Sharp Projector Pg C45x User Manual

Appendix
-87
Securing
screw
AC socket
INPUT button
ENTER button User service screw
UNDO buttom Power (ON)
button
5Remove the lamp unit.
•Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of
the arrow.
6Insert the new lamp unit.
•Press the lamp unit firmly into the lamp
unit compartment. Fasten the secur-
ing screws.
7Attach the lamp unit cover.
•Insert the tab of the lamp unit cover
into the opening, and press the cover
until it clicks in place....

-88
RS-232C Terminal:9-pin Mini DIN female connector
Pin No. Signal Name I/O Reference
1 VCC +3.3V (Reserved)  Output Not connected
2 RD Receive Data Input Connected to internal circuit
3 SD Send Data Output Connected to internal circuit
4 EXIR Detector of Option Unit Input Not connected
(Reserved)
5 SG Signal Ground Connected to internal circuit
6 ERX IR Receive Signal from Input Not connected
IR Amplifier (Reserved)
7 RS Request to Send  Output Not connected
8 CS Clear to Send Input Not connected
9 ETX...

Appendix
-89
CONTROL CONTENTS
BLACK SCREEN ON
BLACK SCREEN OFF
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT CHECK
FREEZE ON
FREEZE OFF
AUTO SYNC STARTOK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR
OK OR ERR I
I
I
I
I
I
I
F
F
AM
M
R
R
V
V
C
R
R
DB
B
G
G
E
E
H
E
E
JK
K
B
B
D
D
K
Z
Z
S_
_
_
_
_
_
_
_
_
__
_
_
_
_
_
_
_
_
__
_
_
_
_
_
_
_
_
_1
0
1
2
1
2
0
1
0
1
BUTTONS & REMOTE CONTROL KEY
COMMANDPARAMETERRETURNCONTROL CONTENTS
POWER ON
POWER OFF
VOLUME (0 - 60)
MUTE ON...

-90
CONTROL CONTENTS
INPUT 1 RESIZE : NORMAL
INPUT 1 RESIZE : FULL
INPUT 1 RESIZE : DOT BY DOT
INPUT 1 RESIZE : STRETCH
INPUT 1 RESIZE : SMART STRETCH
INPUT 2 RESIZE : NORMAL
INPUT 2 RESIZE : FULL
INPUT 2 RESIZE : DOT BY DOT
INPUT 2 RESIZE : STRETCH
INPUT 2 RESIZE : SMART STRETCH
INPUT 3 RESIZE : NORMAL
INPUT 3 RESIZE : BORDER
INPUT 3 RESIZE : STRETCH
INPUT 3 RESIZE : SMART STRETCH
INPUT 4 RESIZE : NORMAL
INPUT 4 RESIZE : BORDER
INPUT 4 RESIZE : STRETCH
INPUT 4 RESIZE : SMART STRETCH
RGB GAMMA :...

Appendix
-91
CONTROL CONTENTS
FAO
VAO
SPEAKER ON
SPEAKER OFF
PICT IN PICT : BOTTOM RIGHT
PICT IN PICT : BOTTOM LEFT
PICT IN PICT : UPPER RIGHT
PICT IN PICT : UPPER LEFT
PICT IN PICT OFF
POWER SAVE: STANDARD
POWER SAVE: LOW POWER
DNR : OFF
DNR : LEVEL 1
DNR : LEVEL 2
DNR : LEVEL 3
AUTO SEARCH: OFF
AUTO SEARCH: ON
OSD DISPLAY NORMAL
OSD DISPLAY LEVEL A
OSD DISPLAY LEVEL B
BLACK SCREEN DISPLAY ON
BLACK SCREEN DISPLAY OFF
VIDEO SYSTEM SELECTION : AUTO
VIDEO SYSTEM SELECTION : PAL (50/60 Hz)
VIDEO SYSTEM...

-92
CONTROL
ITEMSYSTEM CODEC1
1
1
1
1
1
1
1
1
1
1
1
1
1
1ON
OFF
VOLUME +
VOLUME –
MUTE
MENU
KEYSTONE 
BLACK SCREEN
ENTER
RESIZE
UNDO
FREEZE
ENLARGE (+)
ENLARGE (–)0
0
0
0
0
0
0
0
0
0
0
0
0
0
C2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
C5 C6
0
0
0
1
1
0
1
1
1
0
1
1
1
11
1
0
0
1
0
1
0
1
1
0
0
0
0
C7
1
1
1
1
1
1
0
0
1
1
0
1
1
1
C8
0
0
0
0
0
0
1
1
0
1
1
1
1
1
C9
1
1
1
1
1
0
0
0
1
1
1
0
0
0
C10 C11
0
0
0
0
0
0
0
1
0
0
0
0
1
11
0
0
0
0
1
0
1
1
1
1
0
1
0
C12
0
1...

Appendix
-93
Computer Compatibility Chart
Note
•This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off
the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can
be found in your notebook computer’s operation manual.
•When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
•
When receiving 1,600 × 1,200 VESA...

-94
Troubleshooting
Check
•Projector power cord is not plugged into the wall outlet.
•Power to the external connected devices is off.
•The selected input mode is wrong.
•Cables incorrectly connected to rear panel of the projector.
•Remote control batteries have run out.
•External output has not been set when connecting notebook computer.
•The cover of the lamp unit is not installed correctly.
•Cables incorrectly connected to the rear panel of the projector.
•“Bright” is set to minimum position.
•Picture...

Appendix
-95
CheckProblemPage
Pict in Pict does not
work.
Power cannot be turned
on or off using the power
buttons on the projector.
Picture is green on
INPUT 1 or 2
COMPONENT.
Picture is pink (no green)
on INPUT 1 or 2 RGB.
Picture is dark.
Picture is too bright and
whitish.
The VOLUME buttons
on the projector do not
work.
A response code cannot
be received when the
projector was attempted
to be controlled using
RS-232C commands
from a computer during
standby.•The signal in INPUT 1 or 2 is set to a...

-96
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the
“Troubleshooting” section on pages 94 and 95. If this operation manual does not answer
your question, please contact the SHARP Service departments listed below.
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
[email protected]
http://www.sharplcd.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca
Mexico Sharp Electronics Corporation...