Sony Klv S19a10e Operating Instructions

Introducing the TV
11
Introducing the TV
Installing the TV
Preventing the TV 
from Toppling OverAttaching the Support Belt
1Screw the support belt (supplied) to the TV stand with a wood screw 
(supplied).
2Attach the support belt to the stand, and screw the belt with a securing 
screw (supplied) using a coin, etc.
3Adjust the length by pulling the support belt towards you while holding 
the TV stand.
When Mounting on a Wall
Be sure to use the following optional wall-mount brackets to hang the TV on 
the...

Introducing the TV
12
Bundling the 
Connecting CablesYou can bundle the connecting cables as illustrated below.
1Bundle the connecting cables.
2Route the connecting cables through the hook.
Adjusting the 
Viewing Angle of the 
TVThis TV can be adjusted within the angles shown below.
Do not bundle the AC power cord for KLV-S23A10, KLV-S26A10 and 
KLV-S32A10 in the stand with other connecting cables.
KLV-S19A10 KLV-S23A10
KLV-S26A10KLV-S32A10
When adjusting the angle, hold the stand with one hand 
to avoid...

Introducing the TV
13
Introducing the TV
TV Controls and Connectors
Front and Top Panel
78 9 0
qa
PIC OFFTIMERPOWER
ENTERWEGA GATE
TV/VIDEOVOLUMECHANNEL POWER
1236 45
ItemDescription
1ENTERPress to confirm the selection or setting.
2WEGA GATEPress to display WEGA GATE. Press again to exit WEGA GATE.
3TV/VIDEOPress repeatedly to cycle through the video equipment connected to the TV’s video inputs.
4
– VOLUME +Press to adjust the volume. In the WEGA GATE screen, these buttons serve as left/right 
buttons....

Introducing the TV
14
Side Panel
IN
AUDIO  IN
L
R5
4PC  IN
(RGB  IN)
5
6
VIDEO 2
IN
S  VIDEO
VIDEO
L
(MONO)
R
1
2
3
AUDIO
Left side Right side
ItemDescription
1VIDEO 2 IN 
S VIDEOConnects to the S VIDEO output jack on your camcorder or other video equipment that has 
S VIDEO. Provides better picture quality than composite video (2).
2VIDEO 2 IN 
VIDEO/
AUDIO L 
(MONO)/
AUDIO RConnect to the composite video and audio output jacks on your camcorder or other video 
equipment.
3Headphones 
jackConnects to...

Introducing the TV
15
Introducing the TV
Rear Panel
Y
P
B
PR
L
RAUDIOL
R
HD/DVD  IN
(1080i/720p/480p/480i)
4AUDIO
OUT
PC
AUDIO
IN
DC INVHF/UHF
S  VIDEO
VIDEO
AUDIO
(MONO)L
R
VIDEO  IN 13
AC IN
AC IN
AC INVHF/UHF
12
3 7
8 5 4
613
3 11
VHF/UHFVHF/UHF
KLV-S23A10
KLV-S19A10
KLV-S26A10KLV-S32A10
(Continued)
 

Introducing the TV
16
Jack Description
1VHF/UHFRF input that connects to your VHF/UHF antenna.
2DC IN 
(KLV-S19A10)Connects the supplied AC power adaptor.
3AC IN 
(KLV-S23A10/
KLV-S26A10/
KLV-S32A10)Connects the supplied AC power cord.
4VIDEO IN 1/3 
S VIDEOConnects to the S VIDEO output jack of your VCR or other video equipment that has 
S VIDEO. S VIDEO provides better picture quality than the composite video (5).
5VIDEO IN 1/3 
VIDEO/
L-AUDIO-RConnect to the composite video and audio output jacks on...

17
Connecting the TV
Connecting the TV
To display clear crisp pictures, first you must connect your TV correctly and 
also need to choose the correct display format (see “Changing the wide 
screen mode” on page 38). It is strongly recommended to connect the 
antenna using the supplied 75-ohm coaxial cable to receive optimum picture 
quality signal. A 300-ohm twin lead cable can be easily affected by radio 
noise and the like, resulting in signal deterioration. If you use a 300-ohm 
twin lead cable, keep...

Connecting the TV
18
Basic Connections
Cable System or 
VHF/UHF Antenna 
SystemCable or VHF only or VHF/UHF
From the Channel settings, select Cable On or Cable Off for your type of 
input signal.
Cable Box/Digital 
Cable BoxUse this hookup if:
sYou subscribe to a cable TV system that uses scrambled or encoded 
signals requiring a cable box to view all channels, and
sYou do not intend to hook up any other audio or video equipment to 
your TV.
1Connect the coaxial connector from your cable service to the...

Connecting the TV
19
Connecting the TV
Satellite Receiver 
and Cable/AntennaThis scenario shows a SAT Box connected through the video inputs and the 
Cable/Antenna connected through the VHF/UHF input. Satellite signals are 
selected by the SAT Box through the video inputs while TV signal is 
selected by the TV tuner.
To connect a satellite receiver
1Connect the satellite antenna cable to the satellite receiver’s satellite 
input jack.
2Use an A/V and S VIDEO cables to connect the satellite receiver’s...

Connecting the TV
20
HD EquipmentDisconnect all power sources before making any connections.
1Using a component video cable, connect your equipment’s YPBPR 
output jacks to the TV’s YP
BPR input jacks. Use the HD/DVD IN 4 
connections.
2Using an audio cable, connect your equipment’s AUDIO output jacks to 
the TV’s AUDIO input jacks.
Component video (YPBPR) connection is necessary to view 480p, 
720p, and 1080i formats. Note that this TV displays all format types 
of picture in a resolution of 1,280 dots...