Sony Ht Ct500 Operating Instructions

11US
Getting StartedConnecting the speaker cord to the speaker
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker. 
Connect the speaker cords to match the color of the SPEAKER jacks.
Connect the connector for the remote control to the REMOTE CTRL jack.
 When you install the speaker or a TV on a wall, be careful not to stumble over the cord connected to the speaker.
Note
R REMOTE
CTRL
ONLY FOR SA-WCT500CENTER L
Rear of the speaker
White
Green
Red...

12US
To Customers
Sufficient expertise is required for installing this 
product. Be sure to subcontract the installation to 
Sony dealers or licensed contractors and pay 
special attention to safety during the installation. 
Sony is not liable for any damages or injury 
caused by mishandling or improper installation, 
or installing anything other than the specified 
product. Your statutory rights (if any) are not 
affected.
On Safety
Products by Sony are designed with safety in 
mind. If the products are...

13US
Getting Started
Do not lean or hang on the products.
 Do not lean or hang on the products, as they 
may fall on you and cause serious injury.
Pay attention to the location.
 Do not install the products on wall surfaces 
such as a pillar, where the corners or the sides 
of the products protrude away from the wall 
surface. If a person or object happens to hit the 
protruded corner or side of the products, it may 
cause injury or property damage.
 Do not expose the products to rain or moisture, 
or...

14US
CAUTION
If the following precautions are not observed, 
injury or property damage may occur.
Do not install any equipment other than the 
specified product.
 The WS-CT500EB accessories (supplied) are 
designed for use with the specified equipment 
only. If you install equipment other than that 
specified, it may fall or break, and cause injury.
 Do not modify the products.
 Do not place anything hot directly on the 
products. The heat may cause discoloration or 
deformation of the products.
Be sure...

15US
Getting StartedInstalling the speaker on the TV stand
You can install the speaker with the following TV models (not supplied):
 KDL-40/46XBR9
 KDL-40/46W51xx*
* In the actual model names, the “xx” indicates numbers and/or characters specific to each model.
Although the shape of the TV stand base differs depending on the TV model, you can install the speaker 
on the TV stand following this procedure.
1Remove the screws of the TV.
2Detach the TV from the TV stand.
 Make sure to place the TV on a soft...

16US
3Remove the screw of the cover.
4Detach the cover from the TV stand.
When detaching the cover, slightly splay open the hooks of the cover from the front side of the 
stand with your fingers, and then push the cover toward the rear of the stand.
5Secure the extension bracket (supplied) to the TV stand with the large screws (+PSW5 
× 12 mm) (supplied).
Hooks
Extension bracket
 

17US
Getting Started
6Hook the rivets of the extension bracket to the holes of the back of the speaker and 
secure the speaker with the large screws (+PSW5 × 12 mm) (supplied).
7Reattach the TV.
Rear of the speaker
Holes
Rivet Front side
continued
 

18US
8Secure the TV with the screws removed in step 1.
9Attach the rear cover (supplied) with the small screws (M3 × 8 mm) (supplied).
 When carrying the SS-CT500 speaker-installed TV, do not hold it by the SS-CT500 speaker part. Doing so 
may cause damage or injury.
Note
Rear cover
 

19US
Getting Started
To prevent the TV from toppling over
As a protective measure, secure the TV.
1Place the TV on the center of the rack.
2Fit the support belt (supplied) to the TV, then firmly fasten with the screw for the support 
belt (+PSW4 × 20 mm) (supplied) using a screw driver.
3Fasten the support belt to the rack with the wood screw for the support belt (M3.8 × 20 
mm) (supplied).
 Be careful not to pinch your fingers when setting up the TV and rack.
Note
Screw for the support belt 
(+PSW4 × 20...

20US
To bundle the cords
You can bundle the cords using the clamper (supplied).
 Do not bundle the AC power cord (mains lead) using this clamper.
1Attach the clamper (supplied) on the rear cover.
2Bundle the cords, and then fasten the clamper.
Note
Clamper