Sharp Xv Z201 Projector User Manual

XV-Z201E
Printed on 100% post-consumer recycled paper.
Gedruckt auf 100% wiederverwertungs Papier.
Imprimé sur 100% de papier recyclé.
Utskrift på återvunnet papper av 100% återvunnet material.
Impreso en 100% de papel reciclado de postconsumo.
Stampato su carta riciclata al 100%.
Gedrukt op 100% kringlooppapier.
ENGLISH .............
-1 –
-70
DEUTSCH ............
-1 –
-70
FRANÇAIS ...........
-1 –
-70
SVENSKA ............
-1 –
-70
ESPAÑOL ............
-1 –
-70
ITALIANO .............
-1 –
-70
NEDERLANDS...

SPECIAL NOTE FOR USERS IN THE U.K.The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse.
Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked  or ASA and of
the same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible...

Introduction
-1
Before using the projector, please read this operation manual carefully.
WARNING:Intense light source. Do not look into the beam or view it directly. Be especially careful that children
do not look directly into the beam.
WARNING:To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
CAUTION:
To reduce the risk of electric shock, do not remove cabinet. No user-serviceable parts are inside.
Refer servicing to qualified service personnel....

-2
WARNING:
Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments.
Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile
the contents thereof.
LAMP REPLACEMENT 
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW  1 HOUR TO COOL BEFORE
REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP
UNIT TYPE BQC-XVZ200++1 ONLY. UV RADIATION : CAN CAUSE
EYE DAMAGE. TURN OFF LAMP...

Introduction
-3
Contents
Introduction
Contents ............................................................... 3
IMPORTANT SAFEGUARDS ............................... 4
Quick Guide ......................................................... 7
Part Names .......................................................... 8
Operating the Remote Control ......................... 11
Accessories ....................................................... 12
Connections & Setup
Connecting the Projector to Other Devices .......

-41. Unplug the Projector from the wall outlet before
cleaning.
2. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
3. Do not use attachments not recommended by
the Projector manufacturer, as they may cause
hazards.
4. Do not use the Projector near water; for example,
near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, near a swimming pool,
etc. Never spill liquid into the projector.
5. Do not place the Projector on an unstable cart,
stand, or table. The...

Introduction
-5 19. This Projector is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type mains plug.
b. Three-wire grounding type mains plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
•Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
•Microsoft and Windows are...

-6
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up
your projector.
Caution concerning the lamp unit

There is a potential hazard of glass
particles if the lamp ruptures. In case
of lamp rupture, contact your near-
est Sharp Authorised Projector
Dealer or Service Centre for replace-
ment.
See “Replacing the Lamp” on page 59.
Cautions concerning the setup of the projector

For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be...

Introduction
-7
The power indicator
illuminates green.
In this page, connection of the projector and the video equipment is explained as an example
for the procedure from setup to projection. Refer to each page for details.
Quick Guide
Required equipments
Video cable
Projector Power cord
1. Place the projector facing a wall or a screen.
2. Connect to video equipment. (Page 16)6. Turn the projector on using  on the remote
control. (Page 30)
3. Connect the output terminal of the video equip-
ment to the...

-8
Projector (Front and Top View)
30
58
58
POWER indicator
6Exhaust ventilative hole LAMP indicator TEMPERATURE 
WARNING indicator
39ADJUSTMENT buttons
(ƒ/∂/ß/©) 
39UNDO button
38MENU button
35RESIZE button
31INPUT button
24Swivel Stand 
LOCK/UNLOCK lever
11Remote control sensor
Lens cap
Zoom knob25
Exhaust ventilative hole6
Focus ring25
25Lens shift dial
39ENTER button
33KEYSTONE button
ON button30
STANDBY 
button32
47PICTURE SETTING button
Attaching the Lens Cap
The lens cap can be attached to the...