Sharp Xv Z201 Projector User Manual

Introduction
-9
Projector (Rear View)
Using the Terminal Cover
When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied)
to hide the connecting cables.
17
16
62Intake ventilative hole
AC socketIntake ventilative hole
62
18INPUT 2/DIGITAL INPUT
terminal
INPUT 1 COMPONENT
terminals (RCA)
INPUT 4 VIDEO terminal (RCA)
20DIGITAL INPUT
TYPE switch
15INPUT 3 S-VIDEO terminal
 (4-pin Mini DIN)23RS-232C terminal
(9-pin D-sub) 
11Remote control sensor
14...

-10
Part Names
Remote Control (Front View)
Remote Control (Top View)
FREEZE button
32
31
50
52
39
3938
39
31
3131
31
35
47
35
STANDBY button
ENTER button
33KEYSTONE button
UNDO button
INPUT 1 button
INPUT 2 button
INPUT 4 button
AUTO SYNC buttonRESIZE button
PICTURE SETTING button  MENU button30ON button
ADJUSTMENT buttons 
(ƒ/∂/ß/©)
INPUT 3 button
DIGITAL INPUT button
RGB/COMP. button
Remote control signal transmitters
XV_Z201E_E_p04_12.p6503.10.30, 12:16AM 10 

Introduction
-11
Operating the Remote Control

The remote control can be used to control the projector
within the ranges shown in the illustration.
Note
•The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
When using the remote control:
•Be sure not to drop, or expose to moisture or high temperature.
•The remote control may malfunction under a fluorescent lamp.
Under that circumstance,...

-12
Accessories
Remote control
Power cord
(For U.K., Hong Kong
and Singapore)
21 pin RCA
conversion adaptor
(Supplied for Europe only)
Lens cap Video cable Two AA size batteries
(For Australia
and New Zealand)
Projector Operation manual
Screws for terminal cover(For Europe except U.K.)
Note
•Depending on the region, projectors are shipped with only
one power cord (see above). Use the power cord that cor-
responds to the wall outlet in your country.
3 RCA to 15-pin D-sub cable (3.0 m) AN-C3CP
DVI to...

Connections and Setup
Connections and Setup
XV_Z201E_E_p13_24.p6503.10.30, 12:17AM 13 

-14
Connecting the Projector to Other Devices
Before Connecting
Note
•Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off
the devices to be connected. After making all connections, turn on the projector and then the other
devices.
When connecting a computer, be sure that it is the last device to be turned on after all the connec-
tions are made.
•Be sure to read the operation manuals of the devices to be connected before making connections.
This projector...

Connections and Setup
-15
Connecting to Video Equipment
Connecting to Video
Equipment Using an
S-video Cable (INPUT 3)
Using an S-video cable, a VCR, DVD player or
other video equipment can be connected to
INPUT 3 input terminal.
1Connect an S-video cable to
the projector.
2Connect the S-video cable to
the video equipment.
Note
•The INPUT 3 (S-VIDEO) terminal uses a
video signal system in which the picture
is separated into color and luminance sig-
nals to realize a higher-quality image. To
view a...

Connecting to Video
Equipment Using a
Composite Video Cable
(INPUT 4)
Using a composite video cable, a VCR, DVD
player or other video equipment can be con-
nected to INPUT 4 input terminal.
1Connect a composite video
cable to the projector.
2Connect the composite video
cable to the video equipment.
To INPUT 4 terminal
VCR or other video equipment
To video output terminal Composite video cable
-16
Connecting the Projector to Other Devices
XV_Z201E_E_p13_24.p6503.10.30, 12:17AM 16 

Connections and Setup
-17
Connecting to
Component Video
Equipment Using a
Component Cable
(INPUT 1)
Use a component cable when connecting com-
ponent video equipment such as DVD players
and DTV decoders to INPUT 1 terminals.
1Connect a component cable to
the projector.
2Connect the above cable to the
component video equipment.
Note
•Make sure to turn both the projector and
the video equipment off before connect-
ing.
Connecting to a DVD Player and DTV Decoder
To analog component
output terminal To INPUT...

Connecting to Compo-
nent Video Equipment
Using a 3 RCA to 15-pin
D-sub Cable and the
DVI to 15-pin D-sub
Adaptor (INPUT 2)
Use a 3 RCA to 15-pin D-sub cable and the
DVI to 15-pin D-sub adaptor when connecting
component video equipment such as DVD
players and DTV decoders to INPUT 2 termi-
nal.
1Connect a DVI to 15-pin D-sub
adaptor to the projector.
2Connect a 3 RCA to 15-pin D-
sub cable to the above adaptor.
•Secure the connectors by tightening the
thumbscrews.
3Connect the above cable to the
video...