Sony Dav Is10 Operating Instructions

							masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
11GB
Getting Started – BASIC –
Note on handling the subwoofer Do not place your hand into the slit of the subwoofer 
when lifting it. The speaker driver may be damaged. 
When lifting, hold the bottom of the subwoofer.
 Do not push the top of the subwoofer where the 
speaker unit is installed.
Slits Subwoofer
Speaker unit
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
12
GB
Getting Started – BASIC –
The following is the basic connection of the system.
Refer to the connection diagram below, and read the additional information from 1 to 4 on the 
following pages.Step 2: Connecting the System
DMPORT
CENTER SUR L SUR R FRONT L FRONT R
SYSTEM CONTROL  
ONLY FOR HCD-IS10
SPEAKER    
ONLY FOR SS-IS10
3 AM loop antenna (aerial)
Subwoofer4 AC power cord 
(mains lead) 3 FM wire 
antenna 
(aerial) 2 Front 
speaker (L)2 Center speaker
2 Surround 
speaker (R) 2 Surround 
speaker (L)2 Front 
speaker (R)
1 Plug Bottom of the 
subwooferRear of the control unit
 
						

							masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
13GB
Getting Started – BASIC –
1 Connecting the Control unitConnect the system connector of the control unit to the SYSTEM CONTROL jack of the subwoofer.
Insert the plug of the SYSTEM CONTROL cord, then secure the screws of the plug.
DMPORT
SYSTEM CONTROL  
ONLY FOR HCD-IS10
SPEAKER    
ONLY FOR SS-IS10
CENTER SUR L SUR R FRONT L FRONT R
Subwoofer
SYSTEM CONTROL cordRear of the control unit Bottom of the subwoofer
ScrewsPlug
cont
inue
d
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
14
GB
Getting Started – BASIC –
2 Connecting the SpeakersConnect the connectors of the speaker cords to their corresponding SPEAKER jacks. The connectors 
of the speaker cords are the same color as the jacks to be connected.3 Connecting the Antenna (Aerial)To connect the AM loop antenna (aerial)The shape and the length of the antenna (aerial) is designed to receive AM signals. Do not dismantle 
or roll up the antenna (aerial).1
Remove only the loop part from the plastic stand.
2
Set up the AM loop antenna (aerial).
SYSTEM CONTROL  
ONLY FOR HCD-IS10
SPEAKER    
ONLY FOR SS-IS10
CENTER SUR L SUR R FRONT L FRONT R
SubwooferSpeaker cords
Bottom of the 
subwoofer Center speaker Front speaker (R) Front speaker (L)
Speaker cords
Surround speaker (L) Surround speaker (R) RedGreen
White
Gray
Blue
 
						

							masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
15GB
Getting Started – BASIC –
3
Connect the cords to the AM antenna (aerial) terminals.The cords can be connected to either terminal.Note Do not place the AM loop antenna (aerial) near the system or other AV equipment, as noise may result.Tip Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
4
Make sure the AM loop antenna (aerial) is connected firmly by pulling softly.
To connect the FM wire antenna (aerial)Connect the FM wire antenna (aerial) to the FM 75 Ω COAXIAL jack.Note Be sure to fully extend the FM wire antenna (aerial).
 After connecting the FM wire antenna (aerial), keep it as horizontal as possible.Tip If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the control unit to an outdoor 
FM antenna (aerial) as shown below.
DMPORT
Insert until this 
part. Insert the cords pushing down the terminal clamp.
DMPORT
FM wire antenna (aerial)
(supplied)
FM 75 Ω COAXIAL jack
Outdoor FM antenna (aerial) Rear of the control unit
cont
inue
d
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
16
GB
Getting Started – BASIC –
4 Connecting the AC power cord (mains lead)Before connecting the AC power cord (mains lead) of the subwoofer to a wall outlet (mains), connect 
all the speakers to the subwoofer (page 14).Note After connecting the AC power cord (mains lead), wait about 20 seconds before turning on the power by pressing 
"/1.
Subwoofer
AC power cord 
(mains lead)To a wall outlet 
(mains)
 
						

							masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
17GB
Getting Started – BASIC –
The following is the basic connection of the control unit and TV. For other TV connections, see 
page 21. For other component connections, see page 24. Required cordsA
 Video cord
.This connection sends the image to the TV. Connect the VIDEO OUT (VIDEO) jack of the control unit 
to the VIDEO IN jack of the TV.B
 Audio cord (not supplied)
This connection sends TV sound to the system. You can enjoy TV sound from the speakers with this 
connection. Connect the TV (AUDIO IN) jacks of the control unit to the AUDIO OUT jacks of the TV.Note When connecting the jack, insert the plug into the jack as far as it will go.Step 3: Connecting the TV
R AUDIO
OUTLVIDEO
IN
DMPORT
TV
A B
Rear of the control unit : Video signal flow
: Audio signal flow
YellowWhite (L/audio)
Red (R/audio)
Example
Correct Incorrect
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
18
GB
Getting Started – BASIC –
Follow the steps below to make the minimum 
number of basic adjustments for using the 
system.1
Turn on the TV.
2
Press [/1.The system turns on.
3
Switch the input selector on your TV so 
that the signal from the system 
appears on the TV screen.[Press [ENTER] to run QUICK SETUP.] 
appears at the bottom of the TV screen. If 
this message does not appear, recall the 
Quick Setup display (page 20) and perform 
again.
4
Press   without inserting a disc.The Setup Display for selecting the 
language used in the on-screen display 
appears on the TV screen.
5
Press X/x to select a language.The system displays the menu and subtitles 
in the selected language.
6
Press .The Setup Display for selecting the aspect 
ratio of the TV to be connected appears.
7
Press X/x to select the setting that 
matches your TV type.
xIf you have a wide-screen TV or a 4:3 
standard TV with a wide-screen mode[16:9] (page 90)xIf you have a 4:3 standard TV[4:3 LETTER BOX] or [4:3 PAN SCAN] 
(page 90)
8
Press .The [AUTO CALIBRATION] display 
appears.
Step 4: Performing the 
Quick Setup
"/1
C/X/x/c,  
DISPLAY
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISHITALIANOFRAN
ÇAIS
ENGLISHDEUTSCHESPA
ÑOL
NEDERLANDS
DANSK
SVENSKA
SCREEN SETUP
TV TYPE:16:9
4:3 PAN SCAN 4:3 LETTER BOX
FULLYCBCR/RGB (HDMI):
BACKGROUND: SCREEN SAVER:
4:3 OUTPUT:
16:9
Connect calibration mic. Start
measurement?
YES
AUTO CALIBRATION
NO
 
						

							masterpage:Right
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
19GB
Getting Started – BASIC –
9
Connect the calibration mic to the 
ECM-AC2 jack on the rear of the control 
unit, and set it up at the ear level using 
a tripod, etc. (not supplied).The front of each speaker should face the 
calibration mic, and there should be no 
obstruction between the speakers and the 
calibration mic. Note The ECM-AC2 jack is used for the supplied 
calibration mic only. Do not connect other 
microphones.
10
Press X/x to select [YES], then press 
.[AUTO CALIBRATION] starts. Be quiet 
during the measurement.Note Loud test sound is output when [AUTO 
CALIBRATION] starts. You cannot turn the volume down. Give consideration to children 
and neighbor.
 Avoid being in the measurement area and 
making noise during the measurement (which 
takes about 1 minute), as it may interfere with 
measurement.
11
Unplug the calibration mic and press C/
c to select [YES].Note The environment of the room in which the 
system is installed may affect measurements.
 If measurement fails, follow the message then 
retry [AUTO CALIBRATION].
12
Press .Quick Setup is finished. All connections 
and setup operations are complete.
To quit the Quick SetupPress   DISPLAY in any Step.Tip If you cancel [AUTO CALIBRATION], perform the 
speaker settings in “Settings for the Speakers” 
(page 94).
 If you change the position of the speakers, reset the 
speaker settings. See “Calibrating the Appropriate 
Settings Automatically” (page 85).
 If you want to change any of the settings, see “Using 
the Setup Display” (page 88).
 For details on [AUTO CALIBRATION] and the error 
messages of [AUTO CALIBRATION], see 
“Calibrating the Appropriate Settings Automatically” 
(page 85).
DMPORT
Calibration mic Rear of the control unit
To  E C M - A C 2  j a c k
FRONT L :
FRONT R :
CENTER  :
SUBWOOFER :
SURROUND L :
SURROUND R :
If OK, unplug calibration mic and select
“YES”.
YES
5.00m    
 0.0dB
5.00m     0.0dB
5.00m  + 1.0dB
5.00m  + 4.0dB
3.00m  - 2.0dB
3.00m  - 2.0dB Measurement complete.
NO
cont
inue
d
 
						

							masterpage:Left
specdef v20060111 filename[G:\FM\Sony\0524\DAVIS10\3212589311\3212589311DAVIS10\gb04gsb.fm]
 model name [DAV-IS10]
 [3-212-589-31(1)]
20
GB
Getting Started – BASIC –
To recall the Quick Setup display1Press   DISPLAY when the system is in 
stop mode.The Control Menu display appears on the TV 
screen.2Press X/x to select   [SETUP], then 
press .The options for [SETUP] appear.3Press X/x to select [QUICK], then press  .The Quick Setup display appears.
1 2 ( 
2 7 )QUICK
QUICKRESET
DVD VIDEO
BNR
1 8 ( 
3 4 )CUSTOMT      
 0 : 0 0 : 0 2