Smeg Sta6445 Instruction Manual
Have a look at the manual Smeg Sta6445 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User instructions
9
1.2 Washing programs
Before starting a washing program make sure that:
· The water supply tap is open.
· The softener container contains regenerating salt .
· The correct amount of detergent has been added to the
dispenser.
· The baskets have been correctly loaded.
· The spray arms are able to rotate freely and without
obstruction.
· The dishwasher door is securely closed.
OPTION SELECTION
Options are selected by pressing the relative butto n by the symbol of the
option required; the light comes on to confirm that the option has been
activated.
· It is not possible to select any options when the soak
program is being used.
· All options except Flexi Tabs are disabled at the end of the
wash cycle. To disable the “Flexi Tabs” option, press the
relative button (the light goes out).
· All options, including Flexi Tabs are disabled when a
program is CANCELLED after it has begun.
ADDITIONAL OPTIONS
Some models feature additional options, activated b y pressing two
buttons simultaneously . In this case, two lines in the control panel
graphics link the symbol of the additional option t o the two buttons to be
pressed simultaneously to enable it. (e.g. “Flexi Tabs” in this
illustration)
User instructions
10
Flexi Tabs Specifically for washing with combination detergent s in tablets , which
also contain salt and rinse aid (3in1) or other agents such as glass
protector, steel rinse aids, etc. (4in1, 5in1…). Wh en this option is
selected, salt and rinse aid will not be dispensed even if the relative
compartments contain them. If the containers are em pty, the lights will
remain on.
With short programs, because there is less time for them to dissolve,
tablets may fail to wash effectively and undissolve d residues may be left.
Powder detergents are more suitable for these progr ams.
If the option is not provided , we recommend the use of conventional
products (separate detergent, salt and rinse aid), because with
conventional washing cycles, combined products migh t create problems
such as a white deposit, poor drying results and re sidues left on dishes.
For further information, refer to the detergent pack. IMPORTANT:
when no longer required, the option must be deactivated by pressing
the relative button (the light goes out).
These products are not suitable for use with excessively “hard” water.
If the hardness level set is higher than H3, when the option is activated
the relative light flashes to indicate that the pro duct is being used
incorrectly; the dishwasher will still work, but washing results may be
poor.
ULTRA CLEAN The ULTRA CLEAN program prolongs the final hot rinse to ensure a
further reduction in the bacteria level. If the tem perature in the tank falls
during this stage of the program (e.g. because the door is opened or due
to a power blackout), the light of the option and t he program lights (2) flash
to warn that the additional washing phase has not b een completed
successfully. This does not mean that the wash prog ram has been less
effective than usual.
SPREAD HALF LOAD
Suitable when there are not many dishes to be washe d, it saves energy
and reduces the program duration. Place dishes in both baskets then
load the detergent dispenser than less than the nor mal amount for a full
load.
User instructions
11
DELAYED START The start of the washing program can be delayed to program the
dishwasher to operate at the preferred time of day (e.g. overnight). Press
the PROGRAM DELAY button to activate the option and display a 1 hour
delay. Keep pressing to select the delay required, which may be up to 9,
12 or 24 hours depending on the model.
When the door is closed, the appliance will prewash the dishes, after
which the program delay set will come into effect .
CANCELLING THE CURRENT PROGRAM · To cancel the currently selected program open the door and hold
down the PROGRAM SELECTION (3) button for a few seconds
until the indicator lights for programs 4 and 5 illuminate
simultaneously (marked end).
· Close the door.
· After approximately 1 minute the dishwasher will a dvance to the end
of cycle.
CHANGING THE PROGRAM To change the program in progress, simply open the door and select a
new program. When the door is closed the dishwasher will automatically
select the new program.
TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT · Always use the dishwasher with a full load.
· Do not wash the dishes in running water.
· Use the washing program that is most appropriate for each type of
load.
· Do not carry out any preliminary rinsing.
· If available, connect the dishwasher to a hot water supply up to 60°C.
User instructions
12
TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT
THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the
environment. To avoid using excessive amounts of detergent and to save
on electricity, observe the following: · separate the more delicate items from dishes that are more r esistant
to aggressive detergents and high temperatures;
· do not pour the detergent directly on the dishes.
If the door has to be opened while washing is in pr ogress, the program
will be interrupted. The relative light will keep flashing and a beeper will
signal that the cycle has not been completed. You m ust wait about 1
minute before closing the door to restart the program. Wh en the door is
closed the program will continue from where it was interrupted. This
operation should only be carried out if strictly necessary , because it
might cause problems in execution of the program.
SWITCHING OFF
At the end of the program the beeper
sounds briefly and the lights of programs no. 4 and 5 (marked end) flash.
To switch off the dishwasher, open the door and pre ss the ON/OFF
button (1). ENERGY MANAGEMENT After 5 minutes of waiting (washing cycle completed, stopped or set but
not started) the dishwasher switches to a standby state to reduce
energy consumption .
In this state, the dishwasher indicator panel (ligh ts or display depending
on model) functions more slowly ( switch-on once every 5 seconds ).
REMOVING THE DISHES
At the end of the washing program, wait at least 20 minutes before
removing the dishes, to allow them to cool. To ensu re that any drops of
water left in the top basket cannot drip onto the d ishes still in the bottom
basket, you are advised always to empty the bottom basket first.
User instructions
13
2. Operating instructions
Once the dishwasher has been correctly installed, p repare for use as
follows:
· Adjust the water softening system;
· Add the regenerating salt;
· Add the rinse aid and detergent.
2.1 Using the water softening system
The amount of scale contained in the
water (water hardness index) can cause
whitish staining on the dry dishes, which
tend to become dull over time. The
dishwasher is equipped with an automatic
softening system which uses a special
regenerating salt to reduce the hardness
of the water.
The dishwasher is factory set for water
hardness level
3
(average hardness
41-60°dF – 24-31°dH ).
When using water of medium hardness, the regenerati ng salt container
should be refilled after approximately 20 washing cycles. The salt
container can hold approximately 1.7 Kg of salt in grains. Some models
are equipped with an optical no-salt indicator. In these models, the cap
of the salt container contains a green float which descends as the salt
concentration in the water drps. When the green flo at can no longer be
seen through the transparent cap, the container mus t be topped up with
regenerating salt. The container is situated at the bottom of the
dishwasher. After removing the lower basket, unscre w the salt container
cap by turning it anticlockwise and pour in the sal t using the funnel
supplied with the dishwasher. Before replacing the cap, remove any salt
residues from around the opening.
· When using the dishwasher for the first time, in ad dition to the salt it
is also necessary to add one litre of water to the container. · Each time the salt container is refilled, make sure that the cap is
securely closed . The mixture of water and detergent must never
penetrate the salt container, as this would comprom ise the operation
of the regeneration system. In the event of this oc curring, the
warranty will be invalidated. · Only use regenerating salt specially formulated for dom estic
dishwashers. If using salt tablets, do not fill the container
completely.
SALT
User instructions
14
· Do not use table salt as it contains insoluble substances which,
over time, may damage the water softening system.
· When necessary, refill the regenerating salt contai ner before
starting the washing program . In this way, the excess saline
solution will be immediately removed by the water; the prolonged
presence of salt water inside the tank may lead to corrosion.
Be careful not to confuse the salt and detergent pa ckages; adding
detergent to the salt container will damage the water softening system.
ADJUSTING THE WATER SOFTENING SYSTEM The dishwasher is equipped with a device which allo ws the softener
setting to be varied to suit the hardness of the ma ins water. The
hardness is set using the PROGRAM SELECTION BUTTON (3) .
To access the setting function, hold the button dow n for more than 15
seconds. The WATER HARDNESS ADJUSTMENT INDICATOR LIGHT
(4) flashes, while the SELECTED PROGRAM INDICATOR LIGHTS (2)
show the current setting. Each pressure on the butt on changes the
setting following the sequence in the table below:
>
User instructions
15
WATER HARDNESS TABLE WATER HARDNESS
SETTING German degrees (°dH) French Degrees (°dF)
0 - 4 0 - 7 All lights off (no salt)
5 - 15 8 - 25 One light on
16 - 23 26 - 40 Two lights on
24 - 31 41 - 60 Three lights on
32 - 47 61 - 80 Four lights on
48 - 58 81 - 100 Five lights on Contact your local water board for information on the hardness of your
water supply.
After adjustment or display of the current setting , simply do not touch the
button for a few seconds; the dishwasher will autom atically return to
standard mode, quitting the adjustment mode.
2.2 Using the rinse aid and detergent dispensers
The detergent and rinse aid dispensers are situated on the inner
part of the door: the detergent
dispenser is on the left, and the
rinse aid dispenser is on the right.
With the exception of the SOAK program, before every washing cycle it
is necessary to add the required amount of detergen t to the detergent
dispenser . The rinse aid, on the other hand, should only be added as
required.
User instructions
16
ADDING THE RINSE AID The rinse aid helps the dishes dry faster and
prevents the formation of scale deposits and
staining; it is automatically added to the water
during the final rinse cycle, from the container
situated on the inner side of the door.
To add rinse aid: · Open the door.
· Rotate the container cap anticlockwise by ¼ of a t urn and remove it.
· Add the rinse aid until the container is full (app roximately 140 cc).
The optical level indicator on the side of the cap should be
completely obscured. Refill the rinse aid when the optical level
indicator becomes clear again, or when the rinse ai d warning light
illuminates.
· Replace the cover and turn it in a clockwise direc tion.
· Use a cloth to remove any spillage of rinse aid wh ich might lead to
the formation of excess foam.
ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hard ness. However it
possible to change the setting by turning the dispe nser’s selector to the
desired position: the amount of rinse aid dispensed is proportional to the
selector position.
· To adjust the rinse aid setting, rotate the dispen ser cap through a
quarter turn in an anticlockwise direction and remo ve it.
· Then use a screwdriver to rotate the rinse aid sel ector to the desired
position.
· Replace the cap, turning it clockwise.
· The amount of rinse aid must be increased if the washed dishes
appear dull or feature circular stains.
· If, on the other hand, the dishes are sticky or hav e white streaks, it
is necessary to reduce the rinse aid setting.
User instructions
17
ADDING THE DETERGENT To open the detergent dispenser cap, lightly press
the button P. Add the detergent and close the cap
carefully.
During the washing cycle, the dispenser will be
opened automatically.
· When a program with hot prewash is selected (see pr ogram table),
extra detergent must be placed in the cavity G/H (depending on
models).
· Use only detergents specially formulated for dishwashers. F or optimal
washing results it is important to use a good quality detergent.
· The detergent packs must be sealed and stored in a dry place to
prevent the formation of lumps which may negatively affect washing
results. Once opened the detergent packs should not be kept for too
long, otherwise the detergent loses its effectiveness.
· Do not use detergents formulated for washing dishes by hand,
because they produce a great deal of foam and may negatively affect
the operation of the dishwasher.
· Add the correct amount of detergent. An insufficien t amount of
detergent will result in a partial removal of dirt from the dishes,
whereas an excessive amount is wasteful and does no t improve the
washing results.
· The market offers liquid and powder detergents with differing chemical
compositions, which may contain phosphates, or be phosphate-free
but contain natural enzymes .
- Detergents containing phosphates are more effective against
grease and starch at temperatures above 60°C .
- Enzyme detergents, on the other hand, are also effective a t lower
temperatures (from 40 to 55°C ) and are more easily
biodegradable. With enzyme detergents it is possibl e to obtain at
low temperatures comparable results to those which can only be
achieved at 65°C using traditional detergents.
For the safeguarding of the environment we recommen d the use of
phosphate- and chlorine free detergents.
User instructions
18
The introduction of detergent into the rinse aid di spenser, even in
liquid form, will damage the dishwasher.
2.3 General warnings and recommendations
Before using the dishwasher for the first time, it is advisable to read the
following recommendations concerning dish types to be washed and
their loading.
There are generally no constraints on the washing of domestic dishes,
but in certain cases it is necessary to take their characteristics into
account.
Before loading the dishes into the baskets it is necessary to:
· remove coarse food remains: e.g. bones, fish-bones, etc. which
may clog the filter or damage the wash pump.
· soak any pots or pans with burnt-on food remains on the bottom to
facilitate removal, then load them into the LOWER BASKET.
There is no need to pre-wash the dishes under runni ng water before
loading them into the baskets since this only wastes water.
Correct loading of the dishes helps ensure optimal washing
results.