Sharp PNV602 Lcd Monitor User Manual

11E
Part Names
n Remote control unit 
 
(Supplied with the PN-ZR01 (optional))
1
2
3
4
5
6
7 129
10 11 8 
1.  Signal transmitter
  2.  POWER button
  3.  MUTE button
  4.  VOL +/Cursor control (
) button
  5.  BRIGHT -/Cursor control (
) button
  6.  DISPLAY button
  7.  MODE button
  8.  INPUT button
  9.  MENU button
 
10.  BRIGHT +/Cursor control (
) button
 
11.  VOL -/Cursor control (
) button
 
12.  SIZE button
nRemote control sensor box  
(Supplied with the PN-ZR01 (optional))
1
2
3 4 
1....

12E
11
10
9
81 2345 7
12
6
15 14
13 17
16
Expansion Board
When the PN-ZB02 (optional)  
is attached
Caution
•	 Be	sure	to	turn	off	the	main	power	switch	and	disconnect	
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the 
equipment	to	be	connected.
•	 Be	careful	not	to	confuse	the	input	terminal	with	the	output	 terminal when connecting cables. Accidentally reversing 
cables connected to the input and output terminals may 
cause malfunctions and the other...

13E
Connecting Peripheral Equipment
TIPS
•	 The	length	of	the	signal	cables	or	surrounding	environment	
may	affect	the	image	quality.
•	 The	screen	may	not	display	properly	when	using	terminals	 other	than	PC	DVI-D/AV	DVI-D	for	the	input	mode.	In	this	
case, turn off the power to all the monitors connected in a 
daisy chain and then turn the power on again.
•	 When	connecting	monitors	in	 a	daisy	chain	set	AUTO	
INPUT 	CHANGE	to	OFF.
•	 Video	output	is	disabled	in	the 	following	cases: 
When	the	power	is...

14E
■ Connection with RS-232 cable
If	you	connect	the	monitor	in	a	daisy	chain	using	RS-232	
cable, using the monitor buttons on the primary (main unit), 
settings are copied to the secondary (expansion unit) and 
operation from the primary can perform operation for all 
monitors.	Setting	each	ID	No.	in	the	monitor	is	required.
1. Connect the monitors in order.
The	first	monitor	will	be	set	as	primary	(main	unit)	and	the	
second monitor and beyond will be secondaries (expansion 
units).
Connect	the...

15E
Connecting the Power Cord
Caution
•	 Use	only	the	power	cord	supplied	with	the	monitor.
1.	 Turn	off	the	main	power	switch.
2.	Plug	the	power	cord	(supplied)	into	the	 AC	input	terminal.
3.	Plug	the	power	cord	(supplied)	into	the	 AC	power	outlet.
AC input terminal
1
Main power switch
Power cord (Supplied)
For power 
outlet
23
Preparing the Remote Control Unit
Installing the batteries
1.	 Press	the	cover	gently	and	slide	it	in	the	direction	of	the	
arrow.
2. See the instructions in the compartment...

16E
Binding Cables
The cables connected to the terminals on the rear of the monitor can be \
fastened with the cable clamps.
Insert the cable clamp into the cable clamp attachment on the rear of th\
e monitor and fasten the cables.
: Cable clamp attachment
Cable clamp
Cable
Cable clamp 
attachment
Removing the Handles
The handles can be removed.
The removed handles can be attached on the side.
1.	 Remove	the	handle	screws	and	remove	the	handles	and	 handle spacers.
2.  Pass the handle screws through the...

17E
Turning Power On/Off
Caution
•	 Turn	on	the	monitor	first	before	turning	on	the	PC	or	playback device.
Turning on the main power
Main power switch
Caution
•	 The	main	power	must	be	turned	on/off	with	the	main	power	switch.	Do	not	connect/disconnect	the	power	cord	or	turn	
the breaker on/off while the main power switch is on.
•	 When	switching	the	main	power	switch	or	the	POWER	 button	off	and	back	on,	always	wait	for	at	least	5	seconds.
•	 For	a	complete	electrical	disconnection,	pull	out	the	main...

18E
Basic Operation
When	performing	operation	of	multiple	monitors	with	the	
remote	control	unit,	first	set	the	remote	control	unit	to	the	
appropriate	remote	control	mode	(see	page	21).
1
2 3
4
5
6
7
8
TIPS
•	 You	can	perform	operation	of	the	monitor	with	the	rear	
buttons.	Utilize	the	buttons	belonging	to	the	monitor	that	
you would like to operate.
•	 Operation	by	using	the	buttons	on	the	rear	side	of	the	 product will perform the same functions.
Rear side buttons
Remote control 
unit buttons
  This...

E19
5. BRIGHT +/- (Backlight adjustment)
Pressing 
 or 	displays	the	BRIGHT	menu	when	the	
menu screen is not displayed.
BRIGHT  15
Press  or 	to	adjust	the	brightness.
*	 If	 you	do	not	press	any	buttons	for	about	4	seconds,	the	
BRIGHT 	menu	automatically	disappears.
*	 When	BRIGHTNESS	SENSOR	is	ON	or	ON:	DISPLAY,	 when	the	brightness	is	adjusted	BRIGHTNESS	SENSOR	
will	become	OFF.
6. SIZE (Screen size selection)
The menu is displayed.
Press 
 or 	to	select	the	screen	size.	(See	page	20.)
If	using	the...

E20
Basic Operation
n Switching the screen size
Even	when	the	screen	size	is	changed,	the	display	may	remain	the	same	depending	on	the	input	signal.
WIDEPC	input
Displays	image	so	it	fills	the	entire	screen.
AV	input An	image	with	a	4:3	aspect	ratio	is	stretched	to	fill	the	entire	
screen.
ZOOM 1
PC	input An	image	with	a	4:3	aspect	ratio	is	enlarged	to	fill	the	entire	screen	
without changing the aspect ratio. The edges of the image may be 
cut off.
AV	input
ZOOM 2
PC	input Use	this	size	if	ZOOM	1	cuts...