Sharp Projector Dt 400 User Manual

-11
Introduction
Projector (Rear View)
Using the Kensington Lock
•This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
Numbers in  refer to the main pages in this operation manual where the topic is explained.
13Remote control sensor
28AC socketConnect the supplied 
Power cord.
11Kensington Security 
Standard connector
31
537
Rear...

-12
Remote Control
Adjustment buttons
('/"/\/|)
38
30
MENU buttonDisplay adjustment and setting 
screens.38
ON buttonTurn the power on.28
30ZOOM/FOCUS buttonAdjust the projected image 
size or adjusting the focus.
29INPUT 3 button
29INPUT 5 button
34
34
44
RESIZE buttonSwitch the picture display
(STRETCH, SIDE BAR, etc.).
29DIGITAL INPUT button
PICTURE MODE button
Select the picture setting (Memory) 
stored in “Picture Mode” on the 
“Picture” menu.
29STANDBY buttonPut the projector into standby...

-13
IntroductionUsing the Remote Control
Inserting the Batteries
1Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
2Insert the included batteries
(two “AA” size).
•Insert the batteries making sure the po-
larities correctly match the 
 and 
marks inside the battery compartment.
3Insert the lower tab of the cover
into the opening, and lower the
cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the...

-14
Quick Start
3  ON button
8  STNADBY button
4  INPUT button 6  ZOOM/FOCUS button
6  
Adjustment buttons ('/"/\/|)
6  HEIGHT ADJUST button
8  STNADBY button
3  ON button
7  KEYSTONE button
6, 7  Adjustment buttons        ('/"/\/|)
6  ZOOM/FOCUS button
4  INPUT buttons,
    DIGITAL INPUT button
Page 16
1.Place the projector facing a screen
Pages 21-27
Page 27
On the remote control On the projector This section shows the basic operation. For details, see the page described below for each...

-15
Quick Start
Page 29
4.Select the INPUT mode
6.Adjust the projector angle, focus and zoom
Select the “INPUT 3” using the INPUT button on the projector or the INPUT 3 button on the remote control.
• •• •
•When pressing  on the projector, input mode switches in order of :
INPUT 1 INPUT 2 INPUT 3 INPUT 4INPUT 5DIGITAL
• •• •
•When using the remote control, press ///// to switch the INPUT mode. On the remote
control On the
projector" "" "
" On-screen Display
5.Turn the video equipment...

-16
Setting Up the Projector
Position the projector perpendicular to the screen to achieve an optimal image.
Note
•The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
•For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult....

-17
Setup
H
L
Side View
Screen
Lens center
Screen Size and Projection Distance
The projection screen size varies according to the distance from the lens of the projector to the screen.
Install the projector so that projected images are projected onto the screen at the optimum size by referring
to the table below. Use the values in the table as a reference when installing the projector.
Picture (Screen) size Projection distance [L]Diag. [χ
]Width Height Minimum [L1] Maximum [L2]
200 174 98 17 4 (5.29 m)...

-18
Setting Up the Projector
Projecting a Reversed Image
Projection from behind the Screen
■Place a translucent screen between the projector and the audience.
■Reverse the image by setting “Rear” in the “PRJ Mode” menu. (See page 52.)
Projection Using a Mirror
■Place a mirror (normal flat type) in front of the lens.
■When the translucent screen is placed between the mirror and audience, set to “Front” in the “PRJ Mode”
menu. (See page 52.)
■When the mirror is placed on the audience side, set to “Rear” in...

-19
Connections
INPUT Terminals and Connectable Main Equipment
INPUT 5/DIGITAL terminalConnecting video equipment with 
component output terminal (DVD 
player, DTV decoder, DVD recorder 
with hard disc, etc.). (See pages 22, 
23.)
Connecting the computer. (See 
pages 25, 26.)INPUT 3 terminalConnecting video equipment with S-video 
output terminal (VCR, DVD player, etc.).
(See page 24.)
INPUT 1, 2 terminalConnecting video equipment with 
component output terminal (DVD 
player, DTV decoder, DVD recorder...

-20
Terminal on the
projector
INPUT 1, 2
INPUT 1, 2
INPUT 5/DIGITAL
INPUT 5/DIGITAL
INPUT 4
INPUT 4
INPUT 3
INPUT 3 Equipment
Audio-visual
equipment
Computer
Terminal on
connected equipment
Component
video 
output
terminal
Terminal
for using
the
dedicated
cable
DVI output
terminal
RGB output
terminal
Video
output
terminal
Terminal
for using
the
dedicated
cable
S-video
output
terminal
Terminal
for using
the
dedicated
cableCable
Component cable (commercially available)
Dedicated cable attached to the...