Smeg Sap306x-9 Manual

Instructions for the User
32
8.6.2 Setting the cleaning cycle
Turn the function selection knob to select one of the
two cleaning cycles out of   and  .
To start the cleaning cycle (Pyrolysis), press 
followed by  .
Press and hold  ; press   or   to set the
duration of the cycle between a minimum of 1h 30m
and a maximum of 3h 00m (apart from the   cycle
where the duration is set at 1h 30m).
Two minutes after the cleaning cycle (Pyrolysis)
starts, a locking device which prevents opening of
the door will be...

Instructions for the User
33
9. EXTRAORDINARY MAINTENANCE
The oven may require extraordinary maintenance or replacement of parts
subject to wear such as gaskets, bulbs, etc. The following instructions describe
how to carry out these minor maintenance operations.
Before any intervention that requires access to live parts, disconnect the
power supply of the appliance.
9.1 Replacing the light bulb
If a light bulb needs to be replaced
because it is worn or burnt out (in
multifunction models remove the guide...

Instructions for the User
34
9.2 Removing the door
Open the door completely.
Insert two pins into the holes indicated
A in the two hinges towards the back of
them until they engage.
Grasp the door on both sides with both
hands, lift it forming an angle of around
30° and remove it.
To reassemble the door, put the hinges
in the relevant slots in the oven, making
sure that the grooved sections C are
resting completely in the slots.  Lower
the door and once it is in place remove
the pins from the holes in...

Instructions for the User
35
9.3 Removing the door seal
For multifunction models only:
To permit thorough cleaning of the
oven, the door seal may be removed.
There are fasteners on all four sides to
attach it to the edge of the oven. Pull
the edges of the seal outwards to
detach the fasteners.
9.4 Removing the internal glass panels
The glass in the door should always be kept thoroughly clean. To facilitate
cleaning, it is possible to remove the door (see 9.2 Removing the door) and
place it on a canvas,...

Instructions for the User
36
Removing the internal glass panel:
 Remove the internal glass panel by
pulling the rear part gently upwards,
following the movement indicated by the
arrows (1).
 Then pull the front of the glass panel
upwards (2).
 Doing this detaches the 4 pins attached to
the glass from their slots in the oven door.
Removing the middle glass panels:
(pyrolytic models)
 There are two middle glass panels in
pyrolytic models, attached using 4 small
locks. Remove the middle panels by lifting...

Instructions for the installer
37
10.INSTALLING THE APPLIANCE
10.1 Electrical connection
The identification plate bearing the technical data, serial number and brand
name is visibly positioned on the appliance.
Do not remove this plate for any reason.
The appliance must be connected to earth in compliance with electrical system
safety regulations.
If a fixed connection is being used, fit the power line with an omnipolar circuit-
breaker in accordance with the installation rules, located in a position...

Instructions for the installer
38
10.3 Inserting the fastening bushings
To fasten the appliance correctly to the
unit, insert the bushings provided onto
the front (as shown in the figure).
Once the appliance is in place, fasten it
to the unit using the screws. The
bushing enables the screw to be angled
by approximately 30°.
After fastening the appliance, cover the
bushing with the caps provided. 

Instructions for the installer
39
10.4 Positioning the oven
Never use the oven door to lever the oven into place when fitting. Avoid exerting
too much pressure on the oven door when open.
It is recommended to install the oven with the help of a second person.
The base on which the oven is resting must be complete as shown in the
illustrations below.
The oven is designed for
mounting into any piece of
furniture as long as it is heat-
resistant. The adjacent figure
shows the indicative overall
dimensions...

Instructions for the installer
4010.4.1 Positioning under a work top
         
10.4.2 Installing in tall units
                   
583-585
490-500
560 60
35-40
583-585
560