Sharp Xg Mb67x Projector Quickstart Guide

-11
Setting up the Projector Network Environment
3. Setting up a NetworkConnection for the
Projector
Settings for such items as the projector’s IP
address and subnet mask are compatible with
the existing network.
Set each item on the projector as follows. (See
page 50 of the projector’s operation manual
for setting.)
DHCP Client : Off
IP Address : 192.168.150.002
Subnet Mask : 255.255.255.000
1Start Internet Explorer (version
5.0 or later) on the computer, and
enter “http://192.168.150.2/”  in
“Address”,...

-12
4The TCP/IP setting screen ap-
pears, ready for network settings
for the projector.
Note
• Confirm the existing network’s segment (IP
address group) to avoid setting an IP ad-
dress that duplicates the IP addresses of
other network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”,
you don’t have to change the projector IP
address.
• For details about each setting, consult your
network administrator.
5Click the “Apply” button.
6The set...

-13
Controlling the Projector via LAN
Controlling the Projector
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external equipment
before starting the operation. (See pages 21-
27 of the projector’s operation manual.)
Complete the AC cord connection. (See page
27 of the projector’s operation manual.)
Note
•When connecting the projector to the LAN, use
a LAN cable (Category 5).  When connecting the
projector to a hub, use a straight-through cable.
1Start Internet Explorer (version...

-14
Confirming the Projector
Status (Status)
On this screen, you can confirm the projector
status. You can confirm the following items :
•
• •
•
•MAC Address
•
• •
•
•Power
•
• •
•
•Condition
•
• •
•
•Lamp Timer
•
• •
•
•Lamp Life
•
• •
•
•Input
•
• •
•
•Signal Info
•
• •
•
•S erial Number
Note
•If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be dis-
played. Wait for a moment and then oper-
ate again.
• For details about each item,...

-15
Controlling the Projector via LAN
Setting and Adjusting the
Projector (Settings & Adjustments)
Example: “Picture” screen display for INPUT 1
On these screens, you can make projector
settings or adjustments. You can set or adjust
the following items :
•
• •
•
•Picture Mode
•
• •
•
•CLR Temp
•
• •
•
•Bright Boost
•
• •
•
•Progressive  (INPUT 3/4)
•
• •
•
•Lamp Setting
•
• •
•
•Resolution Setting
•
• •
•
•Signal Type  (INPUT  1/2)
•
• •
•
•Video System (INPUT 3/4)
•
• •
•
•Resize
•
• •
•
•A uto Keystone...

-16
Controlling the Projector via LAN
Making General Settings
for the Network 
(Network -
General)
On this screen, you can make general settings
relating to the network.
After clicking the “Apply” button, the set val-
ues appear. Confirm that the values are set
properly, and then click the “Confirm” but-
ton.
Note
•After setting items, wait for 10 seconds and
then re-access.
• Projector Name can be up to 12 characters.
• You can input the  characters below :
A-Z, 0-9, -, _, (,), space
( When “a-z” are...

-17
Controlling the Projector via LAN
Setting  Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
(Mail – Recipient Settings)
On this screen, you can input e-mail destina-
tions to which error  notification (error items)
e-mails are sent.
Note
• E-mail Address can be up to 64 characters.
• You can input the  characters below :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |,
},  ~
, _, ’, ., @, `
(You can input “@” only one time.)
• For details about error...

-18
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
RS-232C
1Launch general purpose terminal
emulator.
2Input settings for the RS-232C port
of the terminal emulator as follows.
Baud Rate : 9600 bps*
Data Length : 8 bit
Parity Bit : None
Stop Bit : 1 bit
Flow Control : None
* This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
3Input “PJS11234” and press the
“Enter”...

-19
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
Telnet
1Click “Start” from the Windows® desk-
top and select “Run”.
2Enter “telnet 192.168.150.2” in the text
box that opens up. (If the IP address
of the projector is 192.168.150.2.)
3Click  the “OK”  button.
4“User Name:” is displayed. Input the
user name and press the “Enter”
key.
•If a user name has not yet been set, just
press the “Enter” key.
5“Password:” is displayed. Input the
password and press the “Enter” key.
•If a...

-20
Setting up the Projector Using RS-232C or Telnet
SETUP MENU (Main Menu)
[1]IP Address
IP address settings. (Page 
23 )
[2] Subnet Mask
Subnet mask settings. (Page 
23 )
[3] Default Gateway Default gateway settings. (Page 
23 )
[4] User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page 
23 )
[5] Password (Factory default setting : Not Required)
Setting of password for security protection. (Page 
24 )
[6] RS-232C Baud Rate (Factory default setting :...