Smeg Pgf75-4 Manual

Contents   
19 
1 INSTRUCTIONS FOR SAFE AND PROPER USE _______________  20 
2 POSITIONING OF THE HOB _______________________________  22 
3 ADJUSTMENT TO DIFFERENT TYPES OF GAS _______________  28 
4 FINAL OPERATIONS _____________________________________  30 
5 USING THE HOB ________________________________________  31 
6 CLEANING AND MAINTENANCE ___________________________  33 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE IDENTIFICATION SYMBOLS APPEAR ON...

 Introduction 
 
20 
1 INSTRUCTIONS FOR SAFE AND PROPER USE 
 THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND 
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE 
PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE 
READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE 
USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. 
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN 
ACCORDANCE WITH THE REGULATIONS IN FORCE.  THIS APPLIANCE IS 
INTENDED FOR DOMESTIC USES AND...

Introduction   
21 
 THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION 
NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER 
THE SAFETY COVER.  
THE DATA PLATE ON THE PROTECTIVE COVER MUST NEVER BE 
REMOVED. 
 
 DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS 
ON THE HOB PANSTAND GRIDS. 
 
 
 DO NOT USE COOKING RECEPTACLES THAT EXTEND BEYOND THE 
OUTSIDE PERIMETER OF THE HOB. 
 
 
 THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW 
CHILDREN TO GO NEAR OR PLAY WITH...

 
 
Instructions for the installer 
  
22 
2 POSITIONING OF THE HOB 
 
The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood, as long as they are heat-resistant (T 90°C).
2.1 Attachment to support structure, traditional built-in 
model 
Create an opening with the dimensions shown in the figure in the work surface. 
 
 
A (mm) B (mm) C...

 
 
Instructions for the installer  
 
23  2)   
    3)    
4)   
 
 
2.2 Attachment to support structure, flush-mounting model  
Create an opening with the dimensions shown in the figure. 
 
 
 
A (mm) B (mm) C (mm) D (mm) E (mm) L (mm) X (mm) Y (mm) 
min 110 min 460 min 750 20÷40 min 50 700 492 700 
 
This type of appliance also requires a cut 3 mm deep in the work-top 
with the dimensions shown in figure 4 (detail A, figure 2). 
Before positioning the hob, position the adhesive sponge material “E”...

 
 
Instructions for the installer 
  
24  2) 
      
3)
 
4) 
3A
      
  
Apply a layer of “waterproof primer” to the milled surface. 
   
  
Important: Other types of installation will only be possible under the
manufacturers supervision. 
   
Overall dimensions: location of gas and electrical connection points (all 
measures in mm). 
 
Warning: the bottom surface of the hob can become very hot. 
To avoid a hazard, under-bench access must be restricted. 
Refer to installation instruction  

 
 
Instructions for the installer  
 
25 
IMPORTANT: when installing the appliance above a cupboard, a dividing 
shelf, as shown above, must be installed. 
If installed above an under-bench oven, this is not required. 
Installation of an oven without cooking fan underneath the hob is 
forbidden. 
 
 
2.3 Electrical connection 
 Make sure that the voltage and capacity of the power supply cable conform 
to the data shown on the plate located under the protective cover. Do not 
remove this plate for any...

 
 
Instructions for the installer 
  
26 
  
If the power cable is to be replaced, 
the wire section on the new cable must 
not be less than 0.75 mm2 (3 x 0.75 
cable), bearing in mind that the end to
be connected to the appliance must 
have the earth wire (yellow-green) at 
least 20 mm longer.  Use only H05V2V2-F cable or similar which has a maximum temperature of 
90°C.  Any replacement needed should be carried out by a specialised 
technician who should make the mains connections according to the...

 
 
Instructions for the installer  
 
27 
2.6 Gas connection 
Connection to the gas mains may be made with a rigid copper pipe  or 
with a flexible pipe  conforming to the provisions defined by standard 
regulations in force.  
After connection operations, check for leaks using a soapy solution.  
The hob has been inspected for G20 natural gas (2H) at a pressure of 20 
mbar. For use with other types of gas, see chapter “3. ADJUSTMENT TO 
DIFFERENT TYPES OF GAS. The hose connection at the rear of the...

 
 
Instructions for the installer 
  
28   
3 ADJUSTMENT TO DIFFERENT TYPES OF GAS  
  
Before performing any cleaning or maintenance work, unplug the 
appliance from the mains. 
   
  The hob is set for natural gas G20 (2H)  at a pressure of 20 mbar.  In the 
case of functioning with other types of gas the burner nozzles must be
changed and the minimum flame adjusted on the gas taps. To change the 
nozzles, proceed as described below. 
   
  
3.1 Replacement of nozzles on the hob    
  1.  Remove the...