Sharp Projector Dt 300 User Manual

On-screen Display
-50
Adjusting the Computer and DVD/DTV Images
AUTO SYNC button
On-screen Display
 (ON)
 (OFF)
Selected ItemDescription
Auto Sync adjustment will occur
when the projector is turned on or
when the input signals are switched,
when connected to a computer.
Auto Sync adjustment is not
automatically performed.
Auto Sync Adjustment
Used to automatically adjust a computer im-
age.
Select whether the image is to be synchro-
nized automatically when switching the sig-
nal with “ON” or “OFF”....

-51
Adjustments and Settings
 (ON)
 (OFF)
Checking the Lamp Life
Status
You can confirm the cumulative lamp usage
time and the remaining lamp life (percentage).
Display the “Options” menu to check
the lamp life status.
➝For operating the menu screen, see
pages 38 to 41.
Note
•It is recommended that the lamp be
changed when the remaining lamp life
becomes 5%.
For lamp replacement, contact your near-
est Sharp Authorized Service Center or
Dealer.
•The table above indicates rough estimates
in the case of...

-52
Using the “Options” Menu
-52
Selecting the Signal
Type
This function allows you to select the input
signal type Component or RGB for INPUT 2.
Select “Signal Type” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Note
•“RGB” or “Component” can be selected
with 
 on the remote control only in
INPUT 2.
On-screen Display
Setting the Video Signal
(VIDEO menu only)
The video input system mode is preset to
“Auto”; however, it can be changed to a spe-
cific system...

-53
Adjustments and Settings
Selecting a
Background Image
This function allows you to select the image
displayed when no signal is being sent to the
projector.
Select “Background” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.
Blue screen
Black screen (Blue)
 (None)
Selected ItemDescription
On-screen Display
Setting the Eco Mode
This function allows you to select the desired
power consumption mode.
Select “Eco Mode” in the “Options”
menu on the menu screen....

-54-54
Using the “Options” Menu
Selecting the Menu
Screen Position
This function allows you to select the desired
position of the menu screen.
Select “Menu Position” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.On-screen Display
Center
Upper
Right
Lower
Right
Upper
Left
Lower
Left
Selected Item
The menu is displayed on thecenter of the image.
The menu is displayed on the
upper right of the image.
The menu is displayed on the
lower right of the image.
The...

-55
Adjustments and Settings
Selecting the Menu
Color
This function allows you to select the color of
the menu screen.
Select “Menu Color” in the “Options”
menu on the menu screen.
➝For operating the menu screen, see
pages 38 to 41.On-screen Display
The menu is displayed
opaquely.
The menu is displayed
translucently. The part of the
menu on the image becomes
transparent.
 (Opaque)
(Translucent)
Selected ItemDescription
%5@&@Q@Q03.10.29, 2:46 PM Page 55EPCF
1BHF.BLFS
+11$ 

-56-56
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or
invert the projected image for various applications.
Setting the Projection
Mode
Display the “PRJ Mode” menu and se-
lect the desired projection mode.
➝For operating the menu screen, see
pages 38 to 41.
Note
•This function is used for the reversed im-
age and ceiling-mount setups. See page 28
for these setups.
On-screen Display
Normal image
Inverted image
Reversed...

Appendix
Appendix
%5@&@Q@Q03.10.29, 2:47 PM Page 57EPCF
1BHF.BLFS
+11$ 

-58
Maintenance Indicators

The warning lights on the projector indicate problems inside the projector.

If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby
mode, follow the procedures given below.
TEMPERATURE
WARNING
indicatorPOWER
indicator LAMP
indicator
TEMP. LAMP POWER
About the temperature warning indicator
If the temperature inside the
projector increases,...

Appendix
-59
Regarding the Lamp
Info
•If the temperature warning indicator illuminates, and the projector enters the standby mode, follow the pos-
sible solutions on the previous page and then wait until the projector has cooled down completely before
plugging in the power cord and turning the power back on. (At least 5 minutes.)
•If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp...