Sharp Xv Z10000e Projector User Manual

Appendix
-79
Connecting Pin Assignments
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
Pin No. Signal Name I/O Reference
1 Not connected
2 RD Receive Data Input Connected to internal circuit
3 SD Send Data Output Connected to internal circuit
4 Reserved Connected to internal circuit
5 SG Signal Ground Connected to internal circuit
6 Reserved Connected to internal circuit
7 Reserved Connected to internal circuit
8 Reserved Connected to internal circuit
9 Not connected
DVI-I (INPUT...

-80
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 23 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate*: 9,600 bps / 38,400bps / 115,200bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
*Use the same settings for the projector and computer....

Appendix
-81
CONTROL CONTENTSCOMMANDPARAMETERRETURNCONTROL CONTENTSCOMMANDPARAMETERRETURNPPKVIIIIIIARRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR
RRRRRRRRRRRRRRRRRVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVGGGGGGGGGGGGGGGG
OOESRRVVRCDAAAABBBBBBBBAAAACCCCAAAAAAAAAAAAAAAABBBBBBBBBBBBBBBBCCCCCCCC
CCCCCCCCAAABBBCCCBBBBBBBBBBBBBBBBAAAAAAAAAAAAAAAABBBAAAMMMMMMMMMMMMMMMM
WWYIGGEEGHJSSSSSSSSSSSSSSSSSSSSPBCTSCRRWWPPPPPPPBCTSCRRWWPPPPPPPBCTSCRR...

-82
Note
•If an underbar (_)  appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value
in the range indicated in brackets under CONTROL CONTENTS.
•*
1 FINE SYNC can only be set in the displayed RGB mode.
The return value of “TLTT___1” becomes “0” when the projector is in the following states:
•Power is in the standby mode•Cooling fan is operating after the power has been turned off
CONTROL CONTENTSCOMMANDPARAMETERRETURNCONTROL...

Appendix
-83
CONTROL
 ITEMSYSTEM CODE
C1
1
1
1
1
1
1
1
1
1
1ON
OFF
MENU
∂
ƒ
ß
©
ENTER
UNDO
RGB/COMP.0
0
0
0
0
0
0
0
0
0
C2
1
1
1
1
1
1
1
1
1
1
C3
1
1
1
1
1
1
1
1
1
1
C4
0
0
0
0
0
0
0
0
0
0
C5 C6
0
0
0
0
1
0
1
1
1
11
1
0
0
0
0
1
1
0
0
C7
1
1
1
1
1
0
1
1
0
0
C8
0
0
0
1
1
0
1
0
1
0
C9
1
1
0
1
1
1
0
1
1
1
C10 C11
0
0
0
0
0
0
0
0
0
11
0
1
0
0
1
1
1
1
1
C12
0
1
1
1
1
0
0
0
0
1
C13
1
1
1
1
1
1
1
1
1
1
C14
0
0
0
0
0
0
0
0
0
0
C15
DATA CODEJUDGEMENT
CODEJUDGEMENT
CODECONTROL
 ITEMSYSTEM CODE
C1
1
1
1
1
1
1
1
1...

-84
Computer Compatibility Chart
Note
•This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off
the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can
be found in your notebook computer’s operation manual.
•When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
•When projecting moving image of interlace signals...

Appendix
-85
Troubleshooting
Check Page
•Projector power cord is not plugged into the wall outlet. 16
•Power to the external connected devices is off. –
•The selected input mode is wrong. 33
•Cables incorrectly connected to rear panel of the projector. 17-22
•Remote control batteries have run out. 13
•External output has not been set when connecting notebook computer.–
•The cover of the lamp unit is not installed correctly. 78
• The selected “Signal Type” is wrong. 65
• The video signal format of the...

-86
CheckProblemPage
Troubleshooting
For SHARP Assistance (U.S.A only)
If you encounter any problems during setup or operation of this projector, first refer to the “Trouble-
shooting” section on pages 85 and 86. If this operation manual does not answer your question,
please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance.
 Or, send us an e-
mail at [email protected] .
Our World Wide Web address is http://www.sharpusa.com/ .
•Change the input signal type setting. 65
•The lamp...

Appendix
-87
Specifications
Projector
XV-Z10000
NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM
DTV480I/DTV480P/DTV720P/DTV1080I
DLP chip, RGB optical shutter method
Panel size: 0.8
Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Drive method: Digital Light Processing (DLP™)
No. of dots: 921,600 dots (1,280 [H] × 720 [V])
1–1.35 × zoom lens, F3.8, f = 32.5–44.0 mm
270 W SHP lamp
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω...

-88
Dimensions
15 
49/50 (406)
7 (178)
18 11/16 (475)
Side ViewSide ViewTop View
Rear View
Front View
Bottom View
Units: inches (mm)