Siemens Se 20t593 Eu Instructions For Use
Have a look at the manual Siemens Se 20t593 Eu Instructions For Use online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 428 Siemens manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
en21 Programme overview Soups, soufflés, sauces, potatoes, pastries, rice, eggs, fried food Soups, potatoes, pastries, rice, eggs, fried food Coffee, cake, milk, sausage, cold drinks,saladsRinse if the utensils have been left for several days prior to wash- ing in the dish washer Large -> small AUTO SUPER WASH AUTO DELICATE WASH QUICK WASH PRERINSE ONLY AUTO WASH Type of utensil e.g. porcelain,pans, cutlery, glasses,etc. Hard- wearing Mixed Fragile Mixed Type of food remainse.g. Amount of food remains Condition of food remains Wash programme Programme progress Very small Very adhesive Slightly adhesive The programme progress is optimised and adjusted according to the appliance load and degree of soiling on the utensils. Drying Prerinse Clean Intermedi- ate wash Final wash 60 – 70 45 – 55 35 – 45 45
en 22 Programme data The programme data (duration, energy and water consumption) can be found in the summary of instructions and refers to standard conditions. Greater deviations may be caused by: different quantities of utensils inlet temperature of the water water pressure ambient temperature mains voltage tolerances and appliance-specific tolerances (e.g. temperature, water flow rate, etc.) Only ranges can be indicated for the automatic programmes. The water consumption values refer to water hardness value 4. Selecting options/ standard settings Operating principle From the Main Menu you can select the following options/settings by repeatedly pressing the button M/OK 2 : Timer programming Remote Control** Reduce TimeOnboard computer Drying Level Buzzer Volume Adding Rinse Aid Water HardnessLanguageStandard Programmes Remote Setting** ** Only with installed serve@Home interface Within an option/basic setting there are several possible settings that can be selected using the buttons – or + 3 . A selected setting is applied by changing to the next option/basic setting using the button M/OK 2. If a setting has been changed using the buttons – or + and stored using M/OK 2, the message “Value Stored” will be displayed and the display returns to the Main Menu.
en23 Timer programming You can delay the programme start by 24 hours in steps of minutes. If the option “Time Pre-select” is chosen the display shows “Delay start: 00 mins”. Set the desired time. Return to the Main Menu by pressing M/OK 2 and start the required programme by pressing the Start Button 4 . Close the door. This starts the time counting backwards. When the set time has elapsed the programme will start automatically. Until the programme starts you are able to change the set time and programme. To do this, use the button – 3 to return to the Main Menu and change the settings. Then start the programme again. In order to delete the pre-selected time, set the time back to “Delay start: 00 mins”. Remote Control** After choosing the option “Remote Control” the display will show “Remote Control: Off” (factory setting) You activate this option by selecting “Remote Control: On”. ** Only with installed serve@Homeinterface Reduce Time The Auto Programmes allow you to reduce the run time of the programmes. However, in order to achieve an optimal cleaning result, the water and energy consumption will be increased. If the option “Reduce time” is chosen the display shows “Reduce time: Off” (factory setting). Select “Reduce time: On”. Return to the Main Menu by pressing M/OK 2 and start the required programme by pressing the Start Button 4 . If you do not want to use “Reduce time” the next time you use the dishwasher, you must deselect this option. Onboard computer If the “Onboard computer on” option is activated, the following displays are indicated in succession according tothe selected programme: “Normal spray active” / “Gentle spray active” / “Intensive spray active” “Hygienic washing” “Glass protection system is active” “Heat exchanger is active”. If the onboard computer option is selected, “Onboard computer off” is displayed(factory setting). Select “Onboard computer on”. If you no longer wish additional information to be displayed during the next rinse cycle, you must switch the option off again. Drying Level If the option “Drying Level” is chosen the display shows “Normal drying” (factory setting). Alternatively you can select “Eco drying” or “Extra drying”. The option “Extra drying” increases the temperature during rinsing in all programmes. (Please take care withdelicate dishes.)
en 24 Buzzer Volume You can vary or even completely switch off the volume of the acoustic end-of-programme signal. If the option “Buzzer Volume” is chosen the display shows “Buzzer 6” (factory setting). You can change this value to 0 (acoustic signals switched off) or to values between 1 (quiet) and 6 (loud). A short buzz demonstrates the currently chosen volume level. Adding Rinse Aid You can set the amount of rinse aid added. If the option “Adding Rinse Aid” is chosen the display shows “Rinse Aid 4” (factory setting).Change this setting only if there are streaks (reduce the value) or water stains (increase the value) remaining on the dishes. You can choose a value between 0 and 6. Water Hardness Before starting the appliance for the first time or in case of changes in the water hardness, the dishwasher’s softening system must be set to the hardness of your mains water supply. Follow the instructions set out in the chapter “Set-up of the Softening System”. Language You can change the language selected when the appliance was started for the first time (see chapter “Before Starting The Device For The First Time”). If the option “Language” is chosen the display shows several language abbreviations. The abbreviation of the currently selected language is flashing. In order to choose a different language, press – or + 3 until the desired language appears. Confirm the language selection by pressing M/OK 2 . All following optical character messages will be displayed in the selected language.
en25 Standard Programmes In addition to the rinse programmes available in the Main Menu you can choose among the following standard programmes from the programme “Normal”: Extra,Eco 50, Eco 45, Normal 45. Set the desired programme and start the selected programme by pressing the Start Button 4. If you do not want to use any of the displayed standard programmes return to the Main Menu by using the button M/OK 2. If you want to cancel the selection of a standard programme in the Main Menu press the button – “Back”.The selected standard programme will be displayed. By pressing the buttons – or + the Main Menu will display the programme “Auto Wash”. Type of Dishes Extra Eco 50 Eco 45 Normal 45 Mixed Dishes Amount of food remnants State of food remnant Little to Many Lightly Adhesive You can find the corresponding programme data (length of time, energy and water consumption) in the short manual. We recommend on principle to use the Auto Programmes because they keep the water and energy consumption as low as possible due to the variable programme run. In the case of the standard programmes on the other hand, the programme run is predetermined.
en 26 Remote Options ** The dishwasher installs itself automatically during the first use within a serve@Home network. In some cases however, it might become necessary to start the enrolment process anew. If the option “Remote Options” is selected, the message “Enrol Device” will be displayed. By pressing the button + 3 you enrol the device again at the gateway. After successfully enrolling the device the message “Auto Wash” will be displayed. If the enrolment is unsuccessful the display shows “no gateway found”. ** Only with installed interface Aqua sensor The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. A light barrier can detect dissolved food remnants in the water, e.g. egg, fat and oats. The Aqua sensor is used according to the programme. When the Aqua sensor is active, ”clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way the water consumption is reduced by approx. 4 litres for utensils which are ”less” dirty. Start programme Before starting check again whether the spray arms can move freely. Press the button “Start” 4 in the Main Menu. The message “Close the door” will be displayed, alternating with a display of the expected programme time. This time is only approximate. The running time indicated at the start of the set programme will probably be required. During the programme run the remaining time will be adjusted according to the water supply temperature and the amount and soil level of the dishes. If you have chosen a time for the programme start the message “Close the door” will appear when the programme is started, alternating with the pre-selected time. Close the door. The programme or the pre-selected time respectively will run. The programme and other settings can still be changed as long as the door is still open after pressing the button “Start” 4 . By pressing the button M/OK 2 “Return”, return to the Main Menu where you can change the settings. Finally start the programme again. When the door is closed after the start and the programme has already started, you will have to interrupt the programme in order to change any settings (see “CancelProgramme”).
en27 Interrupting the programme In order to interrupt the programme, open the door. In order to avoid water escaping, only open the door slightly first. The message “Cancel Programme” will be displayed, alternating with the message “Close the door”, the remaining programme time, the selected programme, and the current programme phase. In order to interrupt, do not in any circumstance press the button – 3 “Cancel Programme” because this will not allow the programme to continue! To continue the programme, close the door. The programme will continue automatically. In the case of a warm water supply or when the appliance is already heated, leave the door slightly ajar for a fewminutes before closing it. Otherwise the door can spring open again due to the warm air trapped in the device’s interior. Terminating the programme Open the door. First open the door only slightly in order to avoid water spraying out. The message “Cancel Programme” will be displayed, alternating with the message “Close the door”, the remaining programme time, the selected programme, and the current programme phase. In order to cancel the programme, press – 3 “Cancel Programme”. “To cancel” and “Close the door” are displayed. Close the door. The water remaining in the device’s interior will be pumped off. Once the pumping off has finished a buzzer will sound 5 times. Open the door. “End” is briefly displayed, the appliance automatically switches off after 5 seconds. End of programme As soon as the programme has finished a buzzer will sound 5 times. Open the door. “End” is briefly displayed, the appliance automatically switches off after 5 seconds. If the door is not opened, an acoustic signal sounds every 10 minutes for one hour. After letting the device cool down take out the dishes. Note For an optimum drying of the dishes wait for 15 minutes after the programme hasfinished before you open the door and empty the dishwasher. During this time the possibly remaining water on the dishes can evaporate and condense on the sides of the device’s interior. Note If the device becomes disconnected from the power supply during operation (e.g. it is switched off or there is a power cut), all settings remain stored. Operation will resume automatically once the power supply has been restored.
en 28 Information on programme sequence When the appliance starts, the following displays are indicated. Prerinse The utensils are washed in this part of the programme without detergent. Finished in X:XX hrs Indicates the remaining running time of the programme. Prerinse Finished in X:XX hrs Wash The utensils are washed optimally with detergent and heated water. Wash Finished in X:XX hrs Final Rinse Rinse aid is automatically added to prevent water stains on the utensils. Final Rinse Finished in X:XX hrs Dry The utensils are being dried. Drying Finished in XX min.
en29 Information on programme sequence Ready The programme has ended. The utensils can now be removed. End Sensors At the start of every programme all sensors (temperature sensor, Aqua sensor, motor sensor) are tested.Sensors working correctly Remaining time is being recalculated The expected programme duration is recalculated according to the quantity and soiling of the utensils. Auto Wash The currently selected programme is displayed. Auto Wash Remaining time is being recalculated
en 30 Information on onboard computer Hygienic washing** When the symbol is displayed, the utensils are hygienically clean. Keep the door closed, otherwise hygienic washing is not guaranteed. Glass protection system** Special gentle treatment of glass; in all programmes. Heat exchanger** Saves energy by recovering heat for the next rinse cycle; in all programmes. Spray pressure** Symbol indicates the different spray pressures in the system. Normal spray active Hygienic washing is active Glass protection system is active Heat exchanger is active ** Is not displayed unless “Onboard computer: on” has been activated under Options / Standard settings