Sharp Projector Pg Lw3000 User Manual

9
IntroductionC\fution reg\frding us\fge of the projector
 
■ If you are not to use the pro\bector for a long 
time or before moving the pro\bector, make 
certain you unplug the power cord from the 
wall outlet, and disconnect any other 
cables connected to it.
 
■ Do not carry the pro\bector by holding the 
lens.
 
■ Do not expose the pro\bector to direct 
sunlight or place next to heat sources. 
Doing so may affect the cabinet color or 
cause deformation of the plastic cover.
Other connected...

10
P\frt N\fmes \fnd \bunctions
Numbers in Z  refer to the main pages in this operation manual where the 
topic is explained.
13
11
12
1
2
5
6
3
4
7
9
8
1014
15 1617
\bront View
  1
  
Temperature warning indicator 61
  2
    Lamp indicator 61
  3
    Power indicator 61
  4
  
STANDBY/ON button 25	 	 	r 	 g 	 e 	 

11
Introduction
1 2345
10
11
6789
12
13
14
Rear View (Termina\fs)
  1
	 HDMI 	 terminal 	2\b, 21, 22
Terminal for HDMI input.
  2	 	AUDIO	 2 	 input 	 terminal 	21
  3
	 	\fIDEO 	 input 	 terminal 	21 Terminal for \fonne\fting video e\buipment.
  4	 	COMPU\bER/COMPONEN\b 	 1 	 input 	
terminal 	2\b, 21Terminal for \fomputer RGB and 
\fomponent signals.
  5	 AUDIO	 1 	 input 	 terminal 	22
  6
	 MONI\bOR 	 OU\b* 	 terminal 	 	22, 52(Output terminal for \fomputer RGB and 
\fomponent signals) 
Terminal for...

12
P\frt N\fmes \fnd \bunctions (Continued)
Numbers in Z  refer to the main pages in this operation manual where the 
topic is explained.
2
3
4
8
10
11
6
1
7
9
12
13
14
16
18
20
21
22
19 17
515
Ad\bustment buttons ( P/R /O /Q ) 39r 	 g 	 d 	 	g 	  	 9
ON button 25r	 g 	 e 	 

13
IntroductionInserting the Batteries
1 Pull down the t\fb on the cover \fnd remove the 
cover tow\frds the direction of the \frrow.
2 Insert the b\ftteries.

14
E\fsy St\frt
This section shows the basic operation (pro\bector connecting with the computer). For details, 
see the page described below for each step.
Setup an\b Pr\fjecti\fn
In this section, connection of the pro\bector and the computer is explained using one example.


15
E\fsy St\frt
1 After the pro\bector turns on, the Setup Guide appears.
  (When “Setup Guide” is set to “On”. See page  49 .)
2 Follow the steps in the Setup Guide and ad\bust the focus, height (angle) and picture size.
3 After ad\busting the focus, height (angle) and picture size, press ENTER to finish the 
Setup Guide.
4.  Adjust the projected im\fge with the Setup Guide
_ P. 26
Correcting trapezoidal distortion using Keystone Correction.

16
Setting Up the Projector
Vi\be\f Setup
If using this pro\bector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See 
page 46 .)
Setting Up the Pr\fject\fr
For optimal image quality, position the pro\bector perpendicular to the screen with the pro\bector's 
feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best 
image quality. (See page 
28 .)
Stan\bar\b Setup (Fr\fnt Pr\fjecti\fn)
 
■ Place the pro\bector at the required distance...

17
Setup
Screen Size and Projection Distance
ScreenLens center
H L
[PG-LW3000/PG-LW3500]
16\f10 Sig\bal I\bput (Normal Mode)
Picture (Screen) size Projection distance \[[\f]Distance fro\b the lens center 
to the botto\b of the i\bage [H]Diag. [ χ
] Width HeightMini\bu\b [\f1] Maxi\bu\b [\f2]
300" (762 cm) 646 cm(2\f4") 404 cm(1\f9") 10.0 m(32\b 9") 12.0 m(39\b 6") 7 cm(2 37/64")
2\f0" (63\f cm) \f38 cm(212") 337 cm(132") 8.3 m(27\b 4") 10.0 m(32\b 11") \f cm(2...

18
Screen Size and Projection Distance (Continued\f
ScreenLens center
H L
[PG-LX3000/PG-LX3500]
4\f3 Sig\bal I\bput (Normal Mode)
Picture (Screen) size Projection distance \[[\f]Distance fro\b the lens center 
to the botto\b of the i\bage [H]Diag. [ χ
] Width HeightMini\bu\b [\f1] Maxi\bu\b [\f2]
300" (762 cm) 610 cm(240") 4\f7 cm(180") 11.8 m(38\b 9") 14.2 m(46\b \f") 17 cm(6 23/32")
2\f0" (63\f cm) \f08 cm(200") 381 cm(1\f0") 9.9 m(32\b 4") 11.8 m(38\b 8")...