Sony Dav Is10 Operating Instructions

							Getting Started – ADVANCED –
masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
21GB
Connecting the TV with the video cord/component video cord/
HDMI cableSends the played back DVD image to the connected TV.
Check the jacks of your TV, and choose connection method A, B, or C. Picture quality improves in 
order from A (standard) to C (HDMI).Note When connecting the HDMI cable, make sure that the direction of jacks are the same..Getting Started – ADVANCED –Connecting the TV (Advanced)
YPB/CBPR/CR
VIDEO
IN
IN
DMPORT
TV with COMPONENT 
VIDEO IN jacks TV with HDMI IN jack
A
B C
To the component 
video input jacks To the video 
input jack
TV with VIDEO IN jackRear of the 
control unit
: Signal flow To HDMI OUT jack
To VIDEO OUT 
(VIDEO) jackTo VIDEO OUT 
(COMPONENT) jacksTo the HDMI input 
jack
cont
inue
d
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
22GB
A
To connect to a TV with the VIDEO IN jack
Connect the video cord..B
To connect to a TV with the COMPONENT VIDEO IN jacks
Connect a component video cord (not supplied). To use the VIDEO OUT (COMPONENT) jacks (Y, 
PB/CB, PR/CR) instead of the video jacks, your TV monitor must be equipped with COMPONENT 
VIDEO IN jacks (Y, P
B/CB, PR/CR). If your TV accepts progressive format signals, you can use this 
connection and set the output channel of the system to progressive format (this system is compatible 
with the 525 or 625 progressive format) (page 91).
C
To connect to a TV with the HDMI (high-definition multimedia 
interface)/DVI (digital visual interface) IN jack
Use a certified HDMI (high-definition multimedia interface) cable (not supplied) to enjoy high quality 
digital picture and sound through the HDMI OUT (high-definition multimedia interface out) jack.HDMI (high-definition multimedia interface)
The system incorporates High-Definition Multimedia Interface (HDMI
TM) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI 
Licensing LLC.
To connect to a TV with DVI (digital visual interface) input Use an HDMI (high-definition multimedia interface)-DVI (digital visual interface) converter cord (not 
supplied) with an HDMI (high-definition multimedia interface)-DVI (digital visual interface) adaptor 
(not supplied). The DVI (digital visual interface) jack will not accept any audio signals. Furthermore, 
you cannot connect the HDMI OUT (high-definition multimedia interface out) jack to DVI (digital 
visual interface) jacks that are not HDCP (high-bandwidth digital content protection) compliant (e.g., 
DVI (digital visual interface) jacks on PC displays).
YellowRed
Blue
Green
 
						

							Getting Started – ADVANCED –
masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
23GB
Connecting the TV with the digital optical cordA TV with a digital optical out jack (TV with built-in digital satellite receiver, etc.) can be connected 
to the TV (DIGITAL IN OPTICAL) jack instead of the TV (AUDIO IN) jacks on the rear of the control 
unit.
The system can accept both the digital and analog signals. Digital signals have priority over analog 
signals. If the digital signal ceases, the analog signal will be processed after a few seconds.Note When connecting the digital optical cord, insert the connector until it clicks.
OPTICAL 
DIGITAL
OUT
DMPORT
TV with the digital optical jackRear of the control unit
To the digital 
optical output jack
To TV (DIGITAL 
IN OPTICAL) jack
: Audio signal flow
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
24GB
 You can enjoy other components.Connecting the system and the other componentOutputs the other component through the speakers of this system.Note Do not connect or disconnect the DIGITAL MEDIA PORT adapter to/from the control unit while the system is 
turned on.
 When connecting the DIGITAL MEDIA PORT adapter, be sure to match the V marks..Tip You can assign a digital sound input corresponding with the function “TV” and “SAT/CABLE.” For details, see 
[DIGITAL IN] (page 93).Connecting Other Components
COAXIAL 
DIGITAL
OUT
DMPORT
DIGITAL MEDIA 
PORT adapterTo SAT/CABLE 
(DIGITAL IN COAXIAL) jack
: Signal flow Rear of the
control unit
To DMPORT jack To the digital  
coaxial output jackVCR, digital satellite 
receiver, etc.
 
						

							Getting Started – ADVANCED –
masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
25GB
To connect the DIGITAL MEDIA PORT adapterConnect a DIGITAL MEDIA PORT adapter (not supplied) to the DMPORT jack. For details of the 
DIGITAL MEDIA PORT adapter, see “Using the DIGITAL MEDIA PORT Adapter” (page 80).If you connect a digital satellite receiver with a DIGITAL OUT (COAXIAL 
or OPTICAL) jackA digital satellite receiver can be connected to the SAT/CABLE (DIGITAL IN COAXIAL) or TV 
(DIGITAL IN OPTICAL) jack.
To connect, use a digital coaxial cord (not supplied) for the SAT/CABLE (DIGITAL IN COAXIAL) 
jack or digital optical cord (not supplied) for the TV (DIGITAL IN OPTICAL) jack.
The system can accept both digital and analog signals. Digital signals have priority over analog signals. 
If the digital signal ceases, the analog signal will be processed after a few seconds.Note Be sure to make connections securely to avoid hum and noise.
Digital coaxial cordDigital optical cord
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
26GB
 You can use the speakers installed on a wall.Installing the speakers on a wall1
Prepare screws (not supplied) that are suitable for the holes of the bracket.
2
Secure the bracket to the wall using hole 1.Tip To prevent the speaker from rotating, use the hole 2, too.
3
Remove the rear cap using the wrench (supplied), and remove the speaker pedestal 
using a screwdriver (+) (not supplied).Installing the Speakers on a Wall
1
34
2Rear cap Wrench (supplied)
 
						

							Getting Started – ADVANCED –
masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
27GB
4
Push A with the supplied wrench (1), and then remove the speaker cords (2).
5
Thread the speaker cords through hole 3.
6
Reconnect the detached speaker cords, matching 3/# to the appropriate speaker 
terminals (1), and then push the lever down completely (2).
Tip If it is difficult to push the lever down, use the wrench (supplied).
(1)
When the lever is down, the 
speaker cords are locked.When the lever is up, the 
speaker cords can be removed. (2)
A
3
#3 (1)(2)
cont
inue
d
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
28GB
7
Reattach the rear cap using the wrench (supplied).
8
Secure the speaker to the bracket with the screw in Step 3 using hole 4.
Note Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where 
reinforcement is applied.
 Contact a screw shop or installer regarding the wall material or screws to be used.
 Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or 
improper screw installation, natural calamity, etc.About connecting speaker cordThe connectors of the speaker cords are the same color as the jacks to be connected.
4
#3
BlackDo not catch the 
speaker cords 
insulation in the speaker 
terminals.
 
						

							Getting Started – ADVANCED –
masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb05gsa.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
29GB
Tip You can remove the speaker cords from the connector. With the catch facing down, press and hold the connector 
down against a flat surface (1) and remove the speaker cords from the connector (2).To avoid short-circuiting the speakersShort-circuiting of the speakers may damage the system. To prevent this, be sure to follow these 
precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch 
another speaker terminal or the bare wire of another speaker cord, such as shown below.Note Be sure to match the speaker cords to the appropriate speaker terminals: 3 to +, and # to –. If the cords are 
reversed, the sound will lack bass and may be distorted.
Catch(1)
(2)Stripped speaker cord is 
touching another speaker 
terminal.Stripped cords are touching each 
other due to excessive removal of 
insulation.
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb06bas.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
30
GB
Basic Operations
Depending on the DVD or VIDEO CD, some operations may be different or restricted.
Refer to the operation details supplied with your disc.Basic OperationsPlaying Discs
     
FUNCTION
VOLUME
"/1Z"/1
H Disc slotFUNCTION
VOLUME +/– x
MUTING ./>
X/
Z Soft-touch buttons
Note Soft-touch buttons function by touching lightly. Do not press 
them strongly.
 Do not place objects on the top of the control unit. Doing so 
may activate the soft-touch buttons or deactivate the buttons 
of the control unit.Tip Soft-touch buttons function when they are lit up.
 You can select the way of displaying the soft-touch buttons 
located on the top of the control unit (page 79).