Sharp Xg Nv7xu Projector User Manual
Have a look at the manual Sharp Xg Nv7xu Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
E-20 Operation Reversed Image Setup Rear projection •Place a translucent screen between the projector and the audience. •Use the projector’s menu system to reverse the projected image. (See page 43 for use of this function.) Projection using a mirror •Place a mirror (normal flat type) in front of the lens. •Use the projector’s menu system to reverse the projected image. (See page 43 for use of this function.) •The image reflected from the mirror is projected onto the screen. •Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. CAUTION •When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of the audience. Setting up the Screen •It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. •Before mounting the projector, contact your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center to obtain the recommended ceiling- mount bracket (sold separately). (AN-NV7T ceiling- mount bracket, AN-TK201/202 extension tube for AN- NV7T.) •When the projector is in the inverted position, use the upper edge of the screen as the base line. •Use the projector’s menu system to select the appropriate projection mode. (See page 43 for use of this function.) Ceiling-mount Setup
E-21 Operation 13 (4 m) 30˚ 30˚ 120˚ MOUSEADJ. MOUSE/ADJUSTMENT switch (Remote control) MOUSEADJ. Controlling the Projector Using the Wireless Mouse Remote mouse receiver Remote control Using the Remote Control as a Wireless Mouse Remote Control/Mouse Receiver Positioning The remote control has the following three functions: •Projector control •Wireless mouse •Laser pointer •The remote control can be used to control the projector within the ranges shown below. •The remote mouse receiver can be used with the remote control to control the mouse functions of a connected computer within the ranges shown below. •The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material.Wireless mouse Laser pointerProjector control Operating the Wireless Mouse from the Remote Control 30˚45˚ 23 (7 m)30˚ 30˚ 45˚ Remote control Remote control
E-22 Operation 2 Be sure the supplied remote mouse receiver is connected to your computer. Slide the MOUSE/ADJUSTMENT switch to MOUSE. Effective buttons in MOUSE mode Use as a Wireless Mouse 1 MOUSEADJ. Use as a Laser pointer Slide the MOUSE/ADJUSTMENT switch to MOUSE. Press LASER POINTER ( ) to activate the laser pointer. When the button is released, the light automatically goes off. •For safety, the laser pointer automatically goes off after 1 minute of continuous use. To turn it on, release LASER POINTER ( ) and press again. MOUSEADJ. 1 •The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer’s operation manual for details of setting up/installing the mouse driver. •For one-button mouse systems, use either the LEFT-CLICK or RIGHT-CLICK button. Using the remote control in a dark room Press BACKLIGHT, and the buttons will light up. Green lights refer to mouse operations, and red lights to projector adjustments. Position of MOUSE/ADJUSTMENT switch ON (RED) MOUSE LASER POINTER (GREEN) BLACK SCREEN (GREEN) RIGHT-CLICK (GREEN) MOUSE (NOT LIT) LEFT-CLICK (NOT LIT) ADJ. MENU (RED) KEYSTONE (RED) ENTER (RED) ADJUSTMENT (NOT LIT) UNDO (NOT LIT) Button name LASER POINTER/MENU BLACK SCREEN/KEYSTONE RIGHT-CLICK/ENTER MOUSE/ADJUSTMENT LEFT-CLICK/UNDO POWER ON/OFF VOLUME / MUTE Position of MOUSE/ADJUSTMENT switch ON (RED) MOUSE ADJ. Button name INPUT IrCOM FREEZE AUTO SYNC ENLARGE RESIZE TOOLS GAMMA LEFT-CLICK RIGHT-CLICK MOUSE BLACK SCREENLASER POINTER Operating the Wireless Mouse from the Remote Control
E-23 Operation Using the GUI (Graphical User Interface) Menu Screens This projector has two sets of menu screens (INPUT/VIDEO) that allow you to adjust the image and various projector settings. These menu screens can be operated from the projector or the remote control with the following buttons. (GUI) On-screen Display 1 INPUT (COMPUTER/RGB) mode 1 VIDEO mode 4(Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position.) 1Press MENU to display the INPUT or VIDEO mode menu bar. 2Press ß/© to select an adjustment menu on the menu bar. 3Press ∂/ƒ to select a specific adjustment item. 4To display a single adjustment item, press ENTER after selecting the item. Only the menu bar and the selected adjustment item will appear. 5Press ß/© to adjust the item. 6Press UNDO to return to the previous screen. 7Press MENU to exit from the GUI. •For details on items on the menu screen, see the tree charts on the next page. ß 2 © ß 2 © ß 2 © ß 5 © MOUSEADJ. ∂ 3ƒ∂3ƒ ß 5 © ß 5 © 46 2, 3, 5 1, 7 Projector Remote control
E-24 Operation Items on the INPUT1 or INPUT2 Mode Menu Bar Using the GUI (Graphical User Interface) Menu Screens Items on the VIDEO Mode Menu Bar Main menuSub menu Main menuSub menu Contrast Picture Audio30 30 I/P Conversion Options Video System Language English PRJ Mode StatusCeilingFront CeilingRear Deutsch Español Nederlands Français Italiano Svenska Português Front Rear Background Startup ImageInterlaced Progressive Auto PAL (50 /60Hz) SECAM NTSC4.43 NTSC3.58 Sharp Custom Blue None Auto Power Off Sharp Custom None Lamp Timer BLK SCRN Disp OSD Display [ON/OFF] [ON/OFF] [ON/OFF] Bright30 30 Color30 30 Tint30 30 Sharp30 30 Red30 30 Blue30 30 Treble30 30 Bass30 30 Reset Reset 1152864 1024864 1152882 1152870 Tint Auto Sync Fine Sync Audio30 30 Color30 30 Clock150 150 150 150 Bass Options Lamp Timer Language English PRJ Mode StatusCeilingFront CeilingRear Deutsch Español Nederlands Français Italiano Svenska Português Front Rear Auto Sync Disp BLK SCRN Disp OSD Display [ON/OFF] [ON/OFF] [ON/OFF] [ON/OFF] [ON/OFF] Signal Type Background Sharp Startup Image Signal Info Sharp Custom Custom I/P ConversionInterlaced Progressive Blue None Computer/RGB Component None 30 30 Treble30 30 Reset Phase60 60 H-Pos V-Pos Reset Save Setting Select Setting1 2 • • 7 Resolution800600 640480Vert Freq 75 Hz 72 Hz Special Modes60 60 Sharp30 30 Contrast Picture30 30 Bright30 30 Red30 30 Blue Reset30 301 2 • • 7 Resolution800600 640480Vert Freq 75 Hz 72 Hz Resolution Hor Freq Vert Freq640480 37.5 kHz 72 Hz Auto Power Off •The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only. •“Color”, “Tint”, and “Sharp” appear only when Component input is selected in INPUT 1 mode. •Only the items highlighted in the tree charts above can be adjusted. •To adjust the items under the sub menu, press © after selecting the sub menu. •The signal is set to COMPUTER/RGB, when inputting DIGITAL signal. •The items displayed in gray cannot be adjusted.
E-25 Operation The IrCOM function can transfer still images from a computer or digital camera to the projector via infrared (wireless) communication. Sharp Advanced Presentation Software •This function requires the supplied Sharp Advanced Presentation Software (SAPS). •Install the SAPS in the supplied CD-ROM on the computer. •See the operation manual of the software for installation and operating instructions. •Position the projector and the IrCOM transmitting device within the range shown on the left. •To avoid transmission errors or changes in the image, ensure the following when setting up the projector and transmitting device. •The IrCOM sensors on both the projector and transmitting device are protected from direct sunlight or strong ambient light. •The transmitting device has sufficient battery power. •The projector and transmitting device are positioned within the designated operating range. •The IrCOM sensors on the projector and transmitting device are correctly aligned. •The distance between the projector and transmitting device may have to be less than 4 (10 cm) depending on the transmitting device. •When using the digital still camera, set it to the image transmission mode. •Align the projector and transmitting device at the same height and angle at a distance of 4 (10 cm) to 3 3 (1 meter) with an unobstructed line of view. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position.) 1Press IrCOM to enter the IrCOM mode. 2And then the On-screen Display changes as shown on the left. •If the On-screen Display does not change as shown on the left, the projector may not be within the reception range from the IrCOM transmitting device. 3Press INPUT to exit the IrCOM mode. Using IrCOM for Wireless Presentations Projector 3 1, 2 Remote control 15˚ 15˚4 (10 cm)–3 3 (1 m) 15˚ 15˚ PC Digital camera f ff f f f ff f f On-screen Display MOUSEADJ.
E-26 Operation Selecting the On-screen Display Language 4 2, 3 1, 5 Projector (GUI) On-screen Display English is the preset language for the On-screen Display. It can be changed to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position.) 1Press MENU. 2Press ß/© to select “Language”. 3Press ∂/ƒ to select the desired language . 4Press ENTER to save the setting. The On-screen Display is now programed to display in the language selected. 5To exit from the GUI, press MENU. Selecting the Video Input System Mode (VIDEO mode only) 5 2, 3, 4 1, 6 Projector The video input system mode is preset to “Auto”; however, it can be changed to a specific system mode, if the selected system mode is not compatible with the connected audiovisual equipment. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position.) 1Press MENU. 2Press ß/© to select “Options”. 3Press ∂/ƒ to select “Video System”, and then press ©. 4Press ∂/ƒ to select the desired video system mode. 5Press ENTER to save the setting. 6To exit from the GUI, press MENU. •When the system mode is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system you are viewing. (GUI) On-screen Display MOUSEADJ. MOUSEADJ. Remote control Remote control
E-27 Operation 2, 3 1, 4 Picture Adjustments You can adjust the projector’s picture to your prefer- ences with the following picture settings. Description of Adjustment Items Projector For less contrast For less brightness For less color intensity Skin tones become purplish For less sharpness For weaker red For weaker blue Selected itemFor more contrast For more brightness For more color intensity Skin tones become greenish For more sharpness For stronger red For stronger blue ß button © button All image adjustment items are returned to the factory preset settings. Contrast Bright Color Tint Sharp Red Blue Reset (GUI) On-screen Display (COMPUTER/RGB input in INPUT mode) 1 2 •“Color”, “Tint” and “Sharp” do not appear for COMPUTER/ RGB input in INPUT 1 mode. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position.) 1Press MENU. Menu bar and “Picture” menu screen appear. GUI operation guide is also displayed. 2Press ∂/ƒ to select a specific adjustment item. 3Press ß/© to move the mark of the selected adjustment item to the desired setting. 4To exit from the GUI, press MENU. •To reset all adjustment items, select “Reset” on the “Picture” menu screen and press ENTER. •The adjustments can be stored separately in the “INPUT 1”, “INPUT 2” and “VIDEO” modes. •For COMPONENT input in INPUT 1 mode, “Sharp” is adjustable only when a DVD player is connected. •When adjusting the items under the “Picture” menu in DIGITAL input, the changes affect both the picture being viewed and the GUI menu screen. MOUSEADJ. Remote control
E-28 Operation This projector’s audio is factory preset to standard settings. However, you can adjust it to suit your own preferences by adjusting the following audio settings. (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position.) 1Press MENU. Menu bar and “Picture” menu screen appear. GUI operation guide is also displayed. 2Press ß/© to select “Audio”. 3Press ∂/ƒ to select a specific adjustment item. 4Press ß/© to move the mark of the selected adjustment item to the desired setting. 5To exit from the GUI, press MENU. •To reset all adjustment items, select “Reset” on the “Audio” menu screen and press ENTER. Description of Adjustment Items 2, 3, 4 1, 5 Projector © button ß button Selected item 2 3(GUI) On-screen Display Audio Adjustments For weaker treble For weaker bassTreble Bass ResetFor stronger treble For stronger bass All audio adjustment items are returned to the factory preset settings. MOUSEADJ. Remote control
E-29 Operation Computer Image Adjustments When displaying computer patterns which are very detailed (tiling, vertical stripes, etc.), interference may occur, causing flickering, vertical stripes, or contrast irregularities in portions of the screen. Should this occur, adjust “Clock”, “Phase”, “H-Pos” and “V-Pos” for optimum computer image. •Computer image adjustment can be made easily by pressing AUTO SYNC (). See the next page for details. (GUI) On-Screen Display 2, 3, 4 1, 5 Projector Clock Phase H-Pos V-Pos Description of Adjustment Items (Select the desired computer input mode with INPUT.) (Slide the MOUSE/ADJUSTMENT switch on the remote control to the ADJ. position.) 1Press MENU. Menu bar and “Picture” menu screen appear. GUI operation guide is also displayed. 2Press ß/© to select “Fine Sync”. 3Press ∂/ƒ to select a specific adjustment item. 4Press ß/© to move the mark of the selected adjustment item to the desired setting. 5To exit from the GUI, press MENU. •To reset all adjustment items, select “Reset” on the “Fine Sync” menu screen and press ENTER. •When inputting DIGITAL signal, the projector automatically selects the settings for the best possible picture. You do not need to adjust any settings. 2 3 Description Selected item MOUSEADJ. Remote control Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centers the on-screen image by moving it to the left or right. Centers the on-screen image by moving it up or down.