Sharp Xv Z10e Projector User Manual

-29
Basic Operation
', ", \, |buttons KEYSTONE
button
UNDO
button
', ", \, | buttons
UNDO button
Correcting Trapezoidal
Distortion
When the image is projected either from the top or
from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
Note
•The Keystone Correction can be adjusted up
to an angle of approximately ±30 degrees and
the screen can also be set up to an angle...

-30
Image Projection
Adjusting the Lens
The image is focused and adjusted to the de-
sired size using the focus ring or zoom knob
on the projector.
1Adjust the focus by rotating the
focus ring.
2Adjust zooming by moving the
zoom knob.
Focus ring Zoom knob
Zoom in
Zoom out
XV_Z10E_E_p26_35.p6503.11.7, 4:15 PM 30 

-31
Basic Operation
Using the Adjustment
Feet
The height of the projector can be adjusted us-
ing the adjustment feet at the front and rear of
the projector when the screen is not perpen-
dicular to the lens centre of the projector, or
when installation surface is slightly slanted.
When the screen is in a higher position than
the projector, the projection image can be made
higher by adjusting the projector.
1Press the HEIGHT ADJUST button.
•The front adjustment foot comes out.
2Lift the projector to...

-32
Image Projection
In addition to the zoom function and adjustment of projection angle using the adjustment foot, it is possible
to move the lens up and down and left and right (360
°) to adjust the projection position simply by moving
the lens shift lever on the front of the projector. This is a useful function in cases such as when the screen
cannot be moved.
Adjustable range
Adjustable range
Adjustable rangeAdjustable range
Zooming axis
Adjustable range of 
the image centre
Image centre
Width of the...

-33
Basic Operation
FREEZE button
Freezing a Moving
Image
1Press .
•The projected image is frozen.
2Press  again to return to the
moving image from the currently
connected device.
Freeze Image
You can instantly freeze a moving image with
the remote control.
Adjusting the Projected
Image Position
Adjust the projected image position
using the lens shift lever.
Info
•When using the projector (during projection),
be sure not to subject the projector to any
impact. If the projector is subjected to impact,
the...

-34
Selecting the Picture Display Mode
This function allows you to modify or customise the picture display mode to enhance
the input image. Depending on the input signal, you can choose “STRETCH”, “SIDE
BAR” or “CINEMA ZOOM” image.
Switching the Picture
Display Using Different
Input Signals
Press .
•Pressing  changes the picture display mode
as shown on page 35.
•To return to the standard image (“STRETCH”),
press 
 while “RESIZE” is displayed on the
screen.
•You can also change the picture display mode...

-35
Basic Operation
: Cutout area on which images cannot be projected.
480I
480P
NTSC
PAL
SECAM
1080I
VGA
SVGA
XGA
Input SignalSIDE BAROutput screen imageSTRETCH(Default setting)CINEMA ZOOM
4:3 aspect ratio
Letter box
16:9 aspect ratio
4:3 aspect ratio Squeezed
720P
Note
• “STRETCH” is fixed when 720P or 1080I signals are entered.
XV_Z10E_E_p26_35.p6503.11.7, 4:16 PM 35 

-36
The menu screens allow you to adjust the image and various projector settings. (The menu items differ
depending on the input mode.)
The menu can be operated with the projector or with the remote control.
Using the Menu Screen
Menu Selections
(Adjustments)
1Press .
Note
•The “Picture” menu screen for the se-
lected input mode is displayed.
', ", \, |
buttonsMENU button UNDO
button ENTER 
button
ENTER button
MENU button
', ", \, | buttons
XV_Z10E_E_p36_41.p6503.11.7, 4:17 PM 36 

Adjustments and Settings
-37
2Press 
\ \\ \
\ or 
| || |
| to select the menu
screen (icon) you want to set.
•The menu icon for the selected menu
screen is highlighted.
Note
•The “Fine Sync” menu is not available
for INPUT 2 or 3.
•For items on the menus, see the tree
charts on pages 40 and 41.
3Press 
' '' '
' or 
" "" "
" to select the item
you want to adjust.
•The selected item is highlighted.
Note
•If you want to adjust the item while view-
ing the projected...

-38
Using the Menu Screen
Menu Selections
(Settings)
1Press .
Note
•The “Picture” menu screen for the se-
lected input mode is displayed.
2Press 
\ \\ \
\ or 
| || |
| to select the menu
screen (icon) you want to set.
•The menu icon for the selected menu
screen is highlighted.
Note
•The “Fine Sync” menu is not available
for INPUT 2 or 3.
•For items on the menus, see the tree
charts on pages 40 and 41.
', ", \, |
buttonsMENU button UNDO
button ENTER 
button
ENTER button
MENU button
', ",...