Sharp Projector Pg Lw3000 User Manual

19
Connections
Setting Up the Projector (Continued)
Pr\fjecti\fn (PRJ) M\f\be
The pro\bector can use any of the 4 pro\bection modes shown in the diagram below. Select the 
mode most appropriate for the pro\bection setting in use.  (You can set the PRJ mode in “SCR-
ADJ” menu. See page 49 .)
 
■ Table mounted, front pro\bection
[Menu item ➞ “\bront”]
 
■ Table mounted, rear pro\bection
(with a translucent screen)
[Menu item ➞ “Re\fr”]
 
■ Ceiling mounted, front pro\bection
[Menu item ➞ “Ceiling +...

20
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the pro\bector is unplugged from the AC outlet 
and turn off the equipment to be connected. After making all connections, turn on the pro\bector 
and then the other pieces of equipment. When connecting a computer, ensure that it is the last 
equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the pro\bector before 
you turn on...

21
Connections
Connecting the Projector to Other Equipment (Continued)
EquipmentTerminal on  
connected equipmentCable Terminal on t\fe 
projector
Video equipment
HDMI output  terminalHDMI cable (commercially available)HDMI
Component 
video output  terminal
3 RCA to mini D-sub 15 pin cable 
(commercially available)COMPUTER /
COMPONENT 1, 2
Video output  terminalVideo cable (commercially available)VIDEO
Audio equipmentø3.5 mm
audio output
terminalø3.5 mm stereo or mono audio cable
(commercially available...

22
EquipmentTerminal on  
connected equipmentCable Terminal on t\fe 
projector
Camera / Video game
Component  video 
output 
terminal
Cables for a camera or a video game/3 RCA to 
mini D-sub 15 pin cable (commercially available)
RCA adaptor plug
(commercially a\failable)
COMPUTER /
COMPONENT 1, 2
Video 
output 
terminal Cables for a camera or a video gameVIDEO
MonitorRG\b
input
terminalRG\b cable (supplied or commercially 
available)MONITOR OUT
Amplifierø3.5 mm
audio input terminal ø3.5 mm stereo or...

23
Connections
Controlling the Projector by \f Computer
When the RS-232C terminal on the pro\bector is connected to a computer with an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the pro\bector and check the status of the pro\bector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifications and Commands”.
When connecting to \f computer using \fn RS-232C seri\fl control c\fble

24
When connecting to the LAN termin\fl using \f LAN c\fble

25
B\fsic            
Oper\ftion
Turning the Projector On/Off
Turning the Pr\fject\fr On
Note that the connections to external 
equipment and power outlet should be 
done before performing the operations 
written below. (See pages 
20  to  22 .)
Press STANDBY/ON on the projector 
or ON on the remote control.
 

26
Im\fge Projection
Ab\fut the Setup Gui\be
After turning on the pro\bector, the Setup 
Guide screen appears to assist you with 
pro\bector setup.
Guidance items

1 	 

27
B\fsic            
Oper\ftion
2 A\bjusting the Height
The height of the pro\bector can be 
ad\busted using the ad\bustment feet at the 
front and rear of the pro\bector.
When the screen is above the pro\bector, 
the pro\bection image can be made higher 
by ad\busting the pro\bector.
1  Lift the projector to \fdjust its 
height while lifting the HEIGHT 
ADJUST lever.
2 Remove your h\fnds from the 
HEIGHT ADJUST lever of the 
projector \ffter its height h\fs 
been finely \fdjusted.
	 

28
C\frrecting Trapez\fi\bal  
Dist\frti\fn
When the image is pro\bected either from 
the top or from the bottom towards the 
screen at an angle, the image becomes 
distorted trapezoidally. The function for 
correcting trapezoidal distortion is called 
Keystone Correction.