Sony Lmd 2050w Operating Instructions

Location and Function of Parts and Controls11 
*8 Only when an NTSC signal is input and no markers 
are displayed. Not displayed when the multi display 
is enabled.*9 The signal can only be selected in the main display 
(see “SUB INPUT SELECT” on page 27).
*10 When a BKM-244CC is installed, closed captions 
are displayed.
Rear/Bottom Panel
aa/? (power) switch
The power is turned on or off.
The monitor is turned on by pressing side ?.
bAC IN socket
Connect the supplied AC power cord.
cDC 24V IN connector...

Location and Function of Parts and Controls 12
Note
When inputting a video signal with the jitters, etc. 
the picture may be disturbed.  We recommend using 
the TBC (time base corrector).
OUT connector
Loop-through output of the IN connector.  Connect 
to the external sync input of video equipment to be 
synchronized with this unit.
When the cable is connected to this connector, the 
75-ohm termination of the input is automatically 
released, and the signal input to the IN connector is 
output from this...

Installing to the Rack (LMD-2050W only)13 
Installing to the Rack 
(LMD-2050W only)
You can attach the monitor to the rack after removing the 
stand.
1Put the monitor on a soft cloth with the surface of 
the LCD monitor downward.
2Slide and remove the arm cover of the stand.
3Remove  four screws.
4Remove the arm.
5Remove four screws to remove the stand 
attachment bracket.
6Attach the mounting bracket, then attach the unit to 
the rack with four screws.
Note
The screws are not supplied.  Prepare screws...

Adjusting the Height of the Stand 14
Adjusting the Height of 
the Stand
You can adjust the height of the monitor in four levels 
for the LMD-2050W and three levels for the LMD-
2450W by changing the position of the stand attachment 
bracket and the arm attachment position. Depending on 
the height, you can install the input adaptor with the 
stand attached to the monitor.
A and B in the following list indicate the screw holes 
shown in the illustrations in steps 2 and 4.
Height of the monitor
Unit: mm...

Connecting the AC Power Cord15 
These screws are used for each display at the factory.
Connecting the AC 
Power Cord
1Plug the AC power cord into the AC IN socket on 
the rear panel.  Then, attach the AC plug holder 
(supplied) to the AC power cord.
2Slide the AC plug holder over the cord until it locks.
To disconnect the AC power cord
Pull out the AC plug holder while pressing the lock 
levers.
– +– +– +– +– +– +– +– +– +– +– +– +
+
–
AC power cord AC  IN socket
AC plug holder (Supplied)
+
–
 

Installing the Input Adaptor / Selecting the Default Settings  16
Installing the Input 
Adaptor
Before installing the input adaptor, disconnect the power 
cord.
1Remove the panel of the optional input slot.
2Insert the input adaptor into the slot.
3Tighten the screws.
Selecting the Default 
Settings
When you turn on the unit for the first time after 
purchasing it, select the area where you intend to use this 
unit from among the options.
The default setting values for each area
P
A
RA
L
L
E
L
 R
EM
O
T...

Selecting the Default Settings17 
1Turn on the unit with the a/? (power) switch on the 
rear panel.
The SELECT SETTING screen appears.
2Press the + or – button to select the area where you 
intend to use the unit and press the ENTER button.
If you select either 1, 3 or 5
The confirmation screen is displayed.  Confirm the 
selected area.  When the setting is wrong, press the 
RETURN button to return to the previous screen.
If you select either 2 or 4
One of the following screens appears.  Press the 
+ 
or...

Selecting the Menu Language 18
Selecting the Menu 
Language
You can select one of seven languages (English, French, 
German, Spanish, Italian, Japanese, Chinese) for 
displaying the menu and other on-screen displays.
“ENGLISH (English)” is selected in the default setting.
The current settings are displayed in place of the x 
marks on the illustrations of the menu screen.
1Turn on the unit.
2Press the CONTROL button.
The operation buttons are displayed.
3Press the MENU button.
The menu appears.
The menu...

Using the Menu19 
Using the Menu
The unit is equipped with an on-screen menu for making 
various adjustments and settings such as picture control, 
input setting, set setting change, etc.  You can also 
change the menu language displayed in the on-screen 
menu.
To change the menu language, see “Selecting the Menu 
Language” on page 18.
The current settings are displayed in place of the x 
marks on the illustrations of the menu screen.
1Press the CONTROL button.
The operation buttons are displayed.
2Press...

Adjustment Using the Menus 20
About the memory of the settings
The settings are automatically stored in the monitor 
memory.Adjustment Using the 
Menus
Items
The screen menu of this monitor consists of the 
following items.
STATUS (the items indicate the 
current settings.)
For the video input
FORMAT
COLOR TEMP
COMPONENT LEVEL
NTSC SETUP
SCAN MODE
POWER SAVING
Model name and serial number
OPTION A and serial number
OPTION B and serial number
For the DVI/HD15 input
FORMAT
fH
fV
COLOR TEMP
POWER SAVING...