device. Doing so may cause malfunction.
 
• If the lens is not clean, wipe it with a soft cloth such as eyeglass cleaner cloth.
 
• Do not use or store this product in a humid or dusty place.
 
• Remove cables from this product after use or while not in use.
 
• Check the connections of this product periodically to make sure dust does not 
accumulate.
 
• The antenna is built in to this product. Do not cover the antenna part with your 
hands, as doing so may affect the communications quality.
 
• Do not place this product close to credit cards. Doing so may result in the loss 
of recorded data.
 
• Noise may be heard on nearby TVs, radios or tuners while using this product. If 
this happens, use this product away from these products.
 
• When charging this product while projecting images, the remaining battery 
power of this product may decrease depending on the usage environment.
MP-CL1 3-MP0-107-01