Singer Serger Professional 5 Manual

 
   
  
 4. While holding the thread firmly, pu ll the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
   
  5. Turn the handwheel toward you unt il the lower looper extends 5-10mm  
       (approximately ½ inch ) from the needle plate edge.  
 
  6. Thread the looper area of the mach ine following the red color coded  
       thread guides 4-10.  
 
 
 
  7. Place the thread slighty from left and  
      to the ri ght of threading guide  f. 
 
 
 
 
  8. Place the thread slightly from the...

 
   
 Three-Thread Rolled Hem Page 10  
 10. Thread the looper eye (A)  from front to back.  Pull about 4 inches of thread. 
                 Position thread into V cutout (B) on thr eader.  Firmly hold thread tail with left   
                  hand and pull Threader lever (C) up into place (D).  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  NOTE: Make sure the Upper Looper thread is 
behind the Lower Looper thread. 
Threader Lever 
“V” cutout   

 
  
  5. Continue to thread point s 4-8.  Slip the thread into the rear slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the right  slots of the thread guides i and  j.  
 
  8. Before threading the eye of the needl e, make sure the thread is    
               behind
 the thread guide located on t he bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
  
 
  
 
  
  9. Draw about 4 inches of the thr ead through the needle eye...

 
   
   
   
  
                   
 
                                   
Chapter 15: 
                
Additional Presser Feet 
 
   
 
 
 
 
 
 
 
 
 
      
 
                             
 
 
 
 
 
 
 
 
 
                                        

 
   
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
 
 
             
 
 
 
 
 
 
 
 
 
         
          Additional Presser Feet page 1 
BLIND HEM FOOT 
The Blind Hem Foot is used for hemming skirts, pants and other sewing projects 
in one easy operation.  It is recommended fo r use on stretch or textured fabrics. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
     
Machine Preparation 
•  Differential Feed:    Set to “N” 
•  Needles:      Use the right needle only 
•  Upper Knife:  Engaged 
•  Stitch Length:...

 
   
   
  
 
 
 
 
 
 
 
 
 
      
 
 
 
 
 
 
 
 
 
 
             
 
 
 
 
 
 
 
 
 
         
          Additional Presser Feet page 2 
CORDING FOOT 
The Cording Foot is used for sewing piping (cording) between two layer\
s of  fabric in one easy operation. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Machine Preparation 
•  Differential Feed:   Set to “N” 
•  Needles:     You may use both the right and left needle, or left only 
•  Upper Knife:  Engaged 
•  Stitch Length:  Set to “N” 
•  Foot:...

 
   
   
 
 
          Additional Presser Feet page 3 
ELASTIC FOOT 
The Elastic Foot is used for inserting elastic into a seam.  It can be used for  
swimwear, lingerie and other sewing projects. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Machine Preparation 
•  Differential Feed:    Set to “N” 
•  Needles:      Use both the right & left needle for wider elastic, right needle for narrow   
•                                   elastic 
•  Upper Knife:    Engaged 
•  Stitch Length:    Set to 3 or 4 
•...

 
    
   
  
 
BEADING FOOT 
The Beading Foot is used for sewing on beads, sequins, pearls and thick cord. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Machine Preparation 
•  Differential Feed:    Set to “N” 
•  Needles:      Use left needle for large beads, or right needle for smaller beads 
•  Upper Knife:    You may choose to work with or without the upper knife (If engaging 
      the knife, be careful not  to cut the beads as you sew) 
•  Stitch Length:    Set to 3 or 4 
•  Foot:      Attach (snap-on)...