Sim2 Multimedia Projector Ht3000 User Manual

460.554.000
ht3000

2
ht3000

MENUSOURCEESC

Sets the unit to stand-by.
Activates the On Screen Display menus and allows navigation though the various 
▲,▼,◀,▶
Navigates between the On Screen Di-splay menus and parameter settings.
Calls up the  Source Selection menu.
Deactivates  the  On  Screen 
1  REMOTE CONTROL AND KEYPAD
KEYS 0-9Select the sources directly. Switches on the panel from Standby.
STAND-BY / ONSets the panel to stand-by .
ESCAPEDeactivates the On Screen Display.
UP/DOWN/LEFT/RIGHT ARROW KEYSNavigates...

3
ht3000

Different input signal resolutions can be adapted to match the specified screen  resolution  without  loss  of  image  quality,  thanks  to  a  generous selection of preset aspect ratios, some of which are user definable.
All picture adjustments can be made with the remote control interac-ting  with  a  simple  menu-activated  On  Screen  Display;  alternatively, the  projector  can  be  controlled  by  a  domestic  automation  system via its serial port.
The appliance has been subjected to...

4
ht3000

CAUTIONTo reduce the risk of electric shock, disconnect the power supply cable on the rear panel before removing th\
e top cover of the projector.For technical assistance refer to trained personnel authorised by the man\
ufacturer.
Read all chapters of this manual carefully before switching on the projector. This manual provides basic instructions for using the HT3000 system. Installation, preliinary adjustments and procedures that necessitate the removal of the top cover and contact with...

5
ht3000

•   Read this manual carefully and keep it in a safe place for future consultation.  This  manual  contains  important  information  on  how  to install  and  use  this  equipment  correctly.  Before  using  the equipment, read the safety prescriptions and instructions carefully. Keep the manual for future consultation.
•   Do not touch internal parts of the units  Inside  the  cabinet  there  are  electrical  parts  carr ying dangerously  high  voltages  and  parts  operating  at  high...

6
ht3000

•  Changing the fuses.
  Before changing the fuse disconnect the unit from the 
mains power supply.
 The  fuse  compartment  is  next  to  the  power  supply  con-
nector (Fig. 3). Remove the fuse holder (2) with a flat head 
screwdriver and replace the fuse (3). Fit a new spare fuse 
(4). Use only T 5A H fuses.
Fig.3
•   Be careful with cables.
  Make certain cables are routed so that people will not be 
impeded or tripped up.
  Keep all cables away from children. 
  Install the unit as close...

7
ht3000

1
2
3
4

3  UNPACKING
To remove the HT3000 system from its carton follow 
the diagrams (Fig. 4).
Keep  the  carton  for  use  when  transporting  or  ship-
ping the unit.
Fig.4
CONTENTS OF PACKAGE
Instruction manual
Remote Control
1.5 V AAA batteries
Power cable Europe, UK, US
Projector
Lens shift key
Fig.5
- the projector
- Remote control 
- four 1.5V AAA batteries (for remote control)
- three power cables (EU, UK, USA) for the projector
- the user manual.
- Lens shift key
If anything is...

8
ht3000

Position the projector on a stable, suitable platform or utilise the 
optional bracket for a fixed ceiling installation.
WARNING:  If  using  the  ceiling  mount  bracket,  scrupulously 
observe  the  safety  instructions  included  with  the  bracket 
itself.  If  using  a  bracket  other  than  that  supplied  by  SIM2 
Multimedia, make sure that the projector is at least 65 mm 
below the ceiling and that the bracket does not obstruct the 
air vents (intake and outlet).
If the projected...


ht3000

+12VUSB 1.1R/CrCONTROL (RS232)GRAPHICS RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMOTE32S-VIDEOMENUESCINPUT154
0IHDMI 26

To  activate  an  electric  motorised  screen  a  12  Volt  output  is 
provided at the rear of the projector (Fig. 10).
The output is activated (Voltage: 12 Vdc) when the projector is 
switched on and is de-activated (no Voltage output) when the 
projector is in stand-by mode.
You can also use black motirised curtains to delimit the screen 
when the projected image aspect...

10
ht3000

5   SWITCHING THE PROJECTOR ON AND OFF
WARNING: Connect the projector to a power supply with a 
nominal voltage within the following values: 100-240 V AC, 
50/60 Hz. It must be earthed (Fig. 12).
GRAPHICS RGBHVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
2S-VIDEO
MENU
ESCINPUT
1
5
4
0I
Power Switch:Position I: OnPosition 0: Off
FusedPower Socket
Power Plug
 
Fig. 12
In position I the projector will initialise itself  (red and green leds 
on) and then goes into standby mode (red led on) (Fig. 13).
HDMI 1...