Sony Dav Dz10 Operating Instructions

11GB
*1 Except for the United Kingdom models.
*2 These items are not displayed when playing a DATA CD with DivX video file.
(Except for the United Kingdom models)
 The Control Menu icon indicator lights up in green   when you select any item except [OFF] 
([PROGRAM], [SHUFFLE], [REPEAT], [A/V SYNC] only). The [ORIGINAL/PLAY LIST] indicator lights up 
in green when you select [PLAY LIST] (default setting).
[PROGRAM] (page 29)Selects the track to play in the order you want.   
[SHUFFLE] (page 31)Plays the...

12GB
Check that you have the following items:
 Speakers (5)
 Subwoofer (1)
 AM loop antenna (aerial) (1)
 FM wire antenna (aerial) (1)
 Speaker cords (6)
 Video Cord (1)
 Remote Commander (remote) (1)
 Size AA (R6) batteries (2)
 Operating InstructionsYou can control the system using the supplied 
remote. Insert two Size AA (R6) batteries by 
matching the 3 and # ends on the batteries to 
the markings inside the compartment. When 
using the remote, point it at the remote sensor   
on the...

Getting Started
13GB
Perform all connections and settings by following Steps 1 to 7.
“Step 1: Speaker System Hookup” (page 14)
“Step 2: Antenna (Aerial) Hookup” (page 18)
“Step 3: TV Hookup” (page 19)
“Step 4: Other Component Hookup” (page 23)
“Step 5: Connecting the AC Power Cord (Mains Lead)” (page 24)
“Step 6: Turning off the Demonstration” (page 24)
“Step 7: Performing the Quick Setup” (page 25)
Video signal is sent to the TV, and is output from the TV screen; audio signals are processed by this...

14GB
Connect the supplied speaker system using the supplied speaker cords by matching the colors of the 
jacks to those of the cords. Do not connect any speakers other than those supplied with this system.
To obtain the best possible surround sound, specify the speaker parameters (distance, level, etc.) on 
page 71.
Required cords
Speaker cords
The connector and the color tube of the speaker cords are the same color as the label of the jacks to be 
connected.
Step 1: Speaker System Hookup
(+)
(–)
Color...

Getting Started
15GB
Connecting the speakers
 Do not set the speakers in an inclined position.
 Do not place the speakers in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight
 Use caution when placing the speakers and/or speaker stands (not supplied) that are attached with the speakers on 
a specially treated (waxed, oiled, polished, etc.) floor, as staining or discoloration may result.
Note
SPEAKERCOAXIALFM75
Y RLAUD IO...

16GB
 Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine.
To connect the speaker cords
Connect the speaker cords after bending the bare wire at the end of the insulation. This prevents the 
speaker insulation from being inserted in the speaker terminal.
 Do not catch the speaker cord insulation in the SPEAKER jack.
Avoiding short-circuiting the speakers
Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these 
precautions...

Getting Started
17GB
2Fasten the screws to the wall.
The screws should protrude 5 to 7 mm (7/32 to 9/32 inch).
3Hang the speakers on the screws.
 Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where 
reinforcement is applied.
 Contact a screw shop or installer regarding the wall material or screws to be used.
 Sony is not...

18GB
Connect the supplied AM/FM antennas (aerials) for listening to the radio.
 To prevent noise pickup, keep the AM loop antenna (aerial) away from the system and other components.
 Be sure to fully extend the FM wire antenna (aerial).
 After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
 When you connect the supplied AM loop antenna (aerial), cord (A) or cord (B) can be connected to either terminal.
 If you have poor FM reception, use a 75-ohms coaxial cable (not...

Getting Started
19GB
First, perform the video connection, and then audio connection.
With your TV’s audio output connected to this system, you can listen to TV sound through the system 
speakers.
Connecting the video cords
Sends a played back DVD image to a TV.
Check the jacks of your TV, and choose connection method A, B, or C. Picture quality improves in 
order from A (standard) to C (component).
A To connect to a TV with the VIDEO IN jack
Connect the video cord..
B To connect to a TV with the S VIDEO...

20GB
C To connect to a TV with the COMPONENT VIDEO IN jacks
Connect a component video cord (not supplied). To use the COMPONENT VIDEO OUT jacks (Y, PB/
C
B, PR/CR) instead of the video jacks, your TV monitor must be equipped with via COMPONENT 
VIDEO IN jacks (Y, P
B/CB, PR/CR). If your TV accepts progressive format signals, you must use this 
connection and set the output channel of the system to progressive format (page 20).
When connecting to a standard 4:3 screen TV
Depending on the disc, the image...