Sony Ke P42xs1 Operating Instructions

11
GB
The buttons labelled 5, qd and qk are also used for Teletext operation. For details see page 36.
. 
qaa) Displaying a channel or an input signal index: If Media Selector 
(3) is switched to TV and MENU is switched off, press OK to display a 
channel or input signal index. Once you have pressed OK:
1 To select a channel: press v or V to select a channel and next press 
again the OK button to watch the selected channel.
2 To select an input signal: while watching the channel index, press b to...

12
Overview of the TV Buttons and side Connectors 
On/Off switch
Volume control buttons (+/-)Programme Up or Down buttons 
(selects TV channels)
TV mode button Selecting Input Source button 
(see page 40)
(MONO)
L/G/S/I
R/D/D/D
Overview of the TV Buttons
Overview of the side Connectors
Headphones 
jack
Video Input 
jack S Video Input 
jack
Audio Input 
jacks
Auto Start Up button (starts 
the auto start up sequence, see 
page 15)
Overview & Installation
 

13
GB
Overview & Installation
Overview of the TV indicators
Inserting Batteries into the Remote Control
Make sure you insert the supplied batteries using the correct polarities.
Always remember to dispose of used batteries in an environmental friendly way.
To operate 
the remote 
control, point 
it towards 
this receiver.
Lights up in blue when you 
press  (picture off) on 
the remote control to 
switch off the picture. Only 
the picture is switched off 
(the sound remains 
unchanged).
Lights up in red...

14
Connecting the Aerial and VCR
Stabilizing the TV set
After setting up, secure the TV set to a wall, pillar, etc, using the supplied anchor attachments, for safety 
purposes.
1 Remove the two screws attached to the upper rear side
of the TV set.
2 Replace the two screws with the two supplied anchor 
attachments.
3 Secure a wall anchor bracket (not supplied) to a solid wall or 
pillar.
4 Pass a strong cord or chain through both holes of the anchor
attachments and then secure to a wall or pillar, etc....

15
GB
1 Connect the TV plug to the mains socket (220-240V 
AC, 50Hz).
2The first time that the TV set is connected, it is usually 
turned on. If the TV is off, press the  on/off button on 
the TV set to turn on the TV.
The first time you switch on the TV, a Language 
menu appears automatically on the TV screen.
3Press the V, v, B or b buttons on the remote control to select your 
language, then press the OK button to confirm your selection. From 
now on all the menus will appear in your chosen language....

16
5A diagram appears showing you how to connect a wide range of 
equipment to your TV set. Follow the instructions and press the 
OK button to remove the picture and continue the automatic 
process. 
The connection diagram should be used as a guide only as 
most equipment can be connected to more than one type of 
TV socket. Once the TV has completed the automatic 
tuning process, refer to the ‘Connection Guide’ section on 
page 23 for further information on getting the best set up for 
your equipment....

17
GB
Introducing and Using the Menu System
Your TV set uses an On-Screen menu system to guide you through the operations. Use the following buttons 
on the Remote Control to operate the menu system: 
1To switch on the menu screens:
Press the MENU button to switch the first level menu on.Picture AdjustmentPicture Mode: Live
Contrast:
Reset:
Noise Reduction: Auto
Colour Tone: Cold
Select: Enter:OKExit:MENU
Picture AdjustmentPicture Mode: Live
Contrast:
Reset:
Noise Reduction: Auto
Colour Tone: Cold...

18
The Picture Adjustment Menu
The “Picture Adjustment”  menu allows you to 
alter the picture settings.
To do this:
Press the MENU button and then press OK to 
enter this menu. Next, press 
v or V to select the 
desired option and press OK. Finally, read below 
how to operate into each option.
Picture Mode  This option allows you to customise the Picture Mode based on the programme 
you are watching. After selecting this option press OK. Next, press repeatedly 
v 
or 
V to select:   
Live  (for live...

19
GB
ResetPress OK to reset the picture to the factory preset levels.
Noise This option is set to Auto to automatically reduce the snowy picture visible in the weak broadcast
Reduction  signal. However, it can be modified. After selecting this option press 
b. Next, press v or V to 
select High, Mid, Low or Off. Finally, press OK to store.
Colour ToneThis option allows you to alter the tint of the picture. After selecting this option press b. Next, press 
repeatedly 
v or V to select: Warm (gives the...

20
The Sound Adjustment Menu
The “Sound Adjustment” menu allows you to 
alter the sound settings.
To do this: 
Press the MENU button and press 
v to select 
, then press OK to enter this menu. Next, 
press 
v or V to select the desired option and 
press OK. Finally, read below how to operate 
into each option. 
SoundThis option allows you to customise the Sound Effect. After selecting this
Effectoption press OK. Next, press repeatedly 
v or V to select: 
Dolby*(Dolby Virtual, simulates the sound effect...