Smeg Sta6445 Instruction Manual

							 
 
User instructions   
 
 29    
 
  
 
If the dishes fail to dry or remain dull, check tha t: 
 
·  there is rinse aid inside the special container; 
·  the rinse aid dispenser setting is correct; 
·  the  detergent  used  is  of  good  quality  and  has  not  l ost  its 
effectiveness  (for  example,  through  incorrect  storage,  with  the  box 
left open). 
 
If the dishes show signs of streaking, staining, et c., check that: 
 
·  the rinse aid dispenser setting is not too high. 
 
If there are visible traces of rust inside the tank : 
 
·  the  tank  is  made  of  steel,  and  therefore  any  rust  m arks  are  due  to 
external  elements  (fragments  of  rust  from  the  water   pipes,  pots, 
cutlery, etc.). Special products are commercially available to remove 
such marks; 
·  check  that  the  amount  of  detergent  being  used  is  co rrect.  Certain 
detergents can be more corrosive than others. 
·  check  that  the  cap  of  the  salt  container  is  securel y  closed,  and  that 
the water softening setting is correct. 
       
 
  
 
If  after  following  the  above  troubleshooting  instru ctions  the  problem 
persists, call the nearest After-Sales Centre. 
 
WARNING:  any  operations  performed  on  the  appliance  by 
unauthorised persons are not covered by the warranty and shall be 
paid for by the user. 
 
  
   
     
						

							 
 
User instructions   
  
30 
4.  Troubleshooting 
 
 The  dishwasher  is  capable  of  signalling  a  number  of   faults  through  the 
simultaneous  illumination  of  several  indicator  ligh ts,  with  the  following 
meanings: 
 
FAULT DESCRIPTION 
E1  
Acquastop failure 
The  anti-flooding  system  has  been  activated  (for  th e 
relevant  models  only).  The  system  is  tripped  in  case 
of water leaks. Contact the after-sales service. 
E2  
Safety level 
The  system  which  limits  the  water  level  inside  the 
dishwasher  has  been  tripped.  Interrupt  the  program 
and switch off the dishwasher. Switch the dishwashe r 
back  on,  program  it  again  and  start  the  washing 
cycle.  If  the  problem  persists,  contact  the  after-sales 
service. 
E3  
Water heating malfunction 
The  water  is  not  heated  or  the  heating  parameters 
are  not  correct.  Repeat  the  washing  program;  if  the  
problem persists, contact the after-sales service. 
E4  
Water temperature monitoring malfunction 
Interrupt  the  program  and  switch  off  the  dishwasher. 
Switch the dishwasher back on, program it again and  
start  the  washing  cycle.  If  the  problem  persists, 
contact the after-sales service. 
E5  
Water intake malfunction 
The  appliance  does  not  take  in  water  or  does  not  do 
so  correctly.  Check  that  the  water  connections  are 
correct, the water intake tap is turned on and the filter 
is  not  fouled.  If  the  problem  persists,  contact  the  
after-sales service. 
E6  
Water pump-out malfunction 
The  appliance  does  not  pump  out  the  water  or  does 
not  do  so  correctly.  Check  that  the  drain  hose  is  not 
kinked  or  crushed  and  that  the  siphon  and  filter  ar e 
not  fouled.  If  the  problem  persists,  contact  the  after-
sales service. 
   
 
         
						

							 
 
User instructions   
 
 31 FAULT DESCRIPTION 
E7  
Turbine flow-regulator malfunction  
(for the relevant models only)  
The appliance is not able to measure the amount 
of  water  loaded  accurately.  Interrupt  the  program 
and  switch  off  the  dishwasher.  Switch  the 
dishwasher  back  on,  program  it  again  and  start 
the  washing cycle.  If  the  problem  persists, contact  
the after-sales service. 
E8  
Alternate washing system malfunction 
Interrupt  the  program  and  switch  off  the  dishwasher. 
Switch the dishwasher back on, program it again and  
start  the  washing  cycle.  If  the  problem  persists, 
contact the after-sales service. 
E9  
Water intake system malfunction 
Contact the after-sales service. 
   
 Light off  Light on  Light flashing 
 If  an  alarm  occurs  the  appliance  interrupts  the  pro gram  in  progress  and 
signals a fault. 
 ·  Alarms  E1,  E2,  E3,  E4,  E8  and E9  interrupt  the  current  program 
immediately. 
·  The  E5, E6   alarms  interrupts  the  running  program  once  the  cau se  is 
resolved, it will bring bach the execution of the p rogram. 
· The alarm  E7 is visualized at the end  of the cycle that comes,  however, 
brought to the end since the operation of the dishw asher is not harmed. 
 To “reset” an alarm is necessary:  · Open and close the door, or turn off and on the mac hine. At this point is 
possible to program the dishwasher again.  
   
 
   If the malfunction persists, contact your authorise d Service Centre.  
    
       
						

							 
 
User instructions   
  
32      TECHNICAL DATA  
Width 597 ¸ 599 mm 
Depth measured flush with the  outer edge of the control panel 550 mm 
Height (depending on models) 
Free standing: from 850 mm to 890 mm                         from 890 mm to 930 mm  Semi-integrated: from 820 mm to 890 mm                            from 860 mm to 930 mm 
Capacity 13 Standard place settings 
Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) 
Electrical characteristics See rating plate