Smeg Sac399x8 Manual

Instructions for the user
33
10.5 Cleaning the inside of the oven
For the best oven upkeep, clean it regularly after having allowed it to cool. 
•  Take out all removable parts.
•  Clean the oven racks with hot water and non-abrasive detergent. Rinse and
dry.
•  For easier cleaning, the door can be removed (see “11.2 Removing the
door”).
The oven should be operated at the maximum heat setting for 15/20 minutes
after use of specific products, to burn off the residues left inside the oven.
When the...

Instructions for the user
34
10.6 Removing guide frames
Removing the guide frames makes it easier to clean the side parts of the oven, and it
also needs to be done whenever the automatic cleaning cycle is used (only available
on some models).
•  To remove the guide frames, pull the frame towards the inside of the oven to
unhook it from its housing 
A, then slide it out of the seats at the back B.
•  When cleaning is complete, repeat the above procedures in reverse order to put
the guide frames back in....

Instructions for the user
35 10.7.1 Before starting the automatic cleaning cycle
Pyrolysis may be carried out at any time of the day or night (if you wish to benefit
from the lower cost of electricity overnight).
•  Completely remove all accessories
from inside the oven, including the
upper guard.
•  Remove the guide frames, see “10.6
Removing guide frames”.
•  At the end of the cleaning cycle, when
the oven has cooled down, reinsert
the frames by repeating the previously
used procedure in reverse...

Instructions for the user
3610.7.2 Setting the automatic cleaning cycle 
(pyrolysis - on some models only)
•  Position the oven function selector to the pyrolysis function symbol  .
•  The programmer automatically sets
the minimum duration of the cleaning
cycle (2 hours).
•  Within 5 seconds press key   or
 to increase or decrease the cycle
time (the maximum time is 3 hours
and 30 minutes). The set minutes will
be shown by the internal segments of
the clockface lighting up, while the
hours will be shown...

Instructions for the user
37
10.8 Vapor Clean: assisted cleaning (on some models only)
Vapor Clean is an assisted cleaning procedure which facilitates the removal of
dirt. Thanks to this process, it is possible to clean the inside of the oven very
easily. The dirt residues are softened by the heat and water vapour to make it
easier to remove them afterwards.
Before starting the assisted cleaning cycle, make sure that the oven does not
contain any foods or large spills from previous cooking operations....

Instructions for the user
38•  Pour approx. 40 cc of water onto the
floor of the oven (as shown in the
illustration). Make sure it does not
overflow out of the cavity.
•  Spray a water and washing up liquid
solution inside the oven using a spray
nozzle. Direct the spray against the
side walls, roof, base and deflector. 
•  At the end of this process, close the
door and set the cleaning cycle.
Do not spray excessive amounts of the water and washing up liquid solution. We
recommend spraying approx. 20...

Instructions for the user
39 10.8.2 Setting the assisted cleaning cycle
Once the preparations have been made for the assisted cleaning cycle, proceed
as follows:
•  turn the oven function knob and the oven thermostat knob to 
 for the
Vapor Clean function;
•  set a cooking time of 18 minutes using the cooking duration procedure
described in more detail in “7.1.3 Programming”;
•  The assisted cleaning cycle will start approx. 6 seconds after the user last
makes a setting change to the electronic analogue...

Instructions for the user
40
11. EXTRAORDINARY MAINTENANCE
The oven may require extraordinary maintenance or replacement of parts
subject to wear such as gaskets, bulbs, etc. The following instructions describe
how to carry out these minor maintenance operations.
Before any intervention that requires access to live parts, disconnect the
power supply of the appliance.
If a problem cannot be resolved through ordinary maintenance or in the case of
other types of fault, contact your local technical support...

Instructions for the user
41
11.2 Removing the door
11.2.1 With pins
Open the door completely.
Insert two pins into the holes indicated A
in the two hinges towards the back of
them until they engage.
Grasp the door on both sides with both
hands, lift it forming an angle of around
30° and remove it.
To reassemble the door, put the hinges in
the relevant slots in the oven, making sure
that grooved sections C are resting
completely in the slots.  Lower the door
and once it is in place remove the pins
from...

Instructions for the user
42
11.3 Removing the door seal
For multifunction models only:
To permit thorough cleaning of the oven,
the door seal may be removed.
There are fasteners on all four sides to
attach it to the edge of the oven. Pull the
edges of the seal outwards to detach the
fasteners.
11.4 Removing the internal glass panels
The glass in the door should always be kept thoroughly clean. To facilitate
cleaning, it is possible to remove the door (see 11.2 Removing the door) and
place it on a...