Sharp Xg Mb67x Projector Quickstart Guide

-21
View Setting Detail List
([V]View All Setting)
1
1 1
1
1 Enter “v” and press the “Enter” key.
Display all setting values(*).
Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the
details to be set. Setting is carried out one item at a time, and saved at the end.
▼SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name...

-22
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.1
1 1
1
1 Enter “s” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be...

-23
IP Address Setting
([1]IP Address)
Setting of IP address.1
1 1
1
1 Enter “1” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
1
1 1
1
1 Enter “2” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic pro\
cedure,...

-24
Password Setting
([5]Password)
Carrying out security protection using password.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter password and press the “Enter” key.
Display set password (*).
Note
•Password can be up to 8 characters.
• You can input the  characters below :
a-z, A-Z, 0-9, -, _
• In the def ault state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
1
1 1
1
1 Enter “6” and press the “Enter” key.
2
2 2...

-25
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.1
1 1
1
1 Enter “d” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•If Disconnect All is performed, the connection to
the projector  via network  will be forcibly...

-26
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
•If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is  entered.
• If there is a...

-27
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.1
1 1
1
1 Enter “0” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Nor mally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
1
1 1
1
1 Enter “!” and press the “Enter”...

-28
Communication cannot be established with the projector
When connecting the projector using serial-connection
\Check that the RS-232C terminal of the projector and a computer or the commercially
available controller are connected correctly.
\ Check that the RS-232C cable is a cross-over cable.
\ Check that the RS-232C port setting for the projector corresponds to the setting for the
computer or the commercially available controller.
When connecting the projector to a computer using network (LAN)-...

-29
Troubleshooting
\ Take the following steps for checking the network settings for the computer.
1. Open a command prompt (MS-DOS Prompt). •In the case of Windows
® 98 or 98SE: click “START”  ➔ “Programs”  ➔ “MS-DOS Prompt” in
order.
• In the case of Windows
® Me: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “MS-DOS
Prompt” in order.
• In the case of Windows
® 2000: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “Command
Prompt” in order.
• In the case of Windows
® XP: click “START”  ➔ “All...

-30
\Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check
if an IP address is set.
1. Open a command prompt (MS-DOS Prompt).
•In the case of Windows
® 98 or 98SE: click “START”  ➔ “Programs”  ➔ “MS-DOS Prompt” in
order.
• In the case of Windows
® Me: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “MS-DOS
Prompt” in order.
• In the case of Windows
® 2000: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “Command
Prompt” in order.
• In the case of Windows
® XP: click...