Sharp Xg E3000u Projector User Manual

E-21
RGB Adjustment Controls
nWhen displaying computer patterns which repeat every other dot (tiling, vertical stripes, etc.),
interference may occur between the LCD pixels, causing flickering, vertical stripes, or contrast
irregularities in portions of the screen. Should this occur, use the ADJUSTMENT 
/ buttons
for HORIZONTAL (LEFT/RIGHT) and VERTICAL (UP/DOWN) position adjustments to adjust
for the optimum picture.
2
RGB1  INPUT  ADJ.
PHASEH-POSV-POSMODERESET
MEMORY SELECT  +
0 0
0
0
:SEL....

E-22
1When RGB 1 or 2 is selected.
Computer Mode Memory Adjustments
·The projector has been preset with different modes for
use with SVGA and other compatible computers.
However, 7 memory positions are provided to store
mode adjustments.
·Each memory position can be used to store mode
adjustments to match the computer.
1. Press the ENTER button to select the
Memory Adjustment mode.
·Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to
select ÒRGB1 INPUT ADJ.Ó...

E-23
ON/OFF
POWER
LAMP
TEMP.
Basic Operation of the Projector
1
When the power is on, the LAMP
REPLACEMENT indicator flashes
to show the operating condition of
the lamp.
Green: Lamp is ready
Flashing green: Warming up
Red: Change bulb
ONA.C.120V
C.A.120V
OFF
1AC cord
1. Connect the AC cord.
Connect the supplied AC cord to the AC inlet on the side
of the projector .
2. Turn on the MAIN POWER.
Press the MAIN POWER switch on the side of the projec-
tor. The POWER indicator lights red and the projector...

E-24
On-Screen Display
LANGUAGE
:SEL.:ENTERENTER:ENDMENU
NEDERLANDS ESPAÑOL
DEUTSCH
ENGLISH
SVENSKA ITALIANO FRANÇAIS
4. Select one of eight ON-SCREEN DISPLAY
languages.
You can return to the previous screen by selecting the
uppermost item (turquoise) with the ADJUSTMENT 
/
buttons (in this case, LANGUAGE) and then pressing
the ENTER button.
The on-screen display is set to English at the factory. The
language for the unitÕs ON-SCREEN DISPLAY can be set
to English, German, Spanish, Dutch, French,...

E-25
6. Select input.
Press the INPUT SELECT button on the projector to
switch the picture input. When you press the button, the
current input mode is displayed for about 4 seconds. If
you press the button again while the input mode is
displayed, the mode changes as shown on the left.
Confirm the selected input terminal and press the INPUT
SELECT button.
Notes:
·This can be selected directly using the VIDEO 1, VIDEO 2, DATA1 and
DATA2 buttons on the remote control.
·In VIDEO mode, the system being...

E-26
Adjusting the Picture
3
·This projectorÕs picture is factory preset to standard
settings. However, you can adjust it to suit your own
preferences with the ADJUSTMENT buttons on the
projector and the remote control.
·The adjustments can be memorized in RGB 1, RGB 2
or VIDEO separately.
·Four picture modes can be adjusted: ÒPICTURE,Ó
ÒBRIGHT,Ó ÒRED,Ó  and ÒBLUE.Ó
Adjusting the Picture
1. Use the MENU button to select the mode
to be adjusted.
·When the MENU button is pressed, the MENU mode is
indicated...

E-27
Adjusting the Audio
On-Screen Display
AUDIO
TREBLEBASSRESET
0 0
0
:SEL.
:ADJ.:ENDMENU
 R L + - + -
BALANCE
ADJUSTMENT  button
Increased audio from the
left speaker
Weaker treble
Weaker bassADJUSTMENT  button
Increased audio from the
right speaker
Stronger treble
Stronger bassSelected items
BALANCE
TREBLE
BASS
·The projectorÕs audio is factory preset to the standard
setting. However, you can adjust it to suit your own
preference with the ADJUSTMENT buttons on the
projector or the remote control.
·You...

E-28
Setting Up the System
nUsing this function, you can check the input signal and
lamp usage time, and select the remote mouse and DC
5V output.
Checking the system and lamp usage time
·Press the MENU button. Select ÒSYSTEM SETUPÓ with the
ADJUSTMENT / buttons. Then press the ENTER button to
change to the picture indicated on the left.
·The current system conditions, including the lamp usage time,
will be displayed on the screen.
·Press the MENU button to select the normal screen mode.
Note:
·In the...

E-29
Using the Black Screen Function
nThis projector is equipped with a Black Screen Func-
tion. This function can be used to black out the presen-
tation image.
¥ Press the BLACK SCREEN button on the projector or
the remote control to display the black screen.  Press
the BLACK SCREEN button again to return to the
presentation image.
Note:
¥ When BLK SCRN DISP is set to OFF, the On-Screen Display (ÒBLACK
SCREENÓ) will not appear during black screen.  See below.
BLACK SCREEN On-Screen DisplayLCD...

E-30
On-Screen Display
Using the Blue Screen Function
nThis projector is equipped with a Blue Screen function
that will turn the screen blue when the video input
terminal is not connected to anything, or the video
component is turned off.
·Press the MENU button. While the MENU screen is
displayed, press the ADJUSTMENT 
/ buttons to
select ÒIMAGE ADJ.Ó Then press the ENTER button to
display the IMAGE ADJ. screen as shown. Press the
ADJUSTMENT 
/ buttons to select ÒBLUE SCREEN,Ó
and press the ADJUSTMENT 
/...