Sharp Xg Mb67x Projector Quickstart Guide

							-21
View Setting Detail List
([V]View All Setting)
1
1 1
1
1 Enter “v” and press the “Enter” key.
Display all setting values(*).
Enter number or symbol of item to be selected on the SETUP MENU. When setting, input the
details to be set. Setting is carried out one item at a time, and saved at the end.
▼SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XG-MB67X
Projector Name : XG-MB67X
MAC Address : 08:00:1F:B1:B7:74
DHCP Client : Enabled
IP Address : 192.168.150.2
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232 Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
A uto Logout Time : 5 minutes
Search Port : 5006
1
*
Set Items
Example: When setting IP Address (change from
192.168.150.2 to 192.168.150.3)
1
1 1
1
1 Enter “1” (number of item to be set), and press
the “Enter”  key.
Display current IP address (*1).
2
2 2
2
2 Enter IP address to be set and press the “En-
ter” key.
Display IP address after change (*2).
3
3 3
3
3 Enter “v” and press the “Enter” key to verify
setting detail list.
IP address is being changed (*3).
Note
•Ve rification of setting detail list can be omitted.
• Setting details are not effective until they have
been saved. (Page 
22 )
• If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>1
IP Address : 192.168.150.2
Please Enter : 192.168.150.3
(change) —> 192.168.150.3
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>v
Model Name : XG-MB67X
Projector Name : XG-MB67X
MAC Address : 08:00:1F:B1:B7:74
IP Address : 192.168.150.3
Subnet Mask : 255.255.255.0
Default Gateway : Not Used
RS-232C Baud Rate : 9600 bps
Password : Not Required
**********(Advanced Status)**********
Data Port : 10002
Accept IP Address : Accept All
A uto Logout Time : 5 minutes
Search Port : 5006
1
2
3 *1
*2
*3
Setting up the Projector Using RS-232C or Telnet 
						

							-22
Save Settings and Quit
([S]Save & Quit)
Save set values and quit menu.1
1 1
1
1 Enter “s” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>s
All Connection will be disconnect.
Continue(y/n)? y
Apply New setting...Done.
1
2
Quit without Saving Set-
tings ([Q]Quit Unchanged)
Quit menu without saving setting values.
1
1 1
1
1 Enter “q” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
▼
SETUP MENU
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name
[8]DHCP Client[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>q
Quit Without Saving(y/n)? y
Setting Unchanged.
1
2
Setting up the Projector Using RS-232C or Telnet 
						

							-23
IP Address Setting
([1]IP Address)
Setting of IP address.1
1 1
1
1 Enter “1” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display IP address after change (*).
Subnet Mask Setting
([2]Subnet Mask)
Setting subnet mask.
1
1 1
1
1 Enter “2” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display subnet mask after change (*).
The setting procedure for each item will be explained. For the basic pro\
cedure, please refer
to “Set Items” on page 
21 .
setup>1
IP Address :192.168.150.2
Please Enter :192.168.150.3
(change)      —>  192.168.150.31
2
*
setup>2
Subnet Mask :255.255.255.0
Please Enter :255.0.0.0
(change)      —>  255.0.0.01
2
*
Default Gateway Setting
([3]Default Gateway)
Setting default gateway.
1
1 1
1
1 Enter “3” and press the “Enter” key.
2
2 2
2
2 Enter numerical value to be set and press the
“Enter” key.
Display gateway address after change (*).
Note
•If the values for IP Address, Subnet Mask or Gate-
wa y of the projector have been changed via Telnet,
the computer cannot be connected to the projector
depending on  the computer’s network settings.
User Name Setting
([4]User Name)
Carrying out security protection using user name.
1
1 1
1
1 Enter “4” and press the “Enter” key.
2
2 2
2
2 Enter user name and press the “Enter” key.
Display set user name (*).
Note
•User name can be up to 8 characters.
• You can input the  characters below :
a-z, A-Z, 0-9, -, _
• In the def ault state, user name is not set.
setup>3
note: “0.0.0.0” means “Using no default gateway.”
Gateway Address :0.0.0.0
Please Enter :192.168.150.1
(change)          —>  192.168.150.11
2
*
setup>4
User Name :
Please Enter : XG-MB67X
(change)        —>   XG-MB67X1
2*
Setting up the Projector Using RS-232C or Telnet 
						

							-24
Password Setting
([5]Password)
Carrying out security protection using password.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter password and press the “Enter” key.
Display set password (*).
Note
•Password can be up to 8 characters.
• You can input the  characters below :
a-z, A-Z, 0-9, -, _
• In the def ault state, the password is not set.
RS-232C Baud Rate Set-
ting ([6]RS-232C Baud Rate)
Setting of baud rate for RS-232C terminals.
1
1 1
1
1 Enter “6” and press the “Enter” key.
2
2 2
2
2 Select and enter the number 0 or 2 and press
the “Enter”  key.
Display set baud rate (*).
Note
•Set the projector’s baud rate to the same rate as
that  used by the computer.
setup>5
Password :
Please Enter :  sharppj
(change)        —>   sharppj1
2
*
Projector Name Setting
([7]Projector Name)
It is possible to assign a projector name.
1
1 1
1
1 Enter “7” and press the “Enter” key.
2
2 2
2
2 Enter projector name.
Display set projector name (*).
Note
•Projector name can be up to 12 characters.
• You can input the  characters below :
A-Z, 0-9, -, _,  (,), space
( When “a-z” are input, they are converted to “A-Z”
automatically.)
• It  is  the  same as the name which can be con-
firmed or  set, using RS-232C commands “PJN0”,
“PJN1”, “PJN2” and “PJN3”.
DHCP Client Setting
([8]DHCP Client)
Setting DHCP Client to “ON” or “OFF”.
Example: When setting DHCP Client to “ON”
1
1 1
1
1 Enter “8” and press the “Enter” key.
2
2 2
2
2 Enter “1” and press the “Enter” key.
Display the obtained values (*).
setup>6
0 ...  9600 bps
2 ... 115200 bps
Baud Rate Select[0, 2] :2
RS-232C Baud Rate : 115200 bps1
2
*
setup>7
Projector Name : XG-MB67X
Please Enter : MY XG-MB67X
(change)       —>   MY XG-MB67X1
2
*
setup>8
note: It sets DHCP Client.
0 ... OFF
1 ... ON
DHCP Select[0-1] : 1
DHCP Client : ON
Success get data from DHCP server.
[MAC Address      
 ] : [08:00:1F:B1:B7:74]
[IP Address           ] : [192.168.150.2]
[Subnet Mask        ] : [255.255.255.0]
[Default Gateway   ] : [0.0.0.0]
[DHCP IP Address] : [192.168.150.1]
1
2
*
Setting up the Projector Using RS-232C or Telnet 
						

							-25
Disconnecting All Connec-
tions ([D]Disconnect All)
It is possible to disconnect all the TCP/IP connec-
tions currently recognized by the projector. Even if
the COM Redirect port is fixed in the Busy status
due to a problem, it is possible to force the Ready
status back by carrying out this disconnection.1
1 1
1
1 Enter “d” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•If Disconnect All is performed, the connection to
the projector  via network  will be forcibly  discon-
nected.
Entering ADVANCED
SETUP MENU
([A]Advanced Setup)
Enters ADVANCED SETUP MENU.
1
1 1
1
1 Enter “a” and press the “Enter” key.
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)
If there is no input after a fixed time, the projector
automatically disconnects network connection using
the Auto Logout function. It is possible to set the time
until the projector is automatically disconnected in
units of a minute (from 1 to 65535 minutes).
1
1 1
1
1 Enter “1” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•If the set value is made 0, the Auto Logout func-
tion is disabled.
•
If an invalid number is entered, an error message
(“Parameter Error!”) will be displayed  and the
screen returns to the ADVANCED SETUP MENU.
Data Port Setting
(ADVANCED[2]Data Port)
Setting of TCP port number. It is possible to set in
the range of 1025 to 65535.
1
1 1
1
1 Enter “2” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Nor mally, use with the fac-
tory default setting.
setup>d
Disconnect All  Connections(y/n)?y
Now Disconnecting...1
2
setup>a
******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time [2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)
[9]Accept All IP Addr [0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
advanced>1
advanced>1
V alid range : 0 to 65535 (minute)
note: if you enter “0”, auto logout function will be disable.
Auto Logout Time : 5
Please Enter :15
(change)        —>  151
2
*
advanced>2
V alid range :1025 to 65535
Data Port :10002
Please Enter :10005
(change)          —>  100051
2
*
Setting up the Projector Using RS-232C or Telnet 
						

							-26
Carrying out Network Ping
Test
(ADVANCED[5]Network Ping Test)
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally.1
1 1
1
1 Enter “5” and press the “Enter” key.
2
2 2
2
2 Enter IP address of device to be tested and
press the “Enter” key.
Display entered IP address (*1).
Display test result (*2).
Note
•If the “Enter” key is pressed without entering an
IP address, the Ping destination IP address used
previously is  entered.
• If there is a fault with the connection, “Error: No
answer” is displayed after a 5 second retry. In this
case, please confirm the settings for the projector
and the computer, and contact your network ad-
ministrator.
Setting of Accept IP Ad-
dress 
(ADVANCED[6]Accept IP
Addr(1) - [8]Accept IP Addr(3))
It is possible to improve security of the projector by
allowing connection from only a prescribed IP ad-
dress. It is possible to set up to three IP addresses
allowing connection to the projector.
1
1 1
1
1 Enter “6”, “7” or “8” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•To  invalidate the Accept IP Address being cur-
rently set, enter “0.0.0.0”.
• If there is one or more Accept IP Addr being set,
no connections are allowed from IP addresses
that are not yet set. They can be cancelled using
[9]Accept All IP Addr.
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr)
Removes IP addresses set with “Accept IP Addr”.
1
1 1
1
1 Enter “9” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•At the point in time where “y” was entered, the
numerical values for Accept IP Addr(1)-(3) are
reset to “0.0.0.0”.
• If “n” is entered, setting is not altered.
advanced>5
Ping dest IP addr :192.168.150.1
Please Enter :192.168.150.152
(change)         —>  192.168.150.152
32 bytes from 192.168.150.152: icmp_seq = 1, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 2, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 3, time = 0 ms
32 bytes from 192.168.150.152: icmp_seq = 4, time = 0 ms1
2
*1
*2advanced>6
Accept IP Addr(1) : 0.0.0.0
Please Enter : 192.168.150.152
(change)         —>   192.168.150.1521
2
*
advanced>9
Accept All  IP Addresses(y/n)?  y1
2
Setting up the Projector Using RS-232C or Telnet 
						

							-27
Setting of Search Port
(ADVANCED[0]Search Port)
Sets the port number used when searching for the
projector from the network.1
1 1
1
1 Enter “0” and press the “Enter” key.
2
2 2
2
2 Enter numerical value and press the “Enter” key.
Display set numerical value (*).
Note
•Set according to need. Nor mally, use with the fac-
tory default setting.
Return to Default Settings
(ADVANCED[!]Restore Default
Setting)
Returns all menu setting values to the default state.
1
1 1
1
1 Enter “!” and press the “Enter” key.
2
2 2
2
2 Enter “y” and press the “Enter” key.
Note
•If the values for IP Address, Subnet Mask or Gate-
wa y of the projector have been  returned to the
default settings  via Telnet, the computer cannot
be connected to the projector  depending on the
computer’s network settings.
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)
Returns to the main SETUP MENU.
1
1 1
1
1 Enter “q” and press the “Enter” key.
Returns to the SETUP MENU.
advanced>0
Please Enter Port Number for Search from Computer.
Valid range : 1025 to 65535
Search Port : 5006
Please Enter : 5004
(change)         —>   50041
2
*
advanced>!
Restore All Setting to Default(y/n)? y
— User Setting Initialized —1
2
advanced>q
---------------------------------SETUP MENU-----------------------------\
---
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>1
Setting up the Projector Using RS-232C or Telnet 
						

							-28
Communication cannot be established with the projector
When connecting the projector using serial-connection
\Check that the RS-232C terminal of the projector and a computer or the commercially
available controller are connected correctly.
\ Check that the RS-232C cable is a cross-over cable.
\ Check that the RS-232C port setting for the projector corresponds to the setting for the
computer or the commercially available controller.
When connecting the projector to a computer using network (LAN)-
connection
\Check that the cable’s connector is firmly inserted in the LAN terminal of the projector.
\ Check that the cable is firmly inserted into a LAN port for a computer or a network device
such as a hub.
\ Check that the LAN cable is a Category 5 cable.
\ Check that the LAN cable is a cross-over cable when connecting the projector to a computer
directly.
\Check that the LAN cable is a straight-through cable when connecting the projector with a
network device such as a hub.
\Check that the power supply is turned on for the network device such as a hub between the
projector and a computer.
Check the network settings for the computer and the projector
\Check the following network settings for the projector.
• IP Address
Check that the IP address for the projector is not duplicated on the network.
• Subnet Mask
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for
the projector and the default gateway setting for the computer are the same:
•The subnet masks for the projector and the computer should be the same.
• The IP address parts shown by the subnet mask for the projector and the computer should
be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
• Gateway
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for
the projector and the default gateway setting for the computer are the same:
•The subnets for the projector and the computer should be the same.
• The IP address parts shown by the subnet mask for the projector and the computer should
be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
Note
•When “DHCP Client” is set to “OFF” on the projector
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Gateway address : 0.0.0.0 (Not Used)
• For network settings for the projector, refer to page 
11 .
Troubleshooting 
						

							-29
Troubleshooting
\ Take the following steps for checking the network settings for the computer.
1. Open a command prompt (MS-DOS Prompt). •In the case of Windows
® 98 or 98SE: click “START”  ➔ “Programs”  ➔ “MS-DOS Prompt” in
order.
• In the case of Windows
® Me: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “MS-DOS
Prompt” in order.
• In the case of Windows
® 2000: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “Command
Prompt” in order.
• In the case of Windows
® XP: click “START”  ➔ “All Programs”  ➔ “Accessories”  ➔ “Command
Prompt” in order.
2. After launching the command prompt (MS-DOS Prompt), enter the command \
“ipconfig”,
and press the “Enter” key.
Note
•Communication may not be established even after carrying out the network settings
for the computer. In such cases, restart your computer.
C:\>ipconfig
Note
• Usage examples of ipconfig
C:\>ipconfig /? displays how to use “ipconfig.exe”.
C:\>ipconfig displays the set IP address, subnet mask and default gateway.
C:\>ipconfig /all displays all the setting information related to TCP/IP.
3. To return to the Windows® screen, enter “exit” and press the “Enter” key. 
						

							-30
\Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check
if an IP address is set.
1. Open a command prompt (MS-DOS Prompt).
•In the case of Windows
® 98 or 98SE: click “START”  ➔ “Programs”  ➔ “MS-DOS Prompt” in
order.
• In the case of Windows
® Me: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “MS-DOS
Prompt” in order.
• In the case of Windows
® 2000: click “START”  ➔ “Programs”  ➔ “Accessories”  ➔ “Command
Prompt” in order.
• In the case of Windows
® XP: click “START”  ➔ “All Programs”  ➔ “Accessories”  ➔ “Command
Prompt” in order.
2. After launching the command prompt (MS-DOS Prompt) enter a command “PING”.
Entry example C:\>Ping XXX.XXX.XXX.XXX
“XXX.XXX.XXX.XXX” should be entered with an IP address to be connected to, such as
the projector.
3. When connecting normally, the display will be as follows. (The screen may be slightly different depending on the OS type).
 when the IP address connected to is “192.168.150.2”
4. When a command cannot be sent, “Request time out” will be displayed.Check the network setting again.
If communication can still not be established properly, contact your network administrator.
5. To return to the Windows
® screen, enter “exit” and then press the “Enter” key.
A connection cannot be made because you have forgotten your user name or your password.
\ Initialize the settings. (See page  51 of the projector’s operation manual.)
\ After the initialization, carry out setting again.
Troubleshooting