Sharp Projector Dt 400 User Manual

-21
Connections
Connecting to Video Equipment
Before connecting, ensure to unplug the power cord of the projector from the AC outlet and
turn off the devices to be connected. After making all connections, turn on the projector and
then the other devices.
Ensure to read the operation manuals of the devices to be connected before making connections.
When connecting the component video equipment to the component input terminal on the
projector (INPUT 1 or INPUT 2)
Component cable
(commercially...

-22
When connecting the video equipment with RGB output terminal (INPUT 5)
•Before connecting the cable, switch the digital input type switch to “VIDEO”.
INPUT 5 terminal
DVI to 15-pin D-sub adaptor
(sold separately: AN-A1DV) RGB output terminal
RGB cable
(commercially available)
DVD Player,etc.
4
32
Switch to “VIDEO”1
Connecting to Video Equipment
Note
•For this connection, select “RGB” for “Signal Type” on the OSD menu or press  on the remote control.
(See page 48.)
When connecting the component video...

-23
Connections
DIGITAL terminal
DVI output terminal
DVI cable
(sold separately: AN-C3DV)
Switch to “VIDEO”DVD Player,etc.
2
31
Note
•Select DIGITAL mode when connecting to video equipment with the digital output terminal. (See page
29.)
When connecting the video equipment with DVI output terminal (DIGITAL INPUT)
•Before connecting the cable, switch the digital input type switch to “VIDEO”.
DT400_E_P19_26.p6504.10.18, 1:17 PM 23 

-24
When connecting video equipment with S-video output terminal (INPUT 3)
When connecting video equipment with video output terminal (INPUT 4)
S-video cable
(commercially available) S-video output terminal
INPUT 3 terminal
DVD Player,etc.
2
1
INPUT 4 terminal Video output terminal
Composite video cable
(commercially available)
DVD Player,etc.
1 2
Connecting to Video Equipment
DT400_E_P19_26.p6504.10.18, 1:17 PM 24 

-25
Connections
Connecting to a Computer
Connecting to a computer (INPUT 5)
•Before connecting the cable, switch the digital input type switch to “PC”.
RGB output terminalINPUT 5 terminal
RGB cable (commercially available)
DVI to 15-pin D-sub adaptor
(sold separately: AN-A1DV)
Computer
4
32
Switch to “PC”1
Note
•Refer to “Computer Compatibility Chart” on page 60 for a list of computer signals compatible with the projector. Use
with computer signals other than those listed may cause some of the functions...

-26
Connecting to a computer with DIGITAL RGB output Terminal (DIGITAL)
•Before connecting the cable, switch the digital input type switch to “PC”.
INPUT 5 terminal
DVI output terminal
DVI cable
(sold separately: AN-C3DV)
Switch to “PC”
Computer
2
31
Note
•Select DIGITAL mode when connecting to digital output terminal of the computer. (See page 29.)
•Before switching “Digital input type switch” and connecting, ensure to unplug the power cord of the pro-
jector from the AC outlet and turn off the computer...

-27
Basic Operation
Connecting the Power Cord
Plug the supplied power cord into the
AC socket.
Turning the Projector On
Before performing the steps in this section,
connect any equipment that you use with the
projector. (See pages 19-26.)
Remove the lens cap and press  on the
projector or  
 on the remote control.
•The power indicator illuminates green.
•After the lamp indicator illuminates, the projec-
tor is ready to start operation.
Note
•The lamp indicator illuminates or blinks, in-
dicating the...

-28
STANDBY
button
STANDBY
button
Info
•Do not unplug the power cord during projec-
tion or cooling fan operation. The cooling fan
in this projector continues to run for about 90
seconds after the projector enters the standby
mode. This can cause damage due to rise in
internal temperature, as the cooling fan also
stops.
Turning the Power Off (Put-
ting the Projector into Standby Mode)
1Press  on the projector or 
on the remote control, then press
that button again while the confir-
mation message is...

-29
Basic Operation
Switching the INPUT
Mode
Select the appropriate input mode for the con-
nected equipment.
Press  ,  ,  ,  ,  or  on
the remote control to select the input
mode.
• •• •
•When pressing  on the projector, input mode
switches in order of :
INPUT 1 INPUT 2 INPUT 3
INPUT 5 INPUT 4DIGITAL
Note
•When no signal is received, “NO SIGNAL”
will be displayed. When a signal that the
projector is not preset to receive is received,
“NOT REG.” will be displayed.
•The INPUT mode is not displayed when...

-30
Image Projection
ZOOM/FOCUS 
button
Adjustment buttons
('/"/\/|)
Adjustment
buttons ('/"/\/|)
ZOOM/FOCUS
button
Adjusting the Focus
1Press  on the remote control.
2Press \ or | on the remote con-
trol to adjust the focus.
Note
•You can also adjust the focus by using
 and \ \\ \
\ or | || |
| on the projector.
Adjusting the Projected Image Size
1Press  on the remote control.
2Press ' or " on the remote con-
trol to adjust the zoom.
Note
•You can also adjust the zoom by using...