Sony Bdv Iz1000w Operating Instructions

11GB
A"/1 (Power)
Turns the surround amplifier on/off.
BS-AIR/STANDBY indicator
You can check the status of wireless 
transmission of surround speaker audio 
signals between the main unit and surround 
amplifier.
CS-AIR ID switch
Selects the S-AIR ID.
DPAIRING button
Starts pairing.
EPAIRING indicator
Indicates the pairing status.
FSURROUND SELECTOR switch
Selects the mode for the surround amplifier.
GSPEAKERS jacks
HWireless transceiver (EZW-RT10) slot
Surround amplifier
LRSURROUND...

12GB
The buttons for system operation only are 
described below. See “Controlling Your TV or 
Other Components with the Supplied Remote” 
(page 55) for the buttons for operation of the 
connected components.
 Number 5,  , PROG +, and N buttons 
have a tactile dot. Use the tactile dot as a 
reference when operating the remote.
 Names of buttons that work after pressing the 
TV or STB operation mode buttons are 
indicated with yellow label.
A"/1 (on/standby) (pages 27, 42)
Turns on the system or sets...

13GB
MPlayback operation buttons 
See “Playback” (page 32). 
./> (previous/next)
Skip to the previous/next chapter, track, or 
file.
 (replay/advance)
Briefly replay the current scenes for 10 
seconds./Briefly fast forwards the current 
scenes for 15 seconds.
m/M (fast reverse/fast forward)
Fast reverse/fast forward the disc during 
playback. Each time you press the button, 
search speed changes.
Activates slow-motion play when pressed 
for more than one second in pause mode. 
Plays one frame at a time...

14GB
Getting Started
Step 1: Installing the System
For the best possible surround sound, place all speakers at the same distance from the listening position 
(A). The distance can be between 0.0 to 7.0 meters.
If you cannot place the center speaker and surround speakers at the same distance as (A), place them 
within 7.0 meters of the listening position.
Place the surround speakers to the rear of the listening position (B).
The subwoofer can be placed anywhere in the room.
Note Use caution when placing...

15GB
Getting Started
To add the optional surround back speakers
You can enjoy 7.1 surround sound by purchasing the Wireless Surround Speaker Kit (WAHT-SBP2, 
optional). The optional product lineup differs depending on the area.
For the position of the surround back speakers, refer the illustration below (C).
Note To use the surround back speakers, set [Surround Back] (page 53) in [Speaker Settings] to [Yes] while performing 
the Easy Setup (page 27).
4545
3030
CC
Front left speaker (L)
Front right...

16GB
Getting Started
For assembling the speakers, refer to “Speaker Installation Guide” (supplement).
To connect speaker cords to the center speaker and subwoofer
Speaker terminals are located on the rear of the speakers.
Caution
 Contact a screw shop or installer regarding the wall material or screws to be used.
 Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam and fasten them to the wall. Install the...

17GB
Getting Started
1Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. 
See the illustrations below.
2Fasten the screws to the wall.
3Hang the speakers on the screws.
30 mm 4 mm
Hole on the back of 
the speaker
5 mm 
10 mm
8 to 10 mm
219 mm
(8 5/8 inches) For the center speaker
For the other speakers
8 to 10 mm
5 mm 
10 mmHole on the back of 
the speaker
Rear of the speaker
 

18GB
Getting Started
Step 2: Connecting the System
For connecting the system, read the information on the following pages.
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other 
connections are made.
Note When you connect another component with a volume control, turn down the volume of the other components to a 
level where sound is not distorted.
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker....

19GB
Getting StartedThis connection sends a video signal to the TV.
Depending on the jacks on your TV, select the connection method.
Method 1: HDMI cable (A) connection
If your TV has an HDMI jack, connect to the TV with an HDMI cable. Picture quality will be improved 
compared to using the component video cable connection or the video cord connection.
When connecting with the HDMI cable, you need to select the type of output signal (page 59).
Method 2: Component video cable (B) connection
If your TV...

20GB
Getting Started
This connection sends an audio signal to the unit from the TV. To listen to TV sound via the system, 
perform this connection.
With a digital audio connection, the system receives a Dolby Digital multiplex broadcast signal and 
you can enjoy multiplex broadcast sound.
Note When you connect the TV and the unit with an audio cord, see “Connecting the other components” (page 21).
About Audio Return Channel (ARC)
If your TV is compatible with the Audio Return Channel function, an HDMI...