Sim2 Multimedia Projector Ht5000 User Manual


ht5000

Sets the unit to stand-by.
Activates the On Screen Display menus and allows navigation thought the various pages.
▲,▼,◀,▶
Navigates between the On Screen Display menus and parameter adjustments.
Calls up the  Source Selection menu.
1  REMOTE CONTROL AND KEYPAD
KEYS 0-9Select the sources directly. Switches on from Standby.
STAND-BYSets the projector to stand-by .
ESCAPEDeactivates the On Screen Display.
UP/DOwN/LEfT/RighT ARROw KEYS
Navigates between the On Screen Display menus and...


ht5000

Different input signal resolutions can be adapted to match the specified screen  resolution  without  loss  of  image  quality,  thanks  to  a  generous selection of preset aspect ratios, some of which are user definable.
All picture adjustments can be made with the remote control interac-ting with a simple menu-activated On Screen Display; alternatively, the projector can be controlled by a domestic automation system via its serial port, by a USB 1.1 connection or by ethernet RJ45...

4
ht5000

CAUTiONTo reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing th\
e top cover of the projector.For technical assistance refer to trained personnel authorised by the man\
ufacturer.
Read all chapters of this manual carefully before switching on the projector. This manual provides basic instructions for using the hT5000 
system.  installation, preliinary adjustments and procedures that necessitate the removal of the top cover and contact with...

5
ht5000

fCC STATEMENT
CLASS B PRODUCT
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates,  uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio...

6
ht5000

•  Read this manual carefully and keep it in a safe place for future consultation.
  This  manual  contains  important  information  on  how  to 
install  and  use  this  equipment  correctly.  Before  using  the equipment, read the safety prescriptions and instructions carefully. Keep the manual for future consultation.
•   Do not touch internal parts of the units
  Inside  the  cabinet  there  are  electrical  parts  carr ying 
dangerously  high  voltages  and  parts  operating  at  high...

7
ht5000

 Install the unit as close to the wall socket as possible. Avoid 
stepping on power cables, make certain they do not be-
come tangled, and never jerk or tug them; do not expose 
them to sources of heat, and make sure they do are not 
knotted or crimped. If the power cables become dama-
ged, stop using the system and request the assistance of 
an authorised technician.
•  Disconnect the unit from the mains power supply in the 
event of electrical storms and when not in use.
  To  prevent...

8
ht5000

3  UNPACKiNg
To  remove  the  HT5000  system  from  its  carton  follow  the 
diagrams (Fig. 1).
for reason of the elevated weight of projector it reccom
-
mend to unpack the projector at least in 2 persons.
CONTENTS Of PACKA gE
- the projector
- Remote control 
- four 1.5V AAA batteries (for remote control)
- three power cables (EU, UK, USA) for the projector
- the user manual.
If anything is missing, immediately inform your dealer.
Remote Control
4 1.5V AAA batteries
Power cables(EU, UK,...

9
ht5000

Fig. a
Position the projector on a stable, suitable platform or utilise the 
optional bracket for a fixed ceiling installation.
wARNiNg:  if  using  the  ceiling  mount  bracket,  scrupulously 
observe  the  safety  instructions  included  with  the  bracket 
itself. if  using  a  bracket  other  than  that  supplied  by  SiM2 
Multimedia, make sure that the projector is at least 65 mm 
below the ceiling and that the bracket does not obstruct the 
air vents (intake and outlet).
If the...

10
ht5000

 
KEYSTONE
20%
  
The  Orientation  adjustment  in  the  Set  up  menu  allows  you  to 
reverse  the  image  vertically  and  horizontally  (Fig.  9),  to  allow 
the projector to be used for desktop front, ceiling front, desktop 
rear and ceiling rear installations (Fig. 5). 
To  activate  an  electric  motorised  screen  a TRig 1  output  is 
provided at the rear of the projector (Fig. 6).
The  output  is  activated  (Voltage:  1V)  when  the  projector  is 
switched on and is...