Sharp Tl M5200 Operation Manual

9
Preparation

Connecting Peripheral Equipment
Connecting external speakers
Be sure to use external speakers with an impedance 
of 4 Ω and a rated input of at least 5 W.
1 While pushing the tab, insert the tip of the cable.
2 Release the tab.
•	Be	sure	to	connect	the	+	and	-	terminals	and	the	left	and	
right	speakers	properly.
•	Avoid	short	circuiting	the	+	and	-	terminals.
•	It	is	recommended	that	you	use	the	optional	Sharp	 speaker 	unit 	(AN-52SP2/AN-46SP2) 	for 	external 	speakers.
N o t...

0
Controlling the monitor by a computer
When the RS-3C terminal on the monitor is connected to the RS-3C serial terminal on the computer, 
or when the LAN terminal on the monitor is connected to the LAN terminal on the computer, the computer 
can be used to control the monitor. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for 
details.
n When connecting to a computer using an RS-232C serial control cable
To RS-3C terminal
To RS-3C terminal...


Preparation
Connecting the Power Cord
Caution
• Do not use a power cord other than the one 
supplied with the monitor.
Be sure to use a power outlet of 
AC 120 V (60 Hz).
Using power supply other than the 
one specified may cause fire.
• Place the monitor close to the AC outlet, and 
keep the power plug within reach.
•  This product must only be connected to an AC 
0 V, 60 Hz, grounded (3-prong) outlet. 
 
Connecting it to any other kind of outlet will 
damage the product and...


Preparing the Remote Control
Installing the batteries
1Pull down the tab on the cover 
and remove the cover towards 
the direction of the arrow.
2Insert the batteries.
• Insert the batteries making sure 
the polarities correctly match 
the +  and -  marks inside the 
battery compartment.
3Insert the lower tab of the 
cover into the opening, and 
lower the cover until it clicks in 
place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the 
precautions below....

23
Operation
Turning the Monitor On/Off
Turning on the power
Press POWER on the monitor.
•  POWER indicator (Green): The monitor is on.
•  After turning the power “ON” by pressing 
POWER 
on the monitor, you can turn the power ON by 
pressing ON on the remote control.
POWER button
POWER indicator
Caution
• When switching the POWER, ON or STANDBY 
buttons off and back on, always wait for at least 
5 seconds. A short interval may result in a 
malfunction.
Turning off the power
ON buttonSTANDBY button...

24
COMPUTER (/), DVI, HDMI, S-VIDEO, VIDEO buttons
AV MUTE button
VOL (Volume) buttons (+/-)
Operating with the Remote Control
Switching the input mode
Select the appropriate input mode for the connected 
equipment.
Press COMPUTER (1/2), DVI, HDMI, S-VIDEO or 
VIDEO to select the input mode.
•  When you press 
INPUT on the monitor, the 
INPUT list appears.
  Press 
▲/▼ to switch the input mode.
Adjusting the volume
Press VOL +/– to adjust the volume.
•  You can also adjust the volume using...

25
Operation
Operating with the Remote Control
Resize mode
This function allows you to modify or customize the Resize mode to enhance the input image. Depending on 
the input signal, you can choose a desired image.
1 Press RESIZE.
•  The Resize mode menu appears.
•  The menu lists the Resize mode options 
selectable for the type of signal currently 
received.
Zoom 4:9
S.Stretch
Full
Resize
Normal
Cinema 6:9
Cinema 4:9
2 Press RESIZE or ▲/▼ while the Resize mode menu is displayed on the...

26

Operating with the Remote Control
Selectable itemsDescription
Cinema 16:9
NormalZoom 14:9S. Stretch
Cinema 14:9Cinema 16:9Full
For 6:9 letterbox pictures. The top and bottom of the image 
may be cut off depending on the input signal.
Cinema 14:9
NormalZoom 14:9S. Stretch
Cinema 14:9Cinema 16:9Full
For 4:9 letterbox pictures. The top and bottom of the image 
may be cut off depending on the input signal.
Dot by DotDisplay an image with the same number of pixels on the 
screen (only when...

27
Operation

Operating with the Remote Control
FREEZE button
AUTO SYNC button
MAGNIFY buttons
RETURN button
AV MODE button
Auto Sync adjustment  
(Auto Sync)
“Clock”, “Phase”, “H-Position”, and “V-Position” are 
automatically adjusted.
Press AUTO SYNC.
•  You can also perform Auto Sync adjustment from 
the “Setup” menu.
Freezing a moving image
1 Press FREEZE.
•  The image is frozen.
2 Press FREEZE again to return to the moving image from the currently connected device.
•	The	still	image	automatically...

28

Operating with the Remote Control
Split-screen viewing
You can display two pictures on the screen simultaneously.
P&P button
SELECT button COMPUTER (/), DVI, 
HDMI, S-VIDEO, VIDEO 
buttons
1 Press P&P.
•  Split-screen appears.
•  The current input is moved to the left side screen display and surrounded by a blue frame.
•  The other input appears on the right side screen display.
1 2 3 4 5 6 7 89 10 11 12
5101520253035
2 3 4 5 6 7 89 10
2 Press SELECT to set either screen to be active.
•...