Sony Dav Dz700fw Operating Instructions

Getting Started
21GB
 Do not set the speakers in an inclined position.
 Do not place the speakers in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight
 Use caution when placing the speakers and/or speaker stands (not supplied) that are attached with the speakers on 
a specially treated (waxed, oiled, polished, etc.) floor, as staining or discoloration may result.
 When cleaning, use a soft cloth such as a cleaning cloth for...

22GB
Examples of poor conditions of the speaker cord
After connecting all the components, speakers, and AC power cord (mains lead), output a test tone to 
check that all the speakers are connected correctly. For details on outputting a test tone, see page 89.
If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a speaker 
other than the one currently displayed on the Setup Display, the speaker may be short-circuited. If this 
happens, check the speaker...

Getting Started
23GB
4Attach the wall-mount pads on the rear side of the speaker.
5Hang the speakers on the screws.
 Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where 
reinforcement is applied.
 Contact a screw shop or installer regarding the wall material or screws to be used.
 Sony is not responsible for accident or...

24GB
About the wireless system
This wireless system adopts the Digital Infrared Audio Transmission system (page 96). The following 
diagram indicates the infrared transmission area (the range that the infrared rays can reach).
 Do not install the IR receiver in a place exposed to direct sunlight or strong light such as an incandescent lamp. 
 Do not use the IR transmitter or IR receiver that is not supplied with the system.
Note
10
10
10
10
Infrared signal
IR transmitterInfrared signal
IR transmitter...

Getting Started
25GB
Connect the supplied AM/FM antennas (aerials) for listening to the radio.
 To prevent noise pickup, keep the AM loop antenna (aerial) away from the system and other components.
 Be sure to fully extend the FM wire antenna (aerial).
 After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
 When you connect the supplied AM loop antenna (aerial), cord (A) or cord (B) can be connected to either terminal.
 If you have poor FM reception, use a 75-ohms coaxial...

26GB
First, perform the video connection, and then audio connection.
With your TV’s audio output connected to this system, you can listen to TV sound through the system 
speakers.
Connecting the video cords
Sends a played back DVD image to a TV.
Connect the system to your TV using the SCART (EURO AV) cord (not supplied). 
Be sure to connect the SCA RT (EURO A V) cord to the EURO  AV T OUTPUT (TO TV) jack on the 
system.
When you connect using the SCART (EURO AV) cord, check that the TV conforms to S...

Getting Started
27GB
PR/CR). If your TV accepts progressive format signals, you must use this connection and set the output 
channel of the system to progressive format (page 27).
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your TV screen.
To change the aspect ratio, see page 85.
Does your TV accept progressive signals?
Progressive is the method for displaying TV images which reduces flickering, and sharpens the image. 
To display using this method, you need...

28GB
xP VIDEO (PROGRESSIVE VIDEO)
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT VIDEO OUT jacks, and, 
– you want to fix the conversion method to PROGRESSIVE VIDEO for video-based software.
Select this if the image is not clear when you select PROGRESSIVE AUTO.
Note that the picture will not be clear or no picture will appear if you select these settings when
either of the above conditions is not met.
xINTERLACE
Select this setting when:
–...

Getting Started
29GB
To connect the AUDIO OUT jacks of a TV to the VIDEO (AUDIO IN) jacks 
of this system
Connect a TV to the VIDEO (AUDIO IN) jacks using an audio cord (not supplied). When connecting 
a cord, be sure to match the color-coded sleeves to the appropriate jacks on the components.
 Be sure to make connections securely to avoid hum and noise.
 If your TV does not have AUDIO OUT jacks, you cannot output the TV sound from the speakers of this system.
 If you connect a TV to the VIDEO (AUDIO...

30GB
 
You can enjoy other component by connecting the VIDEO/AUDIO OUT jacks of another component.
 If you connect a TV to the VIDEO jacks in Step 3 (page 26), you cannot connect other components to the system. 
(you can connect other components with the coaxial cable (not supplied) to the COAXIAL DIGITAL IN jack 
(page 31)).
Connecting the system and the other component
Outputs the other component through the speakers of this system.
To connect the VIDEO/AUDIO OUT jacks of other component to the 
VIDEO...