Sharp Projector Pg M25x User Manual

Appendix
Appendix
PG-M25X#E#p107_115.p6502.4.29, 3:25 PM 107 

Carrying the Projector
How to Use the
Carrying Case
When transporting the projector, make sure
to retract the antenna, cover the lens with the
lens cap, and place the projector in the
included carrying case.
1Open the cover of the carrying
case.
2Remove the inner padding
from the carrying case, and
fold it in the direction of the
arrows.
3Reinsert the inner padding into
the carrying case.
Info
•Be sure to insert the inner padding
to protect the lens and the projector.
4Place the projector and the ac-...

Appendix
-109
Cleaning the lens

Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coat-
ing film on the surface of the lens.

As the surface of the lens can easily get dam-
aged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents

Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Cleaning
Paper
Maintenance
Cleaning the...

-110
Maintenance Indicators
Info
•If the TEMPERATURE WARNING indicator illuminates, and the power turns off, follow the above possible
solutions and then wait until the projector has cooled down completely before plugging in the power cord and
turning the power back on. (At least 5 minutes.)
•If the power is turned off and then turned on again, as during a brief test, the LAMP REPLACEMENT indica-
tor may be triggered, preventing the power from going on. Should this occur, take the power cord out of the...

Appendix
-111
Lamp

It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative
hours of use or when you notice a significant deterioration of the picture and color quality. The lamp
usage time can be checked with the on-screen display. See page 58.

For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service
Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor...

POWER button
Regarding the Lamp (cont.)
Removing and Install-
ing the Lamp Unit
Info
•Be sure to remove the lamp unit by the
handle. Be sure not to touch the glass
surface of the lamp unit or the inside of
the projector.
•To avoid injury to yourself and damage
to the lamp, be sure to carefully follow
the steps below.
•Do not loosen other screws except for the
lamp cover and lamp unit.
•Please refer to the installation manual
included with the lamp unit.
•Make sure to read the manual that came
included...

Appendix
-113
AC socket
POWER button
Adjustment buttons
(
"| "|"| "|
"|)
ENTER buttonUser service screw
4Loosen the lamp unit.
•Remove the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of
the arrow.
5Insert the new lamp unit.
•Press the lamp unit firmly into the lamp
unit compartment. Fasten the secur-
ing screws.
6Attach the lamp unit cover.
•Slide the lamp unit cover in the direc-
tion of the arrow. Then tighten the user
service...

-114
12
43
17
••••••••• ~ •••••••••
••••
 ~ ••••
••••
 ~ ••••
24
18 23
C3
2 1
916
C1
C2
C4
C5
8 7
• DVI Digital INPUT
Pin No. Signal Pin No. Signal
1 T.M.D.S data 2–16 Hot plug detection
2 T.M.D.S data 2+ 17 T.M.D.S data 0–
3 T.M.D.S data 2 shield 18 T.M.D.S data 0+
4 Not connected 19 T.M.D.S data 0 shield
5 Not connected 20 Not connected
6 DDC clock 21 Not connected
7 DDC data 22 T.M.D.S clock shield
8 Not connected 23 T.M.D.S clock+
9 T.M.D.S data 1–24 T.M.D.S clock–
10 T.M.D.S data 1+ C1 Not...

Appendix
-115
Computer Compatibility Chart
* Temporary noise  may be visible with vertical frequencies above 100Hz if OSD functions are activated.
Note
•This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this
occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how
to change display modes can be found in your notebook computer’s operation manual.
•When this projector receives 640 ×...

-116
Troubleshooting
Check
•Projector power cord is not plugged into the wall outlet.
•Power to the external connected devices is off.
•The selected input mode is wrong.
•Cables incorrectly connected to side panel of the projector.
•Remote control batteries have run out.
•
External output has not been set when connecting notebook computer.
•The AV MUTE display appears.
•The cover of the lamp unit is not installed correctly.
•Cables incorrectly connected to the side panel of the projector.
•“Bright” is...