Sharp Projector Pg M15x User Manual

Operation
19
58
7
6
Basic Operations
3Rotate the ZOOM knob. The image can be
adjusted to the desired size within the zoom range.
4Rotate the FOCUS ring until the image on the
screen becomes clear.
5Press INPUT to select the desired input mode.
Press INPUT again to change the mode. Projector
•When the selected input signal is being received, “Adjusting
The Image” will be displayed.
•When no signal is being received, “NO SIGNAL” will be
displayed. When a signal that the projector is not preset to
receive...

Operation
20
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Move the projector forward or backward if the edges of the image are distorted.
•The projector lens should be centered in the middle of the screen. If the lens center is not perpendicular to the screen, the image will be
distorted, making viewing difficult.
•Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out...

Operation
21
Setting up the Screen
PG-M15S
Throw distance ratio
x: Picture size (Diag.) (inches)
L
1: Maximum projection distance (feet)L2: Minimum projection distance (feet)
H: Distance from the lens center to the
  bottom of the image (inches)
17 41⁄64
(44.8 cm)
14 7⁄64
(35.8 cm)
10 37⁄64
(26.9 cm)
7 4⁄64
(17.9 cm)
5 59⁄64
(15.1 cm)
5 5⁄64
(12.9 cm)
4 15⁄64
(10.8 cm)
2 53⁄64
(7.2 cm) Distance from the lens center to
the
 bottom of the image (H)
Maximum (L1)
41 8
(12.7 m)*1
33 4
(10.2...

Operation
22
Setting up the Screen
Using the Adjustment Feet
You can adjust the height of the image by raising the projector with the
foot release.
1Lift the projector and press HEIGHT ADJUST.
(The adjuster comes out.)
2While pressing HEIGHT ADJUST, lower the projector to adjust
the height. (Adjustable up to approximately 8° from the standard
position)
3Remove your finger from HEIGHT ADJUST at the desired angle.
4Rotate the rear adjuster to adjust the projector exactly.
(Adjustable up to approximately 1°...

Operation
23
1 2
2
Setting up the Screen
Digital Keystone Correction
•When the image is distorted due to the projection
angle, the digital keystone correction function allows
you to correct it.
•The digital keystone correction can be made by
pressing KEYSTONE (/).
ProjectorUsing the KEYSTONE buttons
1Press KEYSTONE (/) to adjust the setting.
2To reset the keystone setting, press BACK.
Remote control
(GUI) On-screen Display
Lamp Timer
KeystonePicture
Options Fine Sync
Language
PRJ Mode
END SELECT BACK...

Operation
24
Operating the Wireless Mouse from the Remote Control
You can use the remote control to operate the mouse of the computer image projected to the screen.
Connecting the projector to a computer using a USB mouse control cable
1Connect one end of the supplied USB mouse control cable to the RS-232C/MOUSE port on the projector.
2Connect the other end to the corresponding terminal on the computer.
Connecting to the USB port on a PC or Macintosh
USB mouse control
cable
To USB port
Computer
•Windows...

Operation
25
Remote Control/Wireless Mouse Positioning
•The remote control and the wireless mouse functions can be used to control the projector within the ranges
shown below.
•The remote control can be used with the wireless mouse functions to control the mouse operation on the computer
connected to the projector.
•The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the
signal may differ due to the screen material.
Operating the...

26
Operation
ContrastPicture
Options
Language
PRJ Mode
END SELECT BACK ENTERBright
Color
Tint
Sharp
Red
Blue
CLR Temp0
0
0
0
0
0
0
High
Reset
Using the GUI (Graphical User Interface) Menu Screens
This projector has four sets of menu screens (INPUT 1 (DVI), INPUT 1 (RGB), INPUT 1 (COMPONENT) and INPUT
2 (S-VIDEO) or 3 (VIDEO)) that allow you to adjust the image and various projector settings. These menu screens
can be operated from the projector or the remote control with the following buttons.
(GUI)...

27
Operation
Using the GUI (Graphical User Interface) Menu Screens
ContrastPicture
Options Fine Sync
Language
PRJ Mode
END SELECT BACK ENTERBright
Red
Blue
CLR Temp
Reset0
0
0
0
High
4, 5
64Press ∂/ƒ to select an adjustment item in the
sub menu.
5Press ENTER to activate the selected adjustment
item.
6To display a single adjustment item, press ENTER
after selecting the item.
Only the menu bar and the selected adjustment
item will appear.
ContrastPicture
Options Fine Sync
Language
PRJ Mode
END SELECT BACK...

28
Operation
Items on the INPUT 1 (DVI) Mode Menu Bar
Using the GUI (Graphical User Interface) Menu Screens
Main menu Main menuSub menu Sub menu
Fine Sync
Options Lamp Timer
AV Mute Disp.
Language English
PRJ Mode
Ceiling
Front
Ceiling
Rear Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Front
Rear OSD Display
Auto Power Off Phase Clock
H-Pos
V-Pos
Signal Info Contrast Picture
Bright
Red
Blue
Reset
BackgroundOFF Keystone
ON
ON
OFF
Auto Source ON
OFF ON
127 127
OFF
None BlueResolution
Hor...