Sharp Projector Dt 300 User Manual

DT-300
SHARP CORPORATION
Printed in Japan
Imprimé au Japon
Impreso en Japón
Impresso no Japão
TINS-B006WJZZ
03P11-JWM Printed on 100% post-consumer recycled paper.
Imprimé sur 100% de papier recyclé.
Impreso en 100% de papel reciclado de postconsumo.
Papel 100% Reciclado - Cuidado do Meio Ambiente.
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACION
MANUAL DE OPERAÇÃO
DT-
300
PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR
ENGLISH ............. -1 –  -71
FRANÇAIS ...........
 -1 –  -70
ESPAÑOL ............
 -1 –...

Introduction
-1
Before using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification,...

-2
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.
During normal operation, when putting the projector into the standby mode always use the STANDBY button on the
projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE....

Introduction
-3
Contents
Introduction
Contents ............................................................... 3
IMPORTANT SAFEGUARDS ............................... 4
Quick Guide ......................................................... 7
Part Names .......................................................... 8
Operating the Remote Control ......................... 11
Accessories ....................................................... 12
Connections & Setup
Connecting the Projector to Other Devices ......

-41. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain InstructionsThe safety and operating instructions should be
retained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be followed.
5. CleaningUnplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners....

Introduction
-5 18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an...

-6
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up
your projector.
Caution concerning the lamp unit

There is a potential hazard of glass
particles if the lamp ruptures. In case
of lamp rupture, contact your near-
est Sharp Authorized Service Cen-
ter or Dealer for replacement.
See “Replacing the Lamp” on page
59.
Cautions concerning the setup of the projector

For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be installed
in an...

Introduction
-7
The power indicator
illuminates green.
In this page, connection of the projector and the video equipment is explained as an example
for the procedure from setup to projection. Refer to each page for details.
Quick Guide
Required equipments
Video cable
Projector Remote control
•Insert the batteries.
(Page 11)Power cord
1. Place the projector facing a wall or a screen.
2. Connect to video equipment. (Page 16)6. Turn the projector on using  on the remote
control. (Page 30)
3. Connect the...

-8
Projector (Front and Top View)
Part Names
Numbers in  refer to the main pages in this operation manual where the topic is explained.
30
58
58
POWER indicator
6Exhaust ventilative hole LAMP indicator TEMPERATURE 
WARNING indicator
39ADJUSTMENT buttons
(ƒ/∂/ß/©) 
39UNDO button
38MENU button
35RESIZE button
31INPUT button
23Swivel Stand 
LOCK/UNLOCK lever
11Remote control sensor
Lens cap
Zoom knob25
Exhaust ventilative hole6
Focus ring25
25Lens shift dial
39ENTER button
33KEYSTONE button
ON button30...

Introduction
-9
Projector (Rear View)
17
16
62Intake ventilative hole
AC socketIntake ventilative hole
62
18INPUT 2/DIGITAL INPUT
terminal
INPUT 1 COMPONENT
terminals (RCA)
INPUT 4 VIDEO terminal (RCA)
20DIGITAL INPUT
TYPE switch
15INPUT 3 S-VIDEO terminal
 (4-pin Mini DIN)RS-232C terminal
    (Serviceman only) 
11Remote control sensor
14
%5@&@Q@Q03.10.29, 2:38 PM Page 9EPCF
1BHF.BLFS
+11$