Sony DPP FP70 User Manual

							71 GB
Additional information
On restrictions on duplication
If duplicating documents with the printer,
pay special attention to the following:
•Duplication of banknotes, coins, or
securities is against the law.
•Duplication of blank certificates,
licenses, passports, private securities, or
unused postal stamps is also against the
law.
•TV program, films, video tapes, others’
portraits or other materials may be
copyrighted.  Unauthorized video
printing of such materials may infringe
the provisions of the copyright law.
On color print packs
Notes on use
On Ink ribbon
•Do not touch the ink ribbon or place the
ink ribbon in a dusty location.
Fingerprints or dust on the ink ribbon
may result in imperfect printing.
•Do not rewind the ink ribbon and use
the rewound ink ribbon for printing.
Otherwise, proper printing result will
not be obtained, or even a malfunction
may occur.
If the ink ribbon does not click into
place, remove it and then re-insert it.
Only when the ink ribbon is too slack to
be loaded, wind the spool of the ink
ribbon in the direction of the arrow to
remove the slack.
•Never disassemble the ink ribbon.
•Do not pull out the ribbon from the ink
ribbon.
•Do not remove the ink ribbon while
printing.
On print paper
•The side without the imprinting is the
printing surface.  Inferior print quality
may result if the printing surface is
contaminated with dust or fingerprints.
Be careful to avoid touching the printing
surface.
•Do not bend the paper or tear it off at the
perforations before printing.
•To avoid paper jam or malfunctions of
the printer, make sure the following
before printing:
–Do not write or type on the print
paper.  Use the oil ink pen to write on
the paper after printing.  You cannot
type on the print paper using an ink-
jet printer, etc.
–Do not attach sticker or stamps on the
print paper.
–Do not fold or bend the print paper.
–Total number of print paper does not
exceed 20 sheets.
–Do not print on the used print paper.
Printing an image twice on the same
paper will not make the printed image
thicker.
–Use the print paper for this printer
only.
–Do not use the print paper ejected
without printed.
•Do not print on used sheets of print
paper or attempt to rewind the ribbon
inside the ink ribbon.  Doing so could
result in damages to the printer.
•Do not remove the paper tray while
printing.
Continued
Downloaded From ManualsPrinter.com Manuals 
						

							72 GB
About the Memory
Cards
About the “Memory Stick”
What is “Memory Stick”?
“Memory Stick” is a compact-size IC
recording medium with a large capacity. It
has been designed not only for exchanging/
sharing digital data among “Memory Stick”
complaint products, but also for serving as
an insertable/removable external storage
medium that can save data.
Types of “Memory Stick” that
the printer can use
With the printer, you can use the following
types of “Memory Stick”*3:
Notes on storing print packs
•When you are going to store a partially-
used pack of the ink ribbon and print
paper for an extended period of time,
store it in its original bag or in a similar
container.
•When you are going to store print paper
in the paper tray, make sure to close the
tray cover and slide cover.
•Avoid placing the ink ribbon in locations
subject to high temperature, high
humidity, excessive dust, or direct
sunlight. Please store it in a dark and
cold location and use it early. Depending
on the storage status, color elements of
the ink ribbon may deteriorate. Sony
shall assume no responsibilities for any
damage, loss or failed printed results
that may be caused by use of such ink
ribbon.
•Avoid leaving the printing surface of the
print paper in contact with a plastic
eraser or plastic desk mats that includes
vinyl chloride or plasticizer for an
extended period of time;  color changes
or deterioration of the printed image
may occur.
*1 Data reading/recording that requires
“MagicGate” copyright protection cannot be
performed.  “MagicGate” is the general name
of a copyright protection technology
developed by Sony using authentication and
encryption.
*2 The printer is equipped with a slot compatible
with both standard-size and Duo-size media.
Without a Memory Stick Duo adaptor, you
can use both standard-size “Memory Stick”
and compact-size “Memory Stick Duo”.Display-
ing/
Printing
Memory Stick
(Not compatible with
MagicGate)
Memory Stick
(MagicGate Compatible)
MagicGate
Memory Stick
Memory Stick PRO
*2
Memory Stick Micro
(M2*4) Memory Stick type
Delet-
ing/Sav-
ing/For-
matting
OK OK
OK
*1OK*1
OK*1OK*1
OK*1OK*1
OK*1OK*1
Downloaded From ManualsPrinter.com Manuals 
						

							73 GB
Additional information
LOCKLOCK
Write
protect
position Write
enable
position Connector
Place the label here.Write-protect switch *3 The printer supports FAT32. The printer has
been demonstrated as operable with a
“Memory Stick” with a capacity of 8GB or
smaller manufactured by Sony Corporation.
However, we do not guarantee the operations
of all the “Memory Stick” media.
*4 “M2” is an abbreviation for “Memory Stick
Micro”. In this section, “M2” is used to
describe “Memory Stick Micro”.
For the latest information on available
medium or others, access the following
home page:
http://www.memorystick.com/en/
support/support.html
Select the area where you use your printer,
and then select “Digital Printer” from each
area page.
Notes on use
•For the latest information on the “Memory
Stick” that the printer supports, see the
“Memory Stick” compatibilities information
on the Sony web site.
•Do not insert multiple “Memory Stick” at the
same time, which may cause trouble with the
printer.
•When using a “Memory Stick”, make sure to
check correct insertion direction. Wrong usage
may cause trouble with the printer.
•When using the “Memory Stick Micro” with
the printer, always insert it into an M2
adaptor.
•If you insert the “Memory Stick Micro” into
the printer without an M2 adaptor, you may
be unable to remove the “Memory Stick
Micro”.
•If you insert the “Memory Stick Micro” into
an M2 adaptor, and insert the M2 adaptor into
the Memory Stick Duo adaptor, the printer
may not operate properly.
•Do not place the “Memory Stick Duo”, an
“Memory Stick Duo”-sized M2 adaptor, or M2
media within the reach of a small child to
prevent him from swallowing it by accident.
•Avoid removing the “Memory Stick” from the
printer while the printer is reading or writing
data.•Data may be damaged in such occasions:
–“Memory Stick” is removed or the printer
is turned off during a read or write
operation.
–“Memory Stick” is used in a location
subject to static electricity or electrical
noises.
•We recommend that you save backup of the
important data.
•The data processed with the computer may
not be played with the printer.
•When you format a “Memory Stick”, use the
format function of the printer or your digital
camera. If you format a “Memory Stick” with
your computer, images may not be displayed
properly.
•When you format a “Memory Stick”, all the
data including the protected image files will
be erased. To avoid erasing important data by
accident, make sure to check the content
before formatting.
•You cannot record, edit or delete data if you
slide the write-protect switch to LOCK.
•When you use a “Memory Stick Duo” without
the write-protect switch, be careful not to edit
or delete the data by accident.
•When you slide the write-protect switch of the
“Memory Stick Duo”, use a thin-pointed
device.
•Do not attach any other material than the
supplied label on the labeling position. When
you attach the supplied label, be sure to attach
it to the labeling position. Be careful that the
label does not stick out.
•When you write on the memo area of the
attached label, do not write forcefully.
•When you carry or store the “Memory Stick”,
put it in the case designed for the “Memory
Stick”.
Continued
Downloaded From ManualsPrinter.com Manuals 
						

							74 GB
•Do not touch the terminal of the “Memory
Stick” with your hand or a metal object.
•Do not strike, bend or drop the “Memory
Stick”.
•Do not disassemble or modify the “Memory
Stick”.
•Do not expose the “Memory Stick” to water.
•Do not use or store the “Memory Stick” under
the following conditions:
–Locations beyond the required operational
conditions including locations such as the
hot interior of a car parked in the sun or/
and in the summer, the outdoors exposed
to direct sunlight, or a place near a heater.
–Humid locations or locations with corrosive
substances present
About the SD card
The SD card slot of the printer allows you
to use the following:
•SD memory card
*1
•miniSD card
•SDHC memory card*2
•MMC standard memory card*3
We do not guarantee proper operations for
all types of SD memory cards and MMC
standard memory cards.
*1 The printer has been demonstrated as
operable with an SD card with a capacity of 2
GB or smaller.
*2 The printer has been demonstrated as
operable with an SDHC card with a capacity
of 4 GB or smaller.
*3 The printer has been demonstrated as
operable with an MMC standard memory
card with a capacity of 2 GB or smaller .
Notes on use
•When using a card, make sure to check correct
insertion direction of the card and correct
insertion slot.
•You cannot read or write the data subject to
the copyright protection.
•Do not strike, drop, or bend a card.
•Do not disassemble or modify a card.
•Do not expose a card to water.•Avoid using a card in areas subject to high
humidity, since it may be easily affected by
the humidity.
•Do not use or store a card in a location subject
to:
–extremely high temperature such as the hot
inside of a car or the outdoors exposed to a
direct sunlight, or a place near a heater.
–direct sunlight
–high humidity or corrosive substances
–static electricity or electrical noises
•When you carry or store a card, put it in the
case supplied with it.
•Do not remove a card or turn off the printer
while the printer is reading or writing data
and the access indicator is flashing.
Otherwise, data may be rendered unreadable
or erased.
About the CompactFlash card
The CompactFlash card slot of the printer
allows you to use the following:
•CompactFlash Storage Card (Type I/
Type II) and CF+Card (Type I/Type II)-
compatible CompactFlash Storage
Card
*4.
•Micro Drive
•COMPACT VAULT
You can also use the following by using a
commercially available CompactFlash card
adaptor
*5:
•Smart Media card*5
•xD-Picture Card*5
However, we do not guarantee proper
operations for all types of CompactFlash
cards.
*4 Use a CompactFlash card with a power
specification of 3.3V or 3.3V/5V. You cannot
use a type for 3V or 5V only. Do not insert
other types of CompactFlash card into the
printer’s insertion slot.  The printer may be
damaged.
*5 When using a commercially available
CompactFlash card adaptor, refer to the
operating instructions of the adaptor you use
for how to install the card and adaptor.
Downloaded From ManualsPrinter.com Manuals 
						

							75 GB
Additional information
Specifications
x Printer
Printing method
Dye sublimation printing  (Yellow/
Magenta/Cyan 3 pass)
Resolution
300 (H) x 300 (V) dpi
Image processing per dot
256 levels processing (8 bits for each
Yellow/Magenta/Cyan)
Printing size
P (Post Card/4 x 6 inch) size:
101.6 x 152.4 mm (maximum,
borderless)
Printing time (per sheet)
Memory card
*1*2*3*4:
Approx. 45 sec.
PictBridge
*3*5:Approx. 56 sec.
Via PC*6:Approx. 50 sec.
Input/Output connectors
USB (Full Speed) for PC connection
PictBridge/EXT INTERFACE
connector
Slot
“Memory Stick” insertion slot
SD Card insertion slot
CompactFlash card insertion slot
Compatible image file formats
JPEG: DCF 2.0 compatible, Exif
  2.21
compatible, JFIF*7
TIFF: Exif 2.21 compatible
BMP*8:1, 4, 8, 16, 24, 32 bits Windows
format
Some image file formats are not
compatible.
Continued
When using the CompactFlash card adaptor,
the write-protected card may not work
properly.
Notes on use
•When using a card, make sure to check correct
insertion direction of the card and correct
insertion slot.
•Do not strike, drop, or bend a card.
•Do not disassemble or modify a card.
•Do not expose a card to water.
•Avoid using a card in areas subject to high
humidity, since it may be easily affected by
the humidity.
•Do not use or store a card in a location subject
to:
–extremely high temperature such as the hot
inside of a car or the outdoors exposed to a
direct sunlight, or a place near a heater.
–direct sunlight
–high humidity or corrosive substances
–static electricity or electrical noises
•When you carry or store a card, put it in the
case supplied with it.
•Do not remove a card or turn off the printer
while the printer is reading or writing data
and the access indicator is flashing.
Otherwise, data may be rendered unreadable
or erased.
Downloaded From ManualsPrinter.com Manuals 
						

							76 GB
Maximum number of pixels to be
handled
8 000(H) x 6 000(V) dots
(Excluding Index Print and part of
Creative Print)
Maximum number of files to be handled
9 999 files for a memory card/an
external device
Ink ribbon/Print Paper
See supplied “Read This First”.
LCD screen
LCD panel:
DPP-FP70:  6.2 cm (2.5 type) TFT
drive
DPP-FP90:  9.0 cm (3.6 type) TFT
drive
Total number of dots:
DPP-FP70: 115 200 (480 x 240)
DPP-FP90: 230 400 (320 RGB x 240)
Power requirements
DC IN jack, DC 24V
Power consumption
While printing: 80 W (maximum)
On standby mode: less than 1W
Operating temperature
5 ˚C to 35 ˚C (41 ˚F to 95 ˚F)
Dimensions
[DPP-FP70]
Height: Approx. 63 mm
( 2 
1/2 inches) (printer)
Approx. 72 mm
( 2 
7/8  inches) (including
LCD projecting parts)
Width: Approx. 180 mm
( 7 
1/8 inches)
Depth: Approx. 137 mm
( 5 
1/2 inches) (excluding
a handle)
Approx. 149 mm
( 5 
7/8 inches)
(including a handle)[DPP-FP90]
Height: Approx. 66 mm
( 2 
5/8 inches)
Width: Approx. 180 mm
( 7 
1/8 inches)
Depth: Approx. 137 mm
( 5 
1/2 inches)
(excluding a handle)
Approx. 149 mm
( 5 
7/8 inches)
(including a handle)
Depth when the paper tray is
installed: Approx. 169 mm  ( 6 
3/4inches) longer than the above depth.
Mass
DPP-FP70: Approx.  1.1 kg (2 lb 7 oz)
DPP-FP90: Approx.  1.2 kg (2 lb 10 oz)
(excluding the paper tray, ink ribbon,
AC power adaptor)
Supplied accessories
See supplied “Read This First”.
x AC power adaptor AC-S2422
Power requirements
AC 100V to 240 V, 50/60 Hz,
1.5A to 0.75 A
Rated output voltage
DC 24 V, 2.2 A (Peak 3.7 A, 6.5 s)
Operating temperature
5 ˚C to 35 ˚C (41 ˚F to 95 ˚F)
Dimensions
Approx. 60 x 30.5 x 122 mm
(2 
3/8  x 1 1/4 x 4 7/8 inches)
(w/h/d, excluding protruding parts
and cables)
Mass
Approx.  305 g (11 oz)
Design and specifications are subject to
change without notice.
Downloaded From ManualsPrinter.com Manuals 
						

							77 GB
Additional information
Printing range
P size152.4 mm/6 inch
(1 800 dots)
95.5 mm/
3 
7/8 inch
 (1 128 dots)101.6 mm/
4 inch
(1 200 dots)
The above illustrations are those when an image with a 2:3 aspect ratio is printed.
The printing range differs for a border or a borderless print.
Border print range
Borderless print
range
Perforations 146.3 mm/5 
7/8 inch
(1 728 dots) *The total number of sheets of P size print paper
that the printer can print is estimated to be
approximately 2,000. For the total number of
sheets, please check “Printer Information
Display” of the “Display/Printer setup” menu
(page 34).
*1: Print Settings: Borderless, No time stamp,
AutoFine Print 4: ON (Photo)
*2: When printing a photo (4.22 MB file size)
taken by a Sony digital still camera
containing effective picture elements of
approximately 10,100,000 or equivalent.
*3: Print Speed: Time from when the PRINT
button is pressed to when printing is
finished. (The printing time may vary
depending on a used equipment, a format
of an image, a used memory card, settings
of an application and operating conditions.)*4: When printing from a “Memory Stick PRO
Duo” inserted in the printer ’s slot
*5: When printing via DSC-N2 connected by
USB cable. Time from when the “PRINT”
button on the OSD of the camera is pressed
to when the printing is finished.
*6:
The time for data processing and
transferring is excluded.
*7: Baseline JPEG with 4:4:4, 4:2:2, or 4:2:0
format
*8: You cannot print using the Picture Motion
Browser.
Customer support home page
The latest support information is available at
the following home page address:
http://www.sony.net/
Downloaded From ManualsPrinter.com Manuals 
						

							78 GB
Glossary
DCF (Design rule for Camera File system)
This camera conforms with the DCF
(Design rule for Camera File system)
standard established by JEITA (Japan
Electronics and Information Technology
Industries Association) to maintain file
exchangeability and compatibility
between digital cameras and related
products. Complete exchangeability and
compatibility, however, are not
guaranteed.
DPOF (Digital Print Order Format)
The format used to record the
information necessary for automatically
printing images shot by a digital camera
at a printing shop or with a home-use
printer. The printer supports DPOF
printing and can automatically print the
preset number of copies of the DPOF
preset images.
Exif 2.21 (Exif Print)
Exif (Exchangeable image file format for
digital cameras) Print is a global
standard for digital photo printing.  A
digital camera supporting Exif Print
stores the data relevant to the conditions
of shooting as each shot is taken.  The
printer utilises the Exif Print data stored
in each image file to ensure the printed
result matches the original shot as
closely as possible
*1.
 *1 When the “Auto Fine Print 4” is enabled
and an image (JPEG file) is shot by an Exif
Print (Exif 2.21)-compliant digital camera,
the image is automatically adjusted to its
optimum picture quality and printed.
“Memory Stick”/CompactFlash card/SD
card
Compact, light, removable storage
media.  For details see pages 72 to 75.
PictBridge
A standard specified by Camera &
Imaging Products Association that
allows you to connect PictBridge-
complaint digital camera directly to the
printer without a PC, enabling direct
printing on the spot.
Thumbnails
Miniature images for representing the
original images that are stored in the
image files taken by a digital camera.
The printer uses thumbnails in the image
list.
Downloaded From ManualsPrinter.com Manuals 
						

							79 GB
Additional information
Superimpose characters glossary
You can use the characters here to superimpose onto an image. Please take a picture of the
desired characters in advance, and follow the procedures for superimposing handwriting
in pages 23 and 24 to trim the necessary portion and superimpose it onto an image.
Downloaded From ManualsPrinter.com Manuals 
						

							80 GB
Downloaded From ManualsPrinter.com Manuals