Siemens Se 20t593 Eu Instructions For Use

en21
Programme overview
Soups, 
soufflés,  sauces, 
potatoes,  pastries, 
rice, eggs,  fried food Soups,
potatoes, pastries,
rice, eggs, fried food Coffee,
cake, milk,
sausage, cold drinks,saladsRinse if the
utensils have been left for
several days
prior to wash-
ing in the dish washer
Large -> small
AUTO
SUPER WASH AUTO
DELICATE WASH QUICK
WASH PRERINSE
ONLY
AUTO WASH
Type of utensil e.g. porcelain,pans, 
cutlery, glasses,etc.
Hard-
wearing Mixed
Fragile
Mixed
Type of food remainse.g. Amount of food...

en
22
Programme  data 
The programme data (duration, energy and water consumption) can be found in the summary of instructions and refers to standard conditions. Greater deviations may be caused by:
different quantities of utensils
inlet temperature of the water
water pressure
ambient temperature
mains voltage tolerances
and appliance-specific tolerances (e.g. temperature, water flow rate, etc.)
Only ranges can be indicated for the automatic programmes. The water consumption values refer to water...

en23
Timer programming 
You can delay the programme start by 24 hours in steps of 
 minutes.
If the option “Time Pre-select” is chosen the display shows “Delay start: 00 mins”.
Set the desired time.
Return to the Main Menu by pressing M/OK 
2  and start the required
programme by pressing the Start Button
4 .
Close the door. This starts the time counting backwards.
When the set time has elapsed the 
programme will start automatically.
Until the programme starts you are able to change the set time and...

en
24
Buzzer Volume 
You can vary or even completely 
switch off the volume of the acoustic end-of-programme signal.
If the option “Buzzer Volume” is chosen the display shows “Buzzer 6” (factory setting).
You can change this value to 0 
(acoustic signals switched off) or to values between 1 (quiet) and 6 (loud). 
A short buzz demonstrates the currently chosen volume level.
Adding Rinse Aid 
You can set the amount of rinse aid added.
If the option “Adding Rinse Aid” is chosen the display shows “Rinse Aid...

en25
Standard Programmes In addition to the rinse programmes available in the Main Menu you can choose among the following standard programmes from the programme “Normal”:
Extra,Eco 50, Eco 45, Normal 45.
Set the desired programme and start the selected programme by pressing the Start Button 
4.
If you do not want to use any of the displayed standard programmes return to the Main Menu by using the button M/OK 
2.
If you want to cancel the selection of a standard programme in the Main Menu press the...

en
26
Remote Options ** 
The dishwasher installs itself automatically during the first use within a serve@Home 
network. In some cases however, it might become necessary to start the enrolment 
process anew.
If the option “Remote Options” is selected, the message “Enrol Device” will be displayed. By pressing the button + 
3
 you enrol the device
again at the gateway. After successfully enrolling the device the message 
“Auto Wash” will be displayed.
If the enrolment is unsuccessful the display shows “no...

en27
Interrupting the programme
In order to interrupt the programme, 
open the door. In order to avoid water escaping, only open the door slightly first. The message “Cancel Programme” will be displayed, alternating with the message “Close the door”, the remaining programme time, the selected programme, and the current programme phase.
In order to interrupt, do not in any circumstance press the button – 
3
“Cancel Programme” because this will not allow the programme to continue!
To continue the...

en
28 Information on 
programme sequence
When the appliance starts, the following displays are indicated.
Prerinse The utensils are washed in this part of the programme without detergent. Finished in X:XX hrs Indicates the remaining running time of the programme. Prerinse
Finished in X:XX hrs
Wash 
The utensils are washed optimally with 
detergent and heated water. Wash
Finished in X:XX hrs
Final Rinse 
Rinse aid is automatically added to prevent water stains on the utensils. Final Rinse
Finished in X:XX...

en29
Information on 
programme sequence
Ready 
The programme has ended. The utensils can now be removed.
End
Sensors At the start of every programme all 
sensors (temperature sensor, Aqua 
sensor, motor sensor) are tested.Sensors working
correctly
Remaining time is being recalculated 
The expected programme duration is recalculated according to the quantity and soiling of the utensils. 
Auto Wash 
The currently selected programme is displayed.
Auto Wash
Remaining time is
being recalculated
    

en
30 Information on 
onboard computer
Hygienic washing** When the symbol is displayed, the utensils are hygienically clean. Keep the door closed, otherwise hygienic washing is not guaranteed. 
Glass protection system** Special gentle treatment of glass; in all programmes. 
Heat exchanger** 
Saves energy by recovering heat for the next rinse cycle; in all programmes.
Spray pressure** 
Symbol indicates the different spray pressures in the system.
Normal 
spray active
Hygienic washing is active
Glass...