Sharp Projector Pg M15x User Manual

							Important
Information
Setup & Connections
Operation
Useful FeaturesMaintenance &
TroubleshootingAppendix
OPERATION MANUAL
MODEL
DIGITAL
MULTIMEDIA
PROJECTOR 
						

							SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked 
 or  and of the same rating as
above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in
a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 3A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/
EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/
68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la
directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla
direttiva 93/68/EEC.
« „ͷًÛÙ·ÛÁ ·ıÙfi ·ÌÙ·ÔÍÒflÌÂÙ·È ÛÙÈÚ ··ÈÙfiÛÂÈÚ Ù˘Ì Ô‰Á„È˛Ì ÙÁÚ EıÒ˘·˙ÍfiÚ EÌ˘ÛÁÚ 89/336/EOK
Í·È 73/23/EOK, ¸˘Ú ÔÈ Í·ÌÔÌÈÛÏÔfl ·ıÙÔfl ÛıÏÎÁÒ˛ËÁÍ·Ì ·¸ ÙÁÌ Ô‰Á„fl· 93/68/EOK.
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida
pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la
93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/
EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC. 
						

							Important
Information
1
IMPORTANT
For your assistance in reporting the loss or theft of your
projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that
you have checked the contents of the carton thoroughly
against the list of “Supplied Accessories” on page 12.
Before using the projector, please read this operation manual carefully.
OPERATION MANUALENGLISH
Model No.: PG-
M15X
Serial No.:
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
U.S.A. ONLY
WARNING:High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WARNING:FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
Model No.: PG-
M15S
Serial No.:
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY 
						

							Important
Information
2
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and high intensity discharge lamp (HID lamp) containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org .
Caution Concerning the Lamp Replacement
See “Replacing the Projection Lamp” on pages 47 and 48.
REM PLACEMENT DE LA  LAMPE. PRECAUTIONS A OBSERVER LORS DU
USER SERVICE SCREWS
VIS POUR ENTRETIEN PAR L’UTILISATEUR
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.  
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE 
AVANT DE PROCEDER AU REMPLACEMENT  DE  LA  LAMPE. 
NE REMPLACER QUE PAR UNE LAMPE SHARP DE  TYPE BQC-PGM15X// 1. 
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE  LA LAMPE AVANT  DE PROCEDER  A  L’ENTRETIEN.  
LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION.  DANGER  POTENTIEL 
DE PARTICULES  DE VERRE EN  CAS D’ECLATEMENT DE  LA  L A M P E .
A MANIPULER AVEC  PRECAUTION, SE REPORTER A U  MODE D’EMPLOI. BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE 
INSIDE.   ALLOW  1 HOUR TO COOL BEFORE REPLACING THE LAMP.
REPLACE  WITH SAME  SHARP LAMP UNIT  TYPE BQC- PGM15X / / 1 ONLY.
UV RADIATION : CAN  CAUSE EYE DAMAGE. TURN OFF LAMP  BEFORE 
SERVICING. MEDIUM PRESSURE LAMP  : RISK OF  EXPLOSION. POTENTIAL
HAZARD OF GLASS PARTICLES IF  LAMP HAS RUPTURED.   HANDLE WITH
CARE.  SEE OPERATION MANUAL.
LAMP REPLACEMENT CAUTION
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During
normal operation, when turning the power off, always use the ON/OFF button on the projector or the POWER
button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER
CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures. 
						

							Important
Information
3
Electrical energy can perform many useful functions. This product has been engineered and manufactured to ensure your
personal safety. However IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order
not to defeat the safeguards incorporated into this Projector, observe the following basic rules for its installation, use and
servicing. For your own protection and reliable usage of your projector, please be sure to read these “IMPORTANT
SAFEGUARDS” carefully before use.
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained
for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
•Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
•Never use strong detergents or solvents such as alcohol
or thinner.
•Use a blower or lens paper to clean the lens, and be
careful not to scratch or mar the lens.
6. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a
bathtub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to
the product. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
10. Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product and
to protect it from overheating. The openings should never
be covered or blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of
plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.13. Power-Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they
exit from the product.
14. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the power cord. This will prevent damage to
the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
e. If the product has been dropped or damaged in any
way.
f. If the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating
condition.
21. Heat
This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
IMPORTANT SAFEGUARDS 
						

							Important
Information
4
IMPORTANT SAFEGUARDS
24. Lamp Replacement
•Be sure to replace the lamp when the LAMP indicator
comes on. If you continue to use the lamp after 1,500
hours of usage, the lamp will turn off (See pages 47 and
48).
25. Fire and Shock Precautions
•Ensure that there is sufficient ventilation and that vents
are unobstructed to prevent the buildup of heat inside
the product. Allow at least 7 
7/8 inches (20 cm) of space
between the unit and surrounding obstructions.
•Prevent foreign objects such as paper clips and bits of
paper from falling into the product. Do not attempt to
retrieve any objects that fell into the product. Do not
insert any metal objects such as a wire or screwdriver
into the product. If something should fall into the product,
immediately disconnect the power cable from the
product and have the object removed by a Sharp
Authorized Projector Dealer or Service Center.
•Do not place any liquids on top of the product.
•Do not look into the lens while the product is on.
Serious damage to your eyes could result. 22. Installation
•For best results, use the product in a darkened room.
• Place the product on a flat, level surface in a dry area
away from dust and moisture.
•Do not place the product in direct sunlight, near heaters
or heat radiating appliances.
•Exposure to direct sunlight, smoke or steam can harm
internal components.
•Handle the product carefully. Dropping or jarring can
damage internal components.
•Do not place heavy objects on top of the product.
23. Power Supply
•The product is designed to operate on a power supply
of 100 to 240 V 50/60 Hz AC. Ensure that your power
supply fits these requirements before attempting to use
the unit.
•For PLUGGABLE EQUIPMENT, the socket-outlet shall
be installed near the equipment and shall be accessible.
•Disconnect the power cable (main lead) from the power
outlet after using the product.
Before disconnecting the power cable, make sure the
POWER indicator lamp is orange and not flashing.
•Handle the power cable carefully and avoid excessive
bending. A damaged cord can cause electric shock or
fire.
IMPORTANT
•DLP (Digital Light Processing) and DMD (Digital
Micromirror Device) are trademarks of Texas Instruments,
Inc.
•Microsoft and Windows are registered trademarks in the
United States and other countries of Microsoft
Corporation.
•PC/AT is a registered trademark in the United States of
International Business Machines Corporation.
•Macintosh is a registered trademark in the United States
and other countries of Apple Computer, Inc.
•The other company and product names mentioned are
trademarks or registered trademarks of each respective
company. 
						

							Important
Information
5
Outstanding Features
1. SMALL, LIGHTWEIGHT & USER-FRIENDLY DESIGN
Small and lightweight design (3.5 lbs/1.6 kg, 2.0 liter) enhances projector portability.
2. 1.2
 MANUAL ZOOM/FOCUS
Adjusts image size without relocating the projector.
3. EASY-TO-USE GRAPHICAL USER INTERFACE (GUI)
Multi-color interface lets you select functions easily.
4. AUTO SYNC TECHNOLOGY FOR AUTOMATIC IMAGE
OPTIMIZATION
Automatically makes any necessary adjustments for perfectly synced computer images.
5. HIGH RESOLUTION IMAGES WITH INTELLIGENT
COMPRESSION TECHNOLOGY
PG-M15X
Native XGA resolution (1,024  768) and compatibility with SXGA using intelligent compression
PG-M15S
Native SVGA resolution (800  600) and compatibility with SXGA and XGA using intelligent compression
6. DIRECT DIGITAL COMPUTER INPUT (DVI)
Signals remain digital from the source device to the projector resulting in sharper, clearer, noiseless and adjustment-
free computer images.
7. RGB MONITOR OUTPUT TERMINAL
Presenters can simultaneously view their presentation on a LCD or CRT display while the image is being projected to
an audience.
8.ANTI-ALIASING DIGITAL KEYSTONE CORRECTION
Digitally adjusts image projected at an angle to maintain overall image quality
and brightness.
9. WIRELESS MOUSE REMOTE CONTROL
Allows you to operate the projector and your computer mouse.
10. COLOR TEMPERATURE  ADJUSTMENT
Ensures perfect color rendering. 
						

							Important
Information
6
Important Information
Contents
IMPORTANT SAFEGUARDS …………………… 3
Outstanding Features …………………………… 5
Contents …………………………………………… 6
Usage Guidelines ………………………………… 7
How to Access the PDF Operation Manuals
(for Windows and Macintosh) ……………… 8
Part Names ………………………………………… 9
Setup & Connections
Supplied Accessories……………………………12
Connecting the Projector………………………13
Basic Operations…………………………………18
Setting up the Screen……………………………20
Operating the Wireless Mouse from the
Remote Control………………………………24
Using the GUI (Graphical User Interface)
Menu Screens…………………………………26
Selecting the On-screen Display Language…30
Selecting the Video Input System Mode
(INPUT 2 or 3 only)……………………………30
Picture Adjustments………………………………31
Adjusting the Picture …………………………… 31
Selecting the Color Temperature …………… 32
Computer Image Adjustments
(INPUT 1 (RGB) mode only)…………………33
Auto Sync Adjustment ………………………… 33
Adjusting the Computer Image ……………… 33
Operation
Useful Features
Freeze Function……………………………………34
Digital Image Magnification……………………35
Selecting the Picture Display Mode……………36
Gamma Correction………………………………38
Checking the Input Signal
(INPUT 1 (DVI) or (RGB) mode only)…………39
Checking the Lamp Usage Time………………39
Turning On/Off the AV Mute Message…………40
On-screen Display Override Function…………41
Automatic Power Shutoff Function……………42
Detecting the Input Source Automatically……43
Selecting a Background Image…………………43
Reverse/Invert Image Function…………………44
Setup & Connections
Operation
Useful Features
Maintenance &
Troubleshooting
Appendix
Lamp/Maintenance Indicators…………………46
Replacing the Projection Lamp…………………47
Using the Kensington Lock……………………48
Troubleshooting……………………………………48
Appendix
Maintenance & Troubleshooting
Using the Soft Carrying Pouch…………………49
Connection Pin Assignments……………………50
RS-232C Port Specifications……………………52
Computer Compatibility Chart…………………53
Specifications………………………………………54
Dimensions…………………………………………55
Glossary……………………………………………56
Index…………………………………………………57
For SHARP Assistance…………………………58 
						

							Important
Information
7
Temperature Monitor Function
If the projector starts to overheat due to setup problems, “TEMP.” will appear in
the lower-left corner of the picture. If the temperature continues to rise, the lamp
will turn off, the TEMPERATURE WARNING indicator on the projector will flash,
and after a 90-second cooling-off period the power will shut off. Refer to “Lamp/
Maintenance Indicators” on page 46, for details.
•The cooling fan regulates the internal temperature, and its performance is automatically
controlled. The sound of the fan may change during projector operation due to changes
in the fan speed.
Lamp Monitor Function
When the projector is turned on after the lamp has been used for 1,400 hours,
“LAMP” will appear in the lower-left corner of the picture to advise you to replace
the lamp. See pages 47 and 48 for lamp replacement. If the lamp has been used
for 1,500 hours, the projector power will automatically turn off and the projector
will enter standby mode. Refer to “Lamp/Maintenance Indicators” on page 46,
for details.
Usage Guidelines
Caution Concerning the Lamp Unit
Potential hazard of glass particles if lamp ruptures. Please have Sharp Authorized
Projector Dealer or Service Center replace lamp if rupture occurs.
See “Replacing the Projection Lamp” on pages 47 and 48.
Cautions Concerning the Setup of the Projector
For minimal servicing and to maintain high image quality, SHARP recommends
that this projector be installed in an area free from humidity, dust and cigarette
smoke. When the projector is subjected to these environments, the lens must be
cleaned more often. Periodically the projector should be cleaned internally. As
long as the projector is properly maintained in this manner, use in these
environments will not reduce the overall operation life. Please note that all internal
cleaning must be performed by a Sharp Authorized Projector Dealer or Service
Center.
•Do not expose the projector to extreme heat or cold.
Operating temperature: 41°F to 95°F (5°C to 35°C)
Storage temperature: 14°F to 140°F (10°C to 60°C)
•The mark shown on the left calls the user’s attention to locations on the projector
that emit intense heat during operation.
•The exhaust vent, the lamp cage cover and adjacent areas may be extremely
hot during projector operation. To prevent injury, do not touch these areas until
they have sufficiently cooled.
•Allow at least 4 inches (10 cm) of space between the cooling fan (exhaust
vent) and the nearest wall or obstruction.
•If the cooling fan becomes obstructed, a protection device will automatically
turn off the projector lamp. This does not indicate a malfunction. Remove the
projector power cord from the wall outlet and wait at least 10 minutes. Then
reconnect the power cord and restart the projector. This will return the projector
to normal operating condition.
Notes on Operation
95˚F
(35˚C)
41˚F
(5˚C)
CAUTION
PRECAUCIÓN
PRÉCAUTION
BQC-PGM15X//1   
						

							Important
Information
8
How to Access the PDF Operation Manuals (for Windows and Macintosh)
PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to
install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet,
you can download it from the Internet (http://www.adobe.com) or install it from the CD-ROM.
To Install Acrobat Reader from the CD-ROM
For Windows:
1Insert the CD-ROM in the CD-ROM drive.
2Double click on the “My Computer” icon.
3Double click on the “CD-ROM” drive.
4Double click on the “manuals” folder.
5Double click on the “acrobat” folder.
6Double click on the “windows” folder.
7Double click on the desired installation program
and follow the instructions on the screen.
For Macintosh:
1Insert the CD-ROM in the CD-ROM drive.
2Double click on the “CD-ROM” icon.
3Double click on the “manuals” folder.
4Double click on the “acrobat” folder.
5Double click on the “mac” folder.
6Double click on the desired installation program
and follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the appropriate
version from the Internet.
Accessing the PDF Manuals
For Windows:
1Insert the CD-ROM in the CD-ROM drive.
2Double click on the “My Computer” icon.
3Double click on the “CD-ROM” drive.
4Double click on the “manuals” folder.
5Double click on the “pg-m15” folder.
6Double click on the language (name of the folder)
that you want to view.
7Double click on the pdf file.
For Macintosh:
1Insert the CD-ROM in the CD-ROM drive.
2Double click on the “CD-ROM” icon.
3Double click on the “manuals” folder.
4Double click on the “pg-m15” folder.
5Double click on the language (name of the folder)
that you want to view.
6Double click on the pdf file.
•If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired file
using the “File”, “Open” menu.
•See the “readme.txt” file on the CD-ROM for important information on the CD-ROM not included in this operation manual.