Smeg A3-6 Manual

Contents  
 
1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 44 
2. INSTALLING TH E APPLIANCE _____________________________ 46 
3. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 50 
4. FINAL OPERATIONS _____________________________________ 52 
5. DESCRIPTION OF CONTROLS ____________________________ 54 
6. USING THE COOKING HOB _______________________________ 61 
7. USING THE OVENS______________________________________ 63 
8. AVAILABLE ACC ESSORIES _______________________________ 65 
9....

 Introduction 
 
1.  INSTRUCTIONS FOR SAFE AND PROPER USE 
 
 
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND 
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE 
PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE 
READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE 
USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. 
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN 
ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS 
INTENDED FOR DOMESTIC USES...

Introduction   
  
DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO 
TOUCH THE HEATING ELEMENTS INSIDE THE OVEN. 
 
  
 
DO NOT INSTALL THIS APPLIANCE ON A RAISED PLATFORM.   
  
DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS 
ON THE COOKING HOB PAN STANDS. 
 
  
DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE 
OUTER PERIMETER OF THE HOB. 
  
  
THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING 
CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN...

 
 
Instructions for the installer 
 
46 
2. INSTALLING THE  APPLIANCE  
 
It is the law that all gas appliances are installed by  competent persons. Corgi gas installers are approved to work to safe and satisfactory standards. All gas installation, servicing and repair work must be in accordance with the gas safety regulations 1984 (installation and use) as amended 1990.  It can be placed against walls higher th an the hob, at a distance of at least 50 mm from the side of the appliance, as shown in the...

 
Instructions for the installer  
   
2.2 Electrical connection 
 
Make sure the voltage and the cross-section of the power supply line 
match the specifications indicated on the identification plate positioned in 
the storage compartment.  
Do not remove this plate for any reason. 
  
 
The plug at the end of the power cabl e and the wall socket must be the 
same type (conforming to regulations in force). Check that the power line 
is adequately grounded. Do not us e reducers, adapters or shunts....

 
 
Instructions for the installer 
 
48  
  
 For operation on 380-415V3N∼: use 
a H05RR-F-type five-core cable (5 x 
1.5 mm2). 
 
 
 
 
For operation on 380-415V2N∼: use 
a H05RR-F-type four-core cable (4 x 
2.5 mm2). 
 
 
 
 
 
 
For operation on 220-240V∼:use n 
H05RR-F-type three-core cable (3 x 4 
mm2). 
 
The cable end to be connected to the 
appliance must be provided with a 
ground wire (yellow-green) at least 20 
mm longer. 
 
  
 
 The manufacturer cannot  be held liable for damage to persons...

 
Instructions for the installer  
  
2.3 Ventilation requirements 
  
The room containing the appliance should ha ve an air supply in accordance with 
B.S. 5440 part 2 1989. 
1. All rooms require an opening window or equivalent, and some rooms will require a permanent vent as well. 
2. For room volumes up to 5 m3 an air vent of 100 cm2 is required. 
3. If the room has a door that opens directly to the outside, and the room exceeds 1 m3 no air vent is required. 
4. For room volumes between 5 m3 and 10...

 
 
Instructions for the installer 
 
50 
3.  ADAPTATION TO DIFFERENT TYPES OF GAS 
  
  
Before carrying out the following operations, disconnect the appliance 
from the electricity supply. 
 
The cooking hob of the co oker is preset for G20 natural gas at a 
pressure of 20 mbar. In the case of  functioning with other types of gas the 
burner nozzles must be changed and the minimum flame adjusted on the 
gas taps. Replace the burner nozzles as  indicated in the table of the gas 
to be used. 
 
3.1...

 
Instructions for the installer  
  
 
3.2 Burner and nozzle characteristics table 
  Burner Rated heating capacity (kW) 
 
LPG – G30/G31  28/37 mbar (drawing ref. X238)  
  Nozzle diameter1/100 mm Reduced capacity (W) 
Capacity  g/h G30 Capacity  g/h G31 
Auxiliary 1.05 50 400 76 75 
Semi rapid 1.8 65 500 131 129 
Rapid 3.0 85 800 218 214 
Fish Burner 1.9 68 800 138 136 
Ultra rapid 3.9 100 1600 284 279       Burner Rated  heating  capacity (kW) 
 
NATURAL GAS – G20  20 mbar 
  Nozzle diameter 1/100...

 
 
Instructions for the installer 
 
52 
4. FINAL OPERATIONS 
 
After replacing the nozzles, repositi on the flame-spreader crowns, the 
burner caps and the pan stands. 
 
 
 Following adjustment to a gas other than the preset one, replace the gas 
adjustment label fixed to the appliance with the one corresponding to the 
new gas. This label is in the packet together with the nozzles.   
 
4.1  Adjustment of minimum for natural gas 
Light the burner and turn it to the minimum 
position 
. Extract the...